Polaris 3900 Sport/P39 Owner's Manual
  1. Manuals
  2. Brands
  3. Polaris Manuals
  4. Swimming Pool Vacuum
  5. 3900 Sport/P39
  6. Owner's manual

Polaris 3900 Sport/P39 Owner's Manual

Hide thumbs Also See for 3900 Sport/P39:

Advertisement

Table of Contents

See also: Owner's Manual
3900 Sport/P39
OWNER'S MANUAL
|
|
ENGLISH
FRANÇAIS
ESPAÑOL

Advertisement

Table of Contents
loading

Related Manuals for Polaris 3900 Sport/P39

Summary of Contents for Polaris 3900 Sport/P39

  • Page 1 3900 Sport/P39 OWNER’S MANUAL ENGLISH FRANÇAIS ESPAÑOL...
  • Page 2 • Always remove the Polaris from the pool before super oxidation or chlorination treatments. WARNING To avoid risk of injury, do not handle the Polaris while it is operating, except when checking the wheel RPM. Always remove the cleaner before swimmers enter the pool.
  • Page 3 Polaris dealer or service center. Always insist on genuine Polaris replacement parts. Non-Polaris parts are not made to our specifications. They may have an adverse effect on the operation of your Polaris or may even damage it.

  • Page 4: Quick Installation Instructions

    Page 4 Quick Installation Instructions Install the Universal Wall Fitting 1. Turn on the filtration pump and flush out the plumbing line.Turn pump off. 2. Remove the Universal Wall Fitting (UWF ) from the Quick Disconnect and screw it ® into the return opening with the blue restrictor disk in place.
  • Page 5 (Refer to booster pump manufacturer’s instructions for booster pump priming time.) Check for Proper RPM Single-wheel Side Before operating the Polaris, check for proper wheel revolutions per minute (RPM). For maximum efficiency, the cleaner should operate between 30 and 36 RPM.

  • Page 6: Thrust Jet Adjustment

    Page 6 Fine Tuning The Cleaner When operating correctly, the cleaner vacuums, sweeps and scrubs all surfaces randomly throughout the pool. Approximately every three (3) minutes the cleaner goes into back-up mode. This action pulls the cleaner away from pool obstacles and increases its random pattern. Thrust Jet Adjustment The thrust jet powers the direction of the cleaner.

  • Page 7: Storage And Winterizing

    CAUTION Always disconnect the Polaris before cleaning or backwashing your pool filter to avoid potential clogging or damage to the system. Allow the filtration system run for at least five (5) minutes before re-connecting the cleaner.
  • Page 8 No. Part # Description No. Part # Description No. Part # Description 1 39-310 3900 Sport/P39 SuperBag* 22 39-300 WMS Assembly with O-Ring 1 38 D16 Nut, Feed Hose, Black 2 39-003 3900 Top Housing Assembly 1 22A R0544000 O-ring WMS Upper to...

  • Page 9: Troubleshooting

    3. Make sure the feed hose loss of water pressure. is floating. 4. Check the wheel RPM. If 4. With the Polaris operating, below 30 RPM, see Adjusting the hold the cleaner under water and Wheel RPM to increase flow to verify that all three (3) wheels are cleaner.

  • Page 10: Adjusting Wheel Rpm

    • If an adjustable valve is installed on the scrubber if it is worn or missing. cleaner line, open it completely so water can flow freely to the Polaris. 2. Adjust the sweep hose to a gentle sweeping motion. • Check the filter screen in the in-line filter for debris that restricts water flow.
  • Page 11 Customer Service. In order to provide faster and more convenient service, please have the fol- lowing information available at the time of your call or when taking the Polaris in for service. Serial #:________________________ Wheel RPM:__________________ Is the back-up valve cycling?
  • Page 12 Zodiac Pool Systems, Inc. 2620 Commerce Way, Vista, CA 92081 1.800.822.7933 | www.ZodiacPoolSystems.com ZODIAC is a registered trademark of Zodiac International, S.A.S.U., used under license. ® All other trademarks referenced herein are the property of their respective owners. ©2014 Zodiac Pool Systems, Inc. TL-875 Rev D...

Table of Contents