Specifications; Intended Use - Makita DSP600 Instruction Manual

SPECIFICATIONS

Model:
Blade diameter
Max. Cutting depth
No load speed
Overall length
Rated voltage
Battery cartridge
Charger
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Only for EU countries
Ni-MH
Li-ion Do not dispose of electric equipment or
battery pack together with household waste
material!
In observance of the European Directives,
on Waste Electric and Electronic
Equipment and Batteries and Accumulators
and Waste Batteries and Accumulators
and their implementation in accordance
with national laws, electric equipment and
batteries and battery pack(s) that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.

Intended use

The tool is specially intended for performing plunge
cuts. The tool is also intended for rip and cross cuts in
wood. If the tool is equipped with proper circular saw
blade, the tool can be used for sawing aluminum, plas-
tic, mineral contained plastic, and similar materials.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Model DSP600
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DSP601
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
at 0°
at 45° bevel
at 48° bevel
) : 92 dB(A)
pA
) : 92 dB(A)
pA
DSP600
BL1815N, BL1820, BL1820B, BL1830, BL1830B, BL1840,
BL1840B, BL1850, BL1850B, BL1860B
DC18RC, DC18RD, DC18SD, DC18SE, DC18SF
WARNING:
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Model DSP600
Work mode: cutting wood
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: cutting metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DSP601
Work mode: cutting wood
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: cutting metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
2 ENGLISH
DSP601
165 mm
56 mm
40 mm
38 mm
-1
2,500 - 6,300 min
346 mm
D.C. 36 V
4.4 - 5.1 kg
2
) : 2.5 m/s or less
h,W
2
2
) : 2.5 m/s or less
h,M
2
2
) : 2.5 m/s or less
h,W
2
2
) : 2.5 m/s or less
h,M
2