Custom Code Setting; Function Setting - Fujitsu AUXB07L Installation Manual

Example If 4 indoor units are connected.
Indoor unit Indoor unit
RC AD SW RC AD SW
0 1
Remote
controller
RC AD SW 0 1
Address 0 1
RC AD SW 8 9
Address 8 9

7.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up.
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote
controller.
Confusion
Indoor
unit
Remote
controller
• Custom code setting for indoor unit
Set the DIP SW SET 3 SW1 , SW2, referring to the Table B.
SW SW SW
1 2
Table B
A (Factory setting)
DIP SW
OFF
SET 3 SW1
DIP SW
OFF
SET 3 SW2
• Do not operate any switches other than prescribed, as it can
cause the unit to operate improperly or malfunction.
En-14
Indoor unit Indoor unit
RC AD SW RC AD SW
2
2 3 4 5
2 3 4 5
A B C D
10 11 12 13
Code change
A B
A B
Dip switch "SET3"
SW
3 4
Custom code
B C
ON OFF
OFF ON
CAUTION

7.3. Function setting

• FUNCTION SETTING can be performed with the wired or
wireless remote control.
3
(The remote control is optional equipment)
• Refer to the wired or wireless remote control manual for
detailed setting information. (Set IU AD ,REF AD SW to 0)
• Refer to "7.1. Setting the address." for indoor unit address
and refrigerant circuit address settings.
• Turn the power of the indoor unit ON before starting the
setting.
6 7
6 7
* Turning on the power indoor units initializes EEV, so make
E F
sure the piping air tight test and vacuuming have been
14 15
conducted before turning on the power.
* Also check again to make sure no wiring mistakes were
made before turning on the power.
Function details
Function
Function
number
Filter
indicator
interval
C D
C D
Filter
indicator
action
Ceiling
airflow
Vertical
airflow
direction
Cool air
tem-
perature
trigger
Hot air
tem-
perature
trigger
Auto
D restart
ON
ON
External
control
Setting
Default
number
○
Adjust the filter cleaning interval
00 Default
notification. If the notification is
11
too early, change to setting 01. If
01 Longer
the notification is too late, change
02 Shorter
to setting 02.
○
00 Enable
01 Disable
Enable or disable the filter
Display
13 indicator. Setting 02 is for use
only on
with a central remote control.
02 central
remote
control
○
Regulate the airflow according
00 Default
to the needs of the installation
20
location. When set to 01, the air
High
01
flow will be stronger.
Ceiling
○
Adjust the vertical airflow
00 Default
direction. All airflow direction
23
louvers are adjusted together.
01 Raise
(Cassette type only)
○
Adjust the cool air trigger
00 Default
temperature. To lower the trigger
30
temperature, use setting 01. To
01 Adjust (1)
raise the trigger temperature, use
02 Adjust (2)
setting 02.
○
Adjust the hot air trigger
00 Default
temperature. To lower the trigger
01 Adjust (1) temperature by 6 degrees C, use
31
setting 01. To lower the trigger
02 Adjust (2)
temperature by 4 degrees C, use
setting 02. To raise the trigger
03 Adjust (3)
temperature, use setting 03.
00 Enable
Enable or disable automatic
40
system restart after a power
○
01 Disable
outage.
Allow an external controller to
○
start or stop the system, or to
00 Start/Stop
perform an emergency shutdown.
46
* If an emergency shutdown is
Emergency
01
stop
Details
performed from an external
controller, all refrigerant systems
will be disabled.