Related Manuals for Agilent Technologies Microscan 610-0002
Summary of Contents for Agilent Technologies Microscan 610-0002
- Page 1 AGILENT TECHNOLOGIES AGILENT 5DX SERIES II/2L/3 AUTOMATIC BARCODE READER INSTALLATION AND OPERATION PROCEDURES FOR THE MICROSCAN IN-LINE BARCODE READER SUBSYSTEM November 2000 © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 2 This manual has been designed to assist personnel in the installation and operation of the BCR subsystem for the AGILENT 5DX product line. Agilent Technologies provides the bar code reader, cables, connectors, power supplies and other accessories. Please verify that the following items are included with the specific product as shown below.
- Page 3 Series 3 5DX, a local power supply will have to be accessed. Connect the DC output power connector to J2 on the ADP-232 unit. Assemble the BCR as in Figure 2. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 4 “green” indicator light is lit. If the code can be read from the default settings, the "red" good read indicator light will also be lit. In addition, the BCR read head will beep continuously while reading the bar code label. Reference Figure 3 © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 5 This long beep confirms the unit has been reset. If a long beep is not generated, reconnect the jumper and repeat the procedure. When successful, reconnect the cable connector to J4 on the ADP-232 unit. Reference Figure 4 © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 6 “cfgscnr 0” (0 is for identifying a single read head). When CFGSCNR is executed, the current configuration settings will be displayed to inform the user how the scanner is being programmed. Figure 6 shows the usage and results. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 7 Distance between the reader and the barcode will affect success. Two inches is a good starting point. See Figure 8. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 8 Once a read cycle has been generated, the output will be displayed. Hit ESC to quit. Figure 9 shows the usage and output for manual alignment. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 9 Figure 9 ALIGNBCR Usage and Output for Manual Mode 8 Configure the Bar Code Reader from the Agilent 5DX User Interface. Select System > Sytem Access > Configure >5DX Options. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 10 9 Use the arrow key and select “In-Line Bar Code Reader”. Figure 11 Screen shot of result of Step 9. 10 Configure the menu to use the barcode reader and make sure the number of heads reads “1,” Save changes. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 11 Number option to match the bar code label numbers for the correct applications to be inspected. Refer to the Agilent 5DX Online Reference Guide for the procedure to set up the serial number recognition files. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 12 Figure 13 and follow the procedure below. To configure in the INSTALLATION standalone mode, refer to “MICROSCAN SERIES 600 INSTALLATION AND CONFIGURATION” on page 3 CONFIGURATION Figure 13 Model 5DX Multidrop BCR Configuration © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 13 2.0" (50mm) and verify that the raster scans across the length of the bar code label. Also check the power status “green” indicator light is lit. If the code can be read from the © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 14 When correctly executed, a single long higher pitched beep will be heard after the short beeps. This long beep confirms the unit has been reset. If a long beep is not generated, reconnect the jumper and repeat © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 15 You must hear the BCR Read Head beep. SAVE the configuration. Figure 19 shows the usage and results. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 16 9600 for a multidrop configuration because the scanner communicates directly with a concentrator and NOT the PC host. It is still possible to change the baud rate if necessary. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 17 Save and exit the file. 12 Edit ‘bcrinit.cfg”. Locate the line that reads; stand-alone =0, multidrop=1. Edit the next line down to read “Configuration=1”. See Figure 22. Save and exit the file. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 18 Distance between the reader and the barcode will affect success. Two inches distance is a good starting point. See Figure 23 below. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 19 SPACE BAR. This will allow the user to slowly control the alignment process. Once a read cycle has been generated, the output will be displayed. Hit ESC to quit. Figure 24 shows the usage and output for manual alignment. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 20 ALIGNBCR Usage and Output for Manual Mode 14 Configuration of the Bar Code Reader for the Agilent 5DX. From the Agilent 5DX User Interface select System > System Access > Configure > Options. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 21 15 Use the arrow key and select “Use serial number to find panel name.” Use arrow keys and select “In-Line Bar Code Reader.” Figure 26 Screen shot of results of Step 15. 16 To save this configuration, press the ENTER key. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 22 This is usually as far as a Customer Engineer can go without the help of the customer. The customer must provide the Serial Numbers for their boards/panels to continue with the next step. © 2000 Agilent Technologies Automatic Barcode Reader...
- Page 23 Number option to match the bar code label numbers for the correct applications to be inspected. Refer to the Agilent 5DX Online Reference Guide for the procedure to set up the serial number recognition files. © 2000 Agilent Technologies Automatic Barcode Reader...