Related Manuals for Black Box Abeo
Summary of Contents for Black Box Abeo
- Page 1 A A b b e e o o / / O O p p t t i i c c o o n n F F i i b b r r e e C C o o n n v v e e r r t t e e r r s s Abeo/Opticon Fibre Converters...
- Page 2 Abeo/Opticon Fibre Converters 1.1 About the MTU9XXX product range The Black Box MTU9XXX range of Fibre Converters provide a simple economic way of converting from one type of transmission medium to another. Examples include: Electrical signals on copper to optical signals on fibre, and vice-versa. Single-mode optical fibre to multimode and vice-versa.
-
Page 3: Table Of Contents
Abeo/Opticon Fibre Converters 1.6 Regulatory Notice The MTU9XXX range are powered by an internal mains-fed power supply. The mains input voltage is 100-250VAC, 50/400Hz. An alternative -48VDC power supply is available on all units as a custom order item. The power consumption of each model in the range is shown below, together with the current consumption over the operating voltage ranges.. - Page 4 Abeo/Opticon Fibre Converters 2. 1 MTU9XXX rear panels...
- Page 5 Abeo/Opticon Fibre Converters 2.2 Unpack and inspect the equipment. The carton should contain a single Black Box MTU9XXX model and a power cable. If there is any visible damage, do not attempt to connect the device. Contact us for advice and assistance.
- Page 6 Abeo/Opticon Fibre Converters 2.4 Power up the MTU9XXX The unit requires 100-250 VAC, 50-60 Hz AC supply. An alternative -48VDC power supply is available for all models. See Section1 for further details on power consumption. Plug an IEC mains cable into the back of the MTU9XXX and switch on. Check that the Alarm LED on the rear panel is illuminated red or green, flashing or steady.
- Page 7 Abeo/Opticon Fibre Converters 2.7 Alarm LED Status MTU9009 Fibre/Fibre Indication LED Status No mains power present Red Steady SM Alarm Red/Off Flashing Both MM and SM Alarms Green/Off Flashing MM Alarms Green Steady Status OK MTU9010/9011 Indication Fibre/BNC LED Status...
- Page 8 Abeo/Opticon Fibre Converters 3.1 MTU9200/9210/9220 set up The base panel bit-switches must be set for RJ45 or BNC connection of the E1 line and to enable the test loops which apply Outside Loop tests to both ports simultaneously. 3.2 Unbalanced BNC E1 G.703 Network port The network is connected to the BNC connectors at the rear of the unit.
- Page 9 Abeo/Opticon Fibre Converters 3.3 Balanced RJ 45 E1 G.703 Network Port Function Tx tip Tx ring Tx shield Rx tip Rx ring Rx ring Not connected Not connected 3.3.1 Connecting to a terminal device A connecting cable from the network port to a terminal port such as a router or a PABX is straight through.
- Page 10 Abeo/Opticon Fibre Converters 3.3.2 Connecting to a network device A connection from the network port to a network device such as an E1 line or an NTU requires a crossover cable. Connections are defined in the table below. DSU port...
- Page 11 Abeo/Opticon Fibre Converters 3.3.4 Cable lengths and types Cable lengths should be restricted to those defined below. Cable Max Length (metres) Belden 8132 (28 AWG) Belden 9841 (24 AWG) exceed 6dB when measured at 1 ⋅024 MHz. The frequency/attenuation characteristic of the Note: The total maximum attenuation of the cable attached to the network port must not cables attached to the network port shall follow a root frequency law.
-
Page 12: Mtu9009
Abeo/Opticon Fibre Converters 3.4 MTU9009 set-up There are no bit-switches to be set on the MTU9009, so the base label is abbreviated to basic product and serial number information together with LED status indication. SM and MM Alarms MTU9009 MM-SM SH FIBRE MEDIA CONVERTER (AC) 3.5 MTU9230 set-up... - Page 13 Abeo/Opticon Fibre Converters 3.6 Unbalanced BNC E3/DS-3 G.703 Customer Port The customer equipment is connected to the BNC connectors at the rear of the unit. Function Signal Ring Shield Cable lengths should be restricted to those defined below. E3 Max Length...
-
Page 14: Mtu9010
Abeo/Opticon Fibre Converters 3.7 MTU9010/9011 set-up There are no bit-switch settings for the unit’s normal operation. The switches are used to set up Outside Loop tests for the unit. The User (port (STM1 BNC) and the Network port (STM 1 Fibre optical) can be selected separately (i.e. not at the same time) for test action. -
Page 15: Mtu9200
Abeo/Opticon Fibre Converters MTU9200/9210/9220 Product Specifications Item Description G.703 compliant, Sensitivity - 10dB. Line coding HDB3. Bit rate: 2.048 Mbps +/- 50ppm E1 Interface Interface types: 75 Ohm unbalanced coax (BNC) or 120 Ohm balanced RJ-45 Jitter Tolerance Per G.823. - Page 16 Abeo/Opticon Fibre Converters MTU9009 Product Specifications Item Description G.957, Dual SC Multimode 62.5/125 um Bit rate: up to 155Mbps Transmit power: -14 to -19 dBm Customer Interface Max Rx input power: -14 dBm Receive sensitivity: -14 to -30 dBm Optical loss budget: = -19 - (-30) = 11dB G.957, Dual SC Single-mode 8/125 um)
- Page 17 Abeo/Opticon Fibre Converters MTU9230 Product Specifications Item Description STM-1 Electrical Interface Per G.823. Barrier EN 41003 compliant barrier provided on the E1 interface Performance PD7024 (NTR4) Diagnostics Loop Test initiated by the bit-switch G.957, Dual SC Multimode 62.5/125 um Transmit power: -14 to -19 dBm...
- Page 18 86 kPa - 106 kPa Disclaimer Black Box Network Services (UK) Ltd makes no representations or warranties with respect to the contents hereof and specifically dis-claims any implied warranties or merchantability or fitness for any particular purpose. Further, BBNS (UK) Ltd reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of BBNS (UK) Ltd to notify any person of such revision or changes.
- Page 19 Customer Support Information: FREE tech support 24 hours a day, 7 days a week: Call 0118 965 6000 Address: Black Box Network Services (UK) Ltd., 464 Basingstoke Road, Reading, Berkshire, RG2 0BG Web: www.blackbox.co.uk • E-mail: info@blackbox.co.uk © Copyright 2007. Black Box Corporation. All rights reserved.