Page 1
GETTING STARTED About the Battery System Battery Components Identify Connector Ports Install Fuses USING THE BATTERY Charge Battery Set Up Power Management MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System Model BAT24SI OPERATIONS MANUAL www.planar.com...
Page 2
Information in this document has been carefully checked for accuracy; however, no guarantee is Contents given to the correctness of the contents. This document is subject to change without notice. Planar Index provides this information as reference only. Reference to other vendors’ product does not imply any recommendation or endorsement.
QUICK LINKS Contents Safety guidelines Index The Planar battery system is designed to ensure both the highest level of product quality Regulatory Compliance and safety for the user. To maintain both quality and safety, follow the guidelines and Product Information instructions in this manual.
Page 5
Service support Warranty Other than battery installation and replacement, the Planar battery system requires no routine maintenance. Should your battery system require repair, return the unit to Planar GETTING STARTED Systems for servicing to maintain product warranty. See the About the Battery System...
About the Planar Battery System QUICK LINKS Contents The Planar Battery System, model BAT24SI, is designed specifically for point-of care Index use. It is modular, compact, and ergonomically suited for effective utilization in the medical environment. Regulatory Compliance The battery system supplies a regulated +12 VDC. It contains two sealed lead acid...
Battery Components QUICK LINKS Contents The Planar Battery System ships with all the components you need to make Index it operational. Regulatory Compliance Product Information Warranty GETTING STARTED About the Battery System Battery Components Identify Connector Ports Install Fuses USING THE BATTERY...
Set Up Power Management MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI Legend 1 Standard IEC 120–250 VAC input power 2 A, 250 V replaceable 2 USB serial port Communication channel between the power supply and...
MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI About the battery fuses The Planar Battery System requires two 6 A fuses (size 0.25 in. x1.25 in.; F type). These are available from any hardware store.
MAINTAINING THE BATTERY as the battery accepts less charge, the battery usage time decreases. Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI battery modes power consumption efficiency Charge Time Capacity of Charge 3 hours 4 hours 6 hours...
Page 11
After the power to the load is cutoff, the internal circuitry goes into sleep mode to Set Up Power Management prevent further battery discharging. The sleep mode is intended to prevent the batteries from deep discharge. MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI...
Set Up Power Management MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI Easier power management The charge level indicator is software-driven, complying with the Microsoft Windows HID Power Device Specification. You manage power consumption using the Power Options tool in the Windows Control Panel.
Page 13
Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI Recommended alarm settings • Low battery alarm – activate at 3% The alarm is triggered when the battery charge level reaches its low battery limit.
Page 14
Set Up Power Management MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI Recommended alarm notification • Low battery alarm Notification: Sound, Text Action: No action Run Program: None • Critical battery alarm Notification: None...
Page 15
Regulatory Compliance Product Information Warranty GETTING STARTED About the Battery System Battery Components Identify Connector Ports Install Fuses USING THE BATTERY Charge Battery Set Up Power Management MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SAI...
4 Use the flathead screwdriver to remove the three fuses. Make a Specifications quarter turn counterclockwise. Planar Battery System BAT24SI 2 Unplug the USB cable and the 3 Unplug the power cord. output power cable. 5 Pull out the battery tray carefully.
Page 17
3 Detach the battery cables from the four battery terminals. Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI 2 Detach the battery cables from the controller board. 4 Place the battery cables to the side and remove the used batteries. Replacement tips...
Page 18
7 Reinsert the Phillips screws on the back and front of the enclosure. Identify Connector Ports Install Fuses USING THE BATTERY Charge Battery Set Up Power Management MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI...
MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI Possible Cause AC power is not connected. Input fuse needs to be replaced. Over-temperature protection is activated. Output power cord not connected properly. Power switch is off.
Charge Battery Check with your local ordinances for proper disposal procedures. Set Up Power Management MAINTAINING THE BATTERY Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI...
Set Up Power Management MAINTAINING THE BATTERY Output Replace Battery Troubleshooting APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI • Intelligent communications (USB host) • Cooling fan • Externally accessible fuses • LED Input voltage 85 to 265 VAC Input frequency...
Page 22
Charging Charge time (new battery) APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI Sealed lead acid; quantity – 2 Yuasa NP12-12 or B and B EP12-12 Refer to the attached specification. Standard IEC power connector Standard USB cable (A male to B male)
Page 23
APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI The battery system is plugged into an AC power source. During charging mode, the attached load to the battery system is operational. The batteries charge. The cooling fan runs only when the unit is plugged into an AC power source.
Page 24
APPENDIXES Battery Disposal Specifications Planar Battery System BAT24SI The batteries are charged using a constant current/constant voltage algorithm. A constant current of 3.0 amps max is applied to each battery until the voltage on the battery reaches 14.4 V. The current exponentially decreases to maintain 14.4 V on the battery.
Systems unless directed by Planar customer service. MAINTAINING THE BATTERY Planar will validate the defect, repair the unit, and return the unit to you. The typical Replace Battery turnaround time is 10 business days.
Page 27
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. GETTING STARTED b) Repair or attempted repair by anyone not authorized by Planar. About the Battery System c) Any damage of the product due to shipment.
Page 28
Exclusion of Damages QUICK LINKS THE LIABILITY OF PLANAR IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF Contents THE PRODUCT. PLANAR SHALL NOT BE LIABLE FOR THE FOLLOWING: Index DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT,...
U.S. Federal Communications Compliance Statement Index The Planar Battery System (model BAT24SI) has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed Regulatory Compliance to provide reasonable protection against interference in a residential installation.
Page 30
(EMC) Warranty laws. Planar Systems, Inc. has made great efforts to support the medical device industry, in particular medical device manufacturers and medical device system integrators. We offer state-of-the-art systems that are compliant with worldwide accepted medical device safety...
Page 31
Symbol explanations QUICK LINKS Following are explanations of the symbols found on the Planar Battery System, Contents model BAT24SI. Index Regulatory Compliance Product Information UL 60601-1 CAN/CSA C22.2 NO.601.1 Warranty CLASS 8750 GETTING STARTED About the Battery System Battery Components...