Setup Menu; Multi-Room Setup - Pioneer Elite VSX-47TX Operating Instructions Manual

MULTI-ROOM setup

S0URCE TV
DVD/LD TV
MULTI CONTROL
VCR1/
VCR2
DVR
CD-R/
CD
TAPE1
DIMMER INPUT ATT
1 2
VIDEO SEL SIGNAL SEL
5 6
TONE BASS/TREBLE
9 0
DIRECT ACCESS DISP MODE
2
SYSTEM SETUP
MENU
TUNER EDIT
ENTER
STATUS
GUIDE
MPX
DTV ON/OFF
¶ 8
3~7
–
TUNING BAND
1 3
–
STATION DTV MENU CLASS
4 7
–
CHANNEL
2
System Setup
[Auto Surround Setup]
[1. Input Assign ]
[2. Surround Setup ]
[3. Expert Setup ]
[4. THX Audio Setup ]
3
3.Expert Setup
[1. OSD Adjustment ]
[2. Bass Peak Level]
[3. D-Range Control]
[4. Multi-Ch In Select]
[5. Function Renane]
[6. Multi-Room Setting
g]
4
4.6. Multi-Room Setting
Volume Level
[VARIABLE]
IR Receiver
[PIONEER ]
[Return]
CAUTION: If the "FIXED"
position is chosen,the
volume will be loud.
4.6. Multi-Room Setting
Volume Level
[ FIXED
IR Receiver
[PIONEER ]
[Return]
5
4.6. Multi-Room Setting
Volume Level
[VARIABLE]
IR Receiver
[ OTHERS
[Return]
6
3.6. Multi-Room Setting
Volume Level
[VARIABLE]
IR Receiver
[ OTHERS ]
[Return]
CAUTION: If the "FIXED"
position is chosen,the
volume will be loud.
1 Turn on the receiver, your TV and
SETUP
SYSTEM RECEIVER
OFF
2 Press the SYSTEM SETUP button
SAT TV CONT
MULTI
VIDEO
OPERATION
1
TUNER RECEIVER
LOUDNESS SPEAKER A/B
3 4
TAPE 2 EFFECT/CH SELL
7 8
– + +
10 DISC
3 Use the 5∞ buttons to select
ENTER
REMOTE SETUP
EXIT
RETURN
EXTRA MENU
+
TUNING
¡
4 Select the VOLUME LEVEL by
+
STATION
¢
+
CHANNEL
]
5 Select the IR RECEIVER type.
6 Select RETURN (use ∞5) then press
]
7 Use the ∞5 buttons to select
]
press RECEIVER on the remote
control.
Make sure your TV is set to the receiver.
then select EXPERT SETUP using 5
and ∞. Press ENTER.
The EXPERT SETUP menu appears on the OSD.
MULTI-ROOM SETTING . Press
ENTER.
selecting VARIABLE or FIXED.
If you hook up a just a power amplifier in the sub room
the VSX-47TX will act as a pre-amp. In this case
choose VARIABLE for the VOLUME LEVEL setting. If
you hook up a full integrated amplifier in the sub room
(such as another Pioneer VSX receiver) choose FIXED
for the VOLUME LEVEL setting.
CAUTION!
If the MULTI ROOM is set to FIXED the volume on the main
unit will be set to maximum. Thus, when output, it will be
extremely loud. Please set the master volume controls of the
integrated amplifier in the sub room very low at first and ex-
periment to find the correct volume.
If you have an IR receiver from a different company
than PIONEER, select OTHERS. If you have the
Pioneer-made MR-100, or the IR receiver you're using
doesn't seem to work after selecting OTHERS, select
PIONEER.
ENTER to go back to the EXPERT

SETUP menu.

RETURN and press ENTER, again.
Then use the ∞5 buttons to select
EXIT and press ENTER.
There may be some IR receivers that can't be
memo
used with this receiver. Check with a PIONEER
representative to be sure.
Using Other Functions
75