Regulatory Information - Microsoft C3K1383 Getting Started

● Do not allow minors to use a pointer unsupervised. Laser pointers are not toys.
● Do not point a laser pointer at a mirror-like (reflective) surface. A reflected beam can act like a direct beam on the eye.
● Do not disassemble the device.
● Do not use the device outside of its specified operating temperature range +41ºF (+5ºC) to +95ºF (+35ºC). If the device is
exposed to an environment outside of its prescribed operation, turn off the device and allow the temperature to stabilize
within the specified operating range before using the device.
All Devices
Choking Hazard
This device may contain small parts which may be a choking hazard to children under 3. Keep small parts away from children.
Do Not Attempt Repairs
Do not attempt to take apart, open, service, or modify the hardware device or power supply. Doing so could present the
risk of electric shock or other hazard. Any evidence of any attempt to open and/or modify the device, including any peeling,
puncturing, or removal of any of the labels, will void the Limited Warranty.
Usage and Cleaning
Use in accordance with these instructions:
● Do not use near any heat sources.
● Only use attachments/accessories specified by Microsoft.
● Clean only with dry cloth.
Keeping Cables Out of the Way of People and Pets
Arrange all cables and cords so that people and pets are not likely to trip over or accidentally pull on them as they move around
or walk through the area. When the product is not in use, you may need to disconnect all cables and cords from the front and
rear of the product to keep them out of the reach of children and pets. Do not allow children to play with cables and cords.
Laser and LED Specifications
Caution Use of controls or adjustments, or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
Laser Devices
This device complies with International Standard IEC60825-1:1993+A1+A2 (IEC 60825-1:2001-08) for a Class 1 and Class 2 laser
product. This device also complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50,
dated June 24, 2007.
Class 1 Laser Devices
Beam description: Collimated (parallel) beam of infrared light (invisible to the user)
Laser power output: < 716 microwatts (at 832 nanometers) to 834 microwatts (at 865
nanometers)
Emitted laser wavelength: nominal: 850 nanometers, range: (832 – 865 nanometers)
A Class 1 laser product is safe under reasonably foreseeable conditions of operation as
described by IEC 60825-1 and 21 CFR 1040.10. However, it is recommended that you not direct
the laser beam (which is emitted from the bottom of the device) at anyone's eyes.
Class 2 Laser Devices
Beam description: Collimated (parallel) beam of light
Laser power output: < 1 milliwatt
Emitted laser wavelength: 630 – 670 nanometers
This optical device has no serviceable parts. The Class 2 laser beam is emitted
from the front of the device.
Optical (LED) Mouse
This product has been evaluated to comply with International Standard IEC60825-1:1993+A1+A2
(IEC 60825-1:2001-08).
This product uses LEDs that are considered Class 1 (IEC60825-1:1993+A1+A2).
LED output power: < 67.8µW (photochemical limit), < 4.2mW (thermal limit)
LED nominal wavelength: 470nm (blue), 635nm (red)
A Class 1 product is safe under reasonably foreseeable conditions of operation as described by IEC 60825-1. However, it is
recommended that you not direct the light (which is emitted from the bottom of the device) at anyone's eyes.
This optical device has no serviceable parts.

Regulatory Information

Tested to comply with FCC (U.S. Federal Communications Commission) Standards. For home or office use. Not intended for use
in machinery, medical, or industrial applications. Any changes or modifications not expressly approved by Microsoft could void
the user's authority to operate this device. This product is for use with NRTL-Listed (UL, CSA, ETL, etc.), and/or IEC/EN 60950
compliant (CE marked) Information Technology equipment. No serviceable parts included.
This device is rated as a commercial product for operation at +41ºF (+5ºC) to +95ºF (+35ºC).
For detailed information on U.S. and Canadian radio interference regulations, search for "regulations" in on-screen Help
installed with the software.
CLASS 1
LASER PRODUCT
IEC 60825-1:2001-08
Class 1 LED product
5