Raymarine Ray50 Mounting And Getting Started
Vhf marine radio
Hide thumbs
Also See for Ray50:
- Installation and operation instructions manual (116 pages) ,
- Mounting and getting started (27 pages) ,
- Troubleshooting manual (60 pages)
Related Manuals for Raymarine Ray50
Summary of Contents for Raymarine Ray50
- Page 1 Ray50 / Ray60 / Ray70 Mounting a nd Ge tting S ta rte d MULTILINGUAL Da te : 09-2014 Docume nt numbe r: 88xxx-1-EN © 2014 Ra yma rine UK Limite d...
- Page 2 ENGLISH Document n umber: 88033-0.1 Date: 09-2014...
- Page 3 I h ave <state number o f p ersons on board and any your p roduct, p lease refer t o the expanded other i nformation — drifting, fl ares fired etc.> handbook, a vailable on the Raymarine website (www.raymarine.com). I R EQUIRE IMMEDIATE ASSISTANCE...
-
Page 4: Water Ingress
Perform regular r adio checks when using Disclaimer your v essel, a s recommended in radio Raymarine does not w arrant t hat t his product i s training and certification schemes and error-free or t hat i t i s compatible with products radio equipment r ules of u se. -
Page 5: Compliance Statement ( Part 1 5.19)
(2) l'utilisateur 2. This device must a ccept a ny interference received, Additional i nformation – Ray50 de l'appareil doit accepter tout brouillage including interference that m ay cause undesired The following additional information is required for radioélectrique subi, même si le brouillage... - Page 6 ATIS adds data at the end of radio transmissions that Maritime Mobile Service Identity (MMSI) • Raymarine equipment and cables connected to it are: identifies your station. ATIS operation can be turned on or off as needed via the radio’s menu.
-
Page 7: Applicable Products
(IMO) and Safety of Life at Sea (SOLAS) Carriage Requirement for ferrites on non-Raymarine cables Regulations. • Passive If your Raymarine equipment is to be connected to other speaker equipment using a cable not supplied by Raymarine, a Technical accuracy... -
Page 8: Location And Mounting
Ensure that the antenna is connected to the radio before transmission. Ventilation requirements Raymarine declares a Maximum Permissible Exposure To provide adequate airflow: (MPE) radius of 1.5 metres (4.9 ft) (per OET Bulletin 65) for this system, assuming 23 watts output to an •... -
Page 9: Product Dimensions
Fistmic dimensions The Ray60 and Ray70 can be flush mounted or bracket Ray50 dimensions mounted. The Ray50 can be flush mounted or bracket mounted. Ray60 and Ray70 Flush mount dimensions Ray50 Flush mount dimensions 168 mm (6.6 in.) 199 mm (7.8 in.) 156 mm (6.1 in.) -
Page 10: Bracket Mounting
Dxxxxx-1 Removing the mounting hole covers 1. Using a drill and a 4 mm (5/32) drill bit, drill out the Before the Ray50 can be flush mounted the mounting 4 mounting holes. hole covers must be removed. Holes should be drilled from the front of the unit, taking care not to damage the unit by applying too much force to the drill. - Page 11 11. Attach the mounting hole covers. Dxxxxx-1 1. Using a drill and a 4 mm (5/32) drill bit, drill out the 4 mounting holes. Holes should be drilled from the front of the unit, Dxxxxx-1 taking care not to damage the unit by applying too Dxxxxx-1 1.
- Page 12 11. Attach the front bezel. ii. Inner edges - ensure that the bezel sits flat. 4. Check that all control buttons are free to operate. Ray50 / Ray60 / Ray70...
-
Page 13: Power Connection
Dxxxxx-1 then please consult a Raymarine authorized dealer for 4. Product power cable 1. Base station support. 5. Vessel battery... - Page 14 SeaTalk ng® connection In-line fuse and thermal breaker ratings Circuit breaker The following in-line fuse and thermal breaker ratings The product can interface with Raymarine ® Fuse apply to your product: or GNSS receivers and Raymarine ® multifunction displays using the SeaTalk ng®...
-
Page 15: Nmea 0183 Connection
Controls and interface 3. Fully insert the spur cable connector into the 1. PTT (Push to Talk) — Press and hold to send a SeaTalk ng® connector on the unit. voice message. Release to return to receive mode. The controls and interface available are as follows: 4. -
Page 16: Powering The Unit Off
• INT — International which decreases • CAN — Canada receiver sensitivity in high traffic areas to • WX — Weather decrease unwanted reception Note: Special licensing is required to receive USA and Canadian channel sets. Ray50 / Ray60 / Ray70... - Page 17 Symbol Name Description 1. Currently selected menu item Symbol Name Sub-options 2. Scroll bar Indicates that a DSC • Hailer call has been received Hail/Fog/Intercom 3. Menu items • Fog horn The main menu includes the following items: • Intercom Symbol Name Sub-options...
-
Page 18: Shortcut List
Contrast to the desired level. pre-programed in MARCOM-C mode. See 4. Press the Power button again to return to the Changing the radio region for more information. previous screen. Ray50 / Ray60 / Ray70... -
Page 19: Selecting A Network Type
1. Select Set-up. ATIS ID in your product, it will have to be been set. 2. Select Network type. reset by an authorized Raymarine ® dealer. 4. Use the Rotary knob to cycle through the available numbers and press OK to confirm each number and The following network types are available: move to the next digit. -
Page 20: Entering Your Atis Id
6. Press the Back button at any time to edit digits you have already entered. With the spring loaded cover open: 7. Press and hold the OK button to display options to Move cursor back and forward through the digits. Ray50 / Ray60 / Ray70... -
Page 21: Making A Mayday Call
Making a Mayday call Cancelling a distress call after transmission In an emergency you can use your unit to make a Mayday call. A distress call can be cancelled after it has been 1. Press the 16 PLUS button. transmitted. 55 60 5 2. -
Page 22: Acknowledging A Distress Call
9. Press and hold the PTT button and speak your 1. Switch to channel 16 to listen for the distress voice message. message. 10. Release the PTT button when you have completed 2. Wait for the CRS to acknowledge the call. your message. Ray50 / Ray60 / Ray70...