Advertisement
Advertisement
Table of Contents
Related Manuals for Craig CHT923
Summary of Contents for Craig CHT923
- Page 2 FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
- Page 4 Insert the small plug from supplied AC/DC adaptor to DC IN jack on the rear of the unit and insert the AC/DC adaptor to the wall outlet having AC 100-240V~, 50/60 Hz. NOTE:This AC/DC Adapter is intended to be AC/DC adapter correctly orientated in a vertical or floor mount position.
- Page 5 2.1 Mounting on the wooden wall You may use 2 pieces screws (Included) 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill the supplied screws directly into the marks that you have made on the wall and leave approx.
-
Page 6: Front View
Front View 1.Remote Sensor 2. LCD Display 3.Speakers Top View and Back View DC IN 16V, 3A AUX 2 AUX 1 SOURCE DC IN 16V, 3A AUX 2 AUX 1 SOURCE 4. DC IN jack ( Mute ) button 6. SOURCE button Standby button 8. - Page 7 TUNE- TUNE+ SLEEP MO/ST SOURCE CLOCK VOL- BASS - TREBLE- BASS+ TREBLE+ VOL+ 9. BASS +/- 1. CH+/ ( Channel Up ) Power ( Mute ) 3. TUNE + / ( Tune or Skip Forward ) 11. EQ ( Equalizer ) 12.
-
Page 8: Battery Precautions
-First Time Use Remove and discard the insulation tab as figure on the right -Replacing Batteries For Remote Control 1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. -
Page 9: General Operations
GENERAL OPERATIONS TIME SET OR RESET: 1. Connect the unit to the power as previous procedures. The LCD Display will turn on. 2. Make sure the unit is in Standby mode, then press and hold the CLOCK button on the remote control. The digit of hour will blink. 3. -
Page 10: Listen To Fm Radio
GENERAL OPERATIONS 1. Connect the AC/DC adapter to the unit and wall outlet as the previous procedure . The LCD display will turn on. 2. Press the Power button on the unit or remote control to power on the unit from standby mode. 3. - Page 11 ( For details pairing procedures, please refer to the user's manual of your BT Device.) Notes: 1. When the external BT player searched the unit, our model number "CHT923" will appear on the display of external BT device. 2. Pairing code "0000" may need to enter. Normal operation after paired: 1.
- Page 12 AUX 1 : LISTEN TO TV/DVD/VCR/DVR 1. Connect the Aux out jacks from the external audio player (such like TV, DVD player, VCR …etc.) to the AUX 1 jacks on the rear of unit by the supplied RCA Connection Cable as the figure below: white To Audio Out Jacks DC IN...
-
Page 13: Troubleshooting Guide
TROUBLESHOOTING GUIDE Check the followings before requesting service SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTION Power AC/DC adapter Connect the power AC/DC adapter not connected No power The unit is in Standby mode Press button to turn on the unit Raise volume level by pressing the VOL Volume in minimum position (Volume) + button Play the music/movie in the connected... - Page 14 Power Source..................DC 16V; 3A, Radio Coverage.....................FM 87.5 -108.0 MHz Impedance of Speakers: ................8 Ohm,10 W x 2 Loud Speakers Woofer ................... 8 Ohm,15 W x 2 Bluetooth Effective Range in Open Aera..............Up to 32 feet Remote Effective Range..................Up to 16 feet 1 x AC/DC Adaptor ( Input: AC 100-240V~ 50/60Hz;...
-
Page 15: Limited Warranty
Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state.