Hilti SBT 4-A22 Manual
Hide thumbs
Also See for SBT 4-A22:
- Original operating instructions (202 pages) ,
- Manual (212 pages) ,
- Manual (76 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hilti SBT 4-A22
Summary of Contents for Hilti SBT 4-A22
- Page 1 SBT 4-A22 English Printed: 29.08.2017 | Doc-Nr: PUB / 5356251 / 000 / 01...
- Page 2 Printed: 29.08.2017 | Doc-Nr: PUB / 5356251 / 000 / 01...
-
Page 3: Table Of Contents
Contents Information about the documentation ........About this documentation . -
Page 4: Information About The Documentation
Direct current (DC) 1.4 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. -
Page 5: Declaration Of Conformity
▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Drill/driver SBT 4A22 Generation Serial no. -
Page 6: Drill Safety Warnings
▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Power tool use and care ▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. - Page 7 ▶ Before beginning the work, check the hazard classification of the dust that will be produced. Wear respiratory protection of a type suitable for the dust you are exposed to and use an industrial vacuum cleaner with an officially approved protection classification in accordance with locally applicable dust protection regulations.
-
Page 8: Description
3 Description 3.1 Product overview Side handle Keyless chuck English Printed: 29.08.2017 | Doc-Nr: PUB / 5356251 / 000 / 01... -
Page 9: Intended Use
Troubleshooting section. 3.4 Items supplied Drill / driver, operating instructions. • Other system products approved for use with this product can be found at your local Hilti Center or online at: www.hilti.group 4 Technical data 4.1 Drill/driver Rated voltage 21.6 V... -
Page 10: Noise Information And Vibration Values In Accordance With En 60745
4.2 Noise information and vibration values in accordance with EN 60745 The sound pressure and vibration values given in these instructions have been measured in accordance with a standardized test and may be used to compare one power tool with another. They may be used for a preliminary assessment of exposure. -
Page 11: Removing The Battery
▶ Push the battery into the tool from the rear until it engages with an audible click. 5.1.2 Removing the battery ▶ Remove the battery. 5.1.3 Fitting and adjusting the side handle CAUTION Risk of injury. The drill/driver may start inadvertently. ▶... -
Page 12: Fitting The Accessory Tool
5.1.4 Fitting the accessory tool 1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 2. Check that the connection end of the accessory tool is clean. Clean the connection end if necessary. 3. -
Page 13: Selecting The Gear
▶ Set the forward/reverse switch to the desired direction of rotation. 5.2.2 Selecting the gear ▶ Select the gear. 5.2.3 Switching on ▶ Press the control switch. Note Speed can be controlled steplessly right up to maximum by varying how far the control switch is pressed in. -
Page 14: Care And Maintenance Of Cordless Tools
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com... -
Page 15: Troubleshooting
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information. -
Page 16: Manufacturer's Warranty
▶ Disposal of electric tools or appliances together with household waste is not permissible. 10 Manufacturer’s warranty ▶ Please contact your local Hilti representative if you have questions about the warranty conditions. English Printed: 29.08.2017 | Doc-Nr: PUB / 5356251 / 000 / 01... - Page 17 Printed: 29.08.2017 | Doc-Nr: PUB / 5356251 / 000 / 01...
- Page 18 Hilti = registered trademark of Hilti Corp., Schaan 20170510 Printed: 29.08.2017 | Doc-Nr: PUB / 5356251 / 000 / 01...