Table of Contents
Advertisement
Alarm Mode
Mode indicator
Melody name
Alarm number
Hour
You can set up to five melody alarms. When a Daily Alarm is turned on, its
melody alarm sounds for about 20 seconds at the preset time each day. In the
Timekeeping Mode, press any button (except E E E E E ) to stop the melody alarm after
it starts to sound. Pressing E E E E E while a melody is playing toggles the display
between an animated character and the name of the melody that is playing.
When the Hourly Time Signal is turned on, the watch beeps every hour on the
hour.
To set the alarm time
1. While in the alarm Mode, press D D D D D to display the alarm number you want to
set.
Alarm 1
Alarm 2
Alarm 3
SIG: 00 (Hourly Time Signal)
2. Hold down A A A A A until the melody setting starts to flash on the display, indicating
the setting screen. The alarm is automatically turned on at this time.
3. Press C C C C C to change the selection in the sequence shown below.
Melody Setting
4. While melody setting is selected, use D D D D D or B B B B B to scroll through melody names.
Setting
Ramdom play of melodies 1, 2, 3, 4 and 5
– 0
Melody 1
– 1
Press
.
Melody 2
– 2
Melody 3
– 3
Melody 4
– 4
Press
.
Melody 5
– 5
Beeper
–
See the "MELODY LIST" at the back of this manual for the names of
melodies.
Some melody alarms tune names may be displayed in abbreviated format.
• While any other setting is selected, press D D D D D to increase it or B B B B B to decrease it.
Holding down either button changes the setting at high speed.
5. After you make the settings you want, press A A A A A to exit the setting screen.
• The format (12-hour and 24-hour) of the alarm time matches the format you
select for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the
time correctly as morning or afternoon.
To stop a melody alarm
• Press any button (except E E E E E ) to stop a melody alarm after it starts to sound.
To turn a daily Alarm or the Hourly Time Signal on and off
1. Use D D D D D to display the alarm you want to turn on or off, or the screen for
turning the Hourly Time Signal on or off.
2. Press B B B B B to toggle the displayed alarm or Hourly Time Signal on and off.
• Alarm indicator 1 is displayed in the alarm mode
Alarm indicator 1
only. It indicates the on/off status of the currently
displayed alarm only. Note that this indicator is
used for different purposes in other modes.
• Alarm indicator 2 is displayed in all modes when
any of the five alarms is turned on.
• Alarm indicator 3 is displayed in the Alarm Mode
only. It shows on when the currently displayed
alarm is on, and OF when the currently displayed
Alarm indicator 3
Alarm indicator 2
alarm is off.
Hourly Time Signal
• Hourly Time Signal indicator 1 is displayed in the
indicator 1
Alarm Mode only when the Hourly Time Signal is
turned on. Note that this indicator is used for
different purposes in other modes.
• Hourly Time Signal indicator 2 is displayed in all
modes when the Hourly Time Signal is turned on.
• Hourly Time Signal indicator 3 is displayed in the
Alarm Mode only. It shows on when the Hourly
Time Signal is on, and OF when the Hourly Time
Signal is off.
To test the alarm
In the Alarm Mode, display the alarm you want to
Hourly Time Signal
sound, and then press E E E E E to play its melody or beep.
indicator 3
You can also press E E E E E to play an alarm's melody while
setting the alarm time.
Hourly Time Signal
• To stop a playing melody or beep, press any button.
indicator 2
Current time
Minutes
Alarm 4
Alarm 5
Hour
Minutes
Alarm Sound
— 3 —
Stopwatch Mode
The stopwatch Mode lets you measure elapsed time,
Mode indicator
split times, and two finishes. The range of the
Current time
stopwatch is 23 hours, 59 minutes, 59.99 seconds.
You can use the EL backlight by pressing E E E E E at any
time while the stopwatch is operating.
Hours
Minutes
Seconds
1/100 second
Elapsed time measurement
Stop
Re-start
Start
Split time measurement
Split
Split release
Start
Split time and 1st-2nd place times
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Record time of
first runner.
Memo Mode
The Memo Mode lets you store up to five memos,
Mode indicator
each with an eight-character title and 16 characters
of data.
Title
Recalling a Memo
In the Memo Mode, press D D D D D to scroll through the
Memo titles. When you find the title you want, press
B B B B B , and the screen alternates between the title and
data.
• The display can show only five characters at a time.
Longer text scrolls continuously from right to left.
The symbol "
to the left is the last, and the character or digit to
the right is the first.
• A series of hyphens " – – – – – " is displayed for a
memo that does not contain any data.
Memo number
To input a memo
1. In the Memo Mode, press D D D D D to display the memo number you want to set.
2. Hold down A A A A A until the first (leftmost) character of the memo title starts to
flash on the display. This indicates the input screen.
3. Press C C C C C to move the flashing in the sequence shown below. Press E E E E E to move
the flashing in the opposite direction.
Press
.
Press
.
Title Character 1
Data Character 16
4. Use D D D D D or B B B B B to scroll through characters at the current location of the flashing.
Holding down either button scrolls at high speed.
Press
.
Press
.
Space
A to Z
Hyphen
Numbers
See the "CHARACTER LIST" at the back of this manual for details.
• Pressing D D D D D and B B B B B at the same time while inputting memo title or data clears
all title and data. At this time the message "CLEAR" appears on the display.
5. After you input the data you want, press A A A A A to exit the input screen.
Stop
Clear
Stop
Clear
Split release
Clear
Record time of
second runner.
" indicates that the character or digit
Title Character 8
Data Character 1
Punctuation
Japanese
characters
Symbols
Advertisement
Table of Contents
