Table of Contents
Advertisement
2. OPERATION CHART: QW-2489
General Guide
• Press C C C C C to change from mode to mode.
• Pressing E E E E E in any mode besides the Alarm Mode illuminates to the display for
about three seconds. The backlight is disabled while a setting screen is on
the display.
Timekeeping Mode
Press C C C C C .
Timekeeping Mode
Press D D D D D to toggle between 12-hour and 24-hour
Month
Day
timekeeping.
Day of week
• With 12-hour timekeeping, times between midnight
and noon are indicated by A (am), while times
between noon and midnight are indicated by P
(pm).
• The A and P indicators do not appear for 24-hour
timekeeping.
• Pressing B B B B B plays a randomly selected melody. To
stop a playing melody, press any button besides E E E E E .
• Pressing E E E E E while a melody is playing toggles the
display between an animated character and the
Seconds
Hour
name of the melody.
Minutes
• Press E E E E E to illuminate the display for about three
PM indicator
seconds. When 12-hour timekeeping is being used,
pressing E E E E E also displays an animated character.
DST indicator 2
Timekeeping Mode Settings
In addition to settings for the current time and date, the Timekeeping Mode
setting screen also lets you turn button tones and melody play on and off,
adjust tones and melody volume, and adjust display contrast.
To make Timekeeping Mode settings
1. While in the Timekeeping Mode, hold down A A A A A until the second's digits flash
on the display, indicating the setting screen.
2. Press C C C C C to move the flashing in the sequence shown below. Press E E E E E to move
the flashing in the opposite direction.
Press
.
Press
.
Seconds
DST
Contrast
Volume
(CNT)
(VOL)
3. While the second's setting is selected (flashing),
DST indicator 1
press D D D D D or B B B B B to reset it to 00.
• If you press D D D D D or B B B B B while the second's setting is in
the range of 30 to 59, the seconds are reset to 00
and 1 is added to the minutes. If the second's
setting is in the range of 00 to 29, the minute's
count is unchanged.
• While the DST (Daylight Saving Time) setting is
selected, press D D D D D or B B B B B to toggle it on and off.
• DST indicator 1 is displayed in the Timekeeping
Mode setting screen only when the DST setting is
selected. It shows ON when the DST setting is on,
and OFF when the DST setting is off.
• DST indicator 2 is displayed in the Timekeeping
DST indicator 2
Mode, Day Counter Mode and Alarm Mode when
the DST setting is turned on.
* Daylight Saving Time (DST), which is also sometimes called "summer time"
advances the time for one hour, as is the custom in some areas during the
summer. Remember that not all countries or even local areas use Daylight
Saving Time.
• While the SOUND (button tones) setting is selected, press D D D D D or B B B B B to turn the
beep and musical tone on and off, as shown below.
• Changing the SOUND also changes the Hourly Time Signal tones.
Press
.
Press
Musical tone
Beep
• While the VOL setting is selected, press D D D D D or B B B B B to toggle it between loud and soft.
Press
Loud
• With some models, changing the volume setting affects volume very little.
• While the CNT setting is selected, press D D D D D to make the display darker, or B B B B B to
make it lighter.
• While any other setting is selected (flashing), press D D D D D to increase it or B B B B B to
decrease it. Holding down either button changes the setting at high speed.
4. After you make the settings you want, press A A A A A to exit the setting screen.
• The day of the week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 2000 to December 31, 2039.
• The watch's built-in full automatic calendar automatically makes allowances
for different month lengths and leap years.
Once you set the date, there should be no reason to change it except after
the replacement of the watch's battery.
Day Counter Mode
Hour
Minutes
Year
Sound
Day
Month
(SOUND)
.
Off
or
.
Soft
• If you do not perform any operation for a few minutes while a setting screen (with
flashing digits) is on the display, the watch automatically exits the setting screen.
• If you do not perform any operation for a few minutes in any mode besides
stopwatch mode, the watch automatically reverts to the normal timekeeping
screen.
Alarm Mode
About the Backlight
Pressing E E E E E in any mode besides the Alarm Mode illuminates the display for
about three seconds. The backlight is disabled while a setting screen is on the
display.
• The backlight of this watch employs an electro-luminescent (EL) light, which
loses its illumination power after very long term use.
• Frequent use of the backlight shortens battery life.
• The illumination provided by the backlight may be hard to see when viewed
under direct sunlight.
• The backlight automatically turns off an alarm sounds.
• The watch emits an audible sound whenever the display is illuminated. This
does not indicate malfunction.
Day Counter Mode
Mode indicator
Day counter
record number
Number of days
The Day Counter Mode lets you count the number of days from the
Timekeeping Mode's current date to a specific target date.
• There are five Day Counter records, each of which can be assigned up to 12
characters of text and a target date.
• When a target date is reached, the DAYS indicator flashes on the display in
the Timekeeping Mode. The DAYS indicator also flashes in the Day Counter
Mode when the screen for the target date is on the display.
• The DAYS indicator flashes on the target date each year, regardless of the
year setting of the target date.
• The initial default date for a Day Counter record is 2001/1/1, and the text area
contains All spaces. (All spaces for the text display a series of hyphens " – – –
– – ".)
Recalling Day Counter Data
In the Day Counter Mode, press D D D D D to scroll through the Day Counter record
screens.
• The day count is a negative value whenever the target date comes before the
current date.
To set the target date
1. In the Day Counter Mode, press D D D D D to display a record number you want to
set.
2. Hold down A A A A A until the first (leftmost) text character starts to flash on the
display. This indicates the input screen.
3. Press C C C C C to move the flashing in the sequence shown below. Press E E E E E to move
the flashing in the opposite direction.
Press
.
Press
Character 1
Day
4. While the flashing is located within the text area, use D D D D D or B B B B B to scroll through
characters at the current location of the flashing. Holding down either button
scrolls through characters at high speed.
Press
.
Press
.
Space
A to Z
Hyphen
Numbers
See the "CHARACTER LIST" at the back of this manual for details.
5. While any other setting is selected, press D D D D D to increase it or B B B B B to decrease it.
Holding down either button changes the setting at high speed.
• Pressing D D D D D and B B B B B at the same time while the flashing is located within the text
area clears any input text and resets the date setting to the current date. At
this time the message "CLEAR" appears on the display.
• Pressing D D D D D and B B B B B at the same time while the flashing is located within the
date area resets the date setting to the current date without affecting the text.
6. After you make the settings you want, press A A A A A to exit the input screen.
• The date can be set within the range of January 1, 1940 to December 31,
2039.
— 2 —
Stopwatch Mode
Memo Mode
Text
Year
Month
Target Date
Day
DAYS indicator
.
Character 12
Month
Year
Punctuation
Japanese
characters
Symbols
Advertisement
Table of Contents
