Page 1
MTM700 TETRA Mobile Radio 380-430 MHz (MT912) 806-870 MHz (MT712) Detailed Service Manual Part Number: 6866534D19-A @6866534D19@ WLS EMEA / European Publications Department Berlin, 6866534D19-A, Issued: 02.2003...
DOCUMENT HISTORY MTM700 Mobile Radio / Detailed Service Manual DOCUMENT HISTORY The following major changes have been implemented in this manual since the previous edition: Edition Description Date 6866534D19-O Initial edition Dec. 2001 6866534D19-A Update for Rev B and Rev C Radio Tanapas Feb.
Page 4
MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
C a u t i o n INTERNATIONAL STANDARDS. Compliance with RF Energy Exposure Standards Your Motorola radio is designed and tested to comply with a number of national and international standards and guidelines regarding human exposure to radio frequency electromagnetic energy, including: •...
MTM700 Mobile Radio / Detailed Service Manual Product Safety and RF Exposure COMPLIANCE AND CONTROL GUIDELINES AND OPERATING INSTRUCTIONS FOR MOBILE RADIOS To ensure optimal performance and compliance with the RF energy exposure limits in the above standards and guidelines, always adhere to the following procedures: Transmit and Receive •...
Product Safety and RF Exposure MTM700 Mobile Radio / Detailed Service Manual • Use only Motorola approved supplied antenna or Motorola approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate RF exposure guidelines. •...
MTM700 Mobile Radio / Detailed Service Manual Product Safety and RF Exposure 2. Before installing the radio, determine the location of the electronic control modules and their harnesses in the vehicle. 3. Route all radio wiring, including the antenna transmission line, as far away as possible from the electronic control units and associated wiring.
Product Safety and RF Exposure MTM700 Mobile Radio / Detailed Service Manual ADDITIONAL IMPORTANT INFORMATION FOR SERVICING AND INSTALLING THE RADIO C a u t i o n Only specialized workshops should be contacted for installation, maintenance and repair work.
Page 10
MTM700 Mobile Radio / Detailed Service Manual Product Safety and RF Exposure THIS PAGE INTENTIONALLY LEFT BLANK...
CONTENTS MTM700 Mobile Radio / Detailed Service Manual CONTENTS COPYRIGHT COMPUTER SOFTWARE COPYRIGHTS Trademarks ..........ii...
Page 12
MTM700 Mobile Radio / Detailed Service ManualCONTENTS CONTENTS CHAPTER 4 THEORY OF OPERATION Section Introduction ........4 - 1 CHAPTER 4.1...
Page 13
CONTENTS MTM700 Mobile Radio / Detailed Service Manual xiii Receiver Path ........4.2 - 5 Transmitter Path .
Page 14
MTM700 Mobile Radio / Detailed Service ManualCONTENTS CONTENTS Power Supplies ........4.3 - 8 Volume Control / ON/OFF Switch .
Page 15
CONTENTS MTM700 Mobile Radio / Detailed Service Manual CHAPTER 7 MAINTENANCE Introduction ..........7 - 1 Preventive Maintenance .
Page 16
MTM700 Mobile Radio / Detailed Service ManualCONTENTS CONTENTS Main Board 8466519A01_O / POWER_AMP_LNODCT . . . 8.1.1 - 17 PCB / HDI_Controller 8466520A01_O / BOT&TOP SIDE . . 8.1.1 - 18 HDI_Controller 8466520A01_O (Sheet 1) ....8.1.1 - 19 HDI_Controller 8466520A01_O (Sheet 2) .
Page 17
CONTENTS MTM700 Mobile Radio / Detailed Service Manual xvii PCB / HDI_Controller 8466520A01_O / BOT&TOP SIDE . . 8.2.1 - 18 HDI_Controller 8466520A01_O (Sheet 1) ....8.2.1 - 19 HDI_Controller 8466520A01_O (Sheet 2) .
Page 18
MTM700 Mobile Radio / Detailed Service ManualCONTENTS CONTENTS CHAPTER 9 TROUBLESHOOTING Section Introduction ........9 - 1 General .
Page 19
CONTENTS MTM700 Mobile Radio / Detailed Service Manual APPENDIX A CONNECTOR PIN FUNCTIONS ....A -1 Transceiver Rear - Pin Function ......A -1 Transceiver Front - Pin Function .
Page 20
MTM700 Mobile Radio / Detailed Service Manual CONTENTS THIS PAGE INTENTIONALLY LEFT BLANK...
SCOPE & WARRANTY INFORMATION MTM700 Mobile Radio / Detailed Service Manual 1 - 1 CHAPTER 1 SCOPE & WARRANTY INFORMATION SCOPE OF THIS MANUAL This manual is intended for use by service technicians familiar with similar types of equipment. It contains information required for the installation of the equipment described and is current as of the printing date.
1 - 2 MTM700 Mobile Radio / Detailed Service Manual SCOPE & WARRANTY INFORMATION Manuals & User Guides Radio Installation Instructions 6866534D67MTM700 Radio Installation Instructions (English) Service Manuals 6866534D19MTM700 Detailed Service Manual (English) 6804112J73MTM700 Detailed Service Manual (Mandarin) 6866534D20MTM700 Basic Service Manual (English)
"return for repair" warranty, a check of the product should be performed prior to shipping the unit back to Motorola. This is to ensure that the product has been correctly programmed or has not been subjected to damage outside the terms of the warranty.
Page 24
1 - 4 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
MTM700 Mobile Radio / Detailed Service Manual 2 - 1 CHAPTER 2 MODEL INFORMATION & ACCESSORIES MTM700 Mobile Radio Model Information This manual applies to the following MTM700 Mobile Radio Models Type No. Sales Model No. Short Description Model MT912...
2 - 2 MTM700 Mobile Radio / Detailed Service Manual MODEL INFORMATION & ACCESSORIES MTM700 Model Specifications GENERAL RECEIVER TRANSMITTER π ETSi: ETS 300 394-1 Receiver Type: Superheterodyne Modulation Type: /4DQPSK Type Number: Frequency Range: RF Power: 380-430 MHz MT912...
Dash/Desk Mount with MTM700 Mobile Radio (380-430MHz) with Direct Mount Control Head, Speaker, Microphone or Handset, Standard User Guide, and Installation Accessories. Remote Mount with MTM700 Mobile Radio (380-430MHz) with Remote Mount Control Head, optional either with remote mount front housing or expansion control head, Speaker, Microphone or Handset, Remote Mount cables, Standard User Guide, and Installation Accessories.
Page 28
2 - 4 MTM700 Mobile Radio / Detailed Service Manual MODEL INFORMATION & ACCESSORIES MTM700 ACCESSORIES 380-430 MHz 806-870 MHz Handset Part Number Telephone Style, Complete Handset GMUN1006_ Antennas Part Number Rooftop Mount Antenna for 380 - 400 MHz FAE 5521_...
Page 29
MODEL INFORMATION & ACCESSORIES MTM700 Mobile Radio / Detailed Service Manual 2 - 5 MTM700 ACCESSORIES 380-430 MHz 806-870 MHz UK Linecord (3002120F02) packed NTN7375AR Argentina Linecord NTN9246_ Power Cables (to mobile radio) Part Number 12V Power Cable to Batt., 3m with Fuse (10A) GKN6270_ 12V Power Cable to Batt., 6m with Fuse (10A)
Page 30
2 - 6 MTM700 Mobile Radio / Detailed Service Manual MODEL INFORMATION & ACCESSORIES *) Compatibility of Active Data Cable GMKN1022 Compatible Category Model / Part No. Description Yes / No Radio Model M1 / M47PCN6TZ5AN MTM700 380-430 Dash/Desk UHF / MT 912 with Rev.
Digital Modulation Technique The MTM700 is a 380-430 MHz or 806-870 MHz mobile that can operate in dispatch mode. It uses two digital technologies: π/4 DQPSK and Time Division Multiple Access (TDMA). π/4 DQPSK is a modulation technique that transmits information by altering the phase of the radio frequency (RF) signal.
Page 32
3 - 2 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
THEORY OF OPERATION MTM700 Mobile Radio / Detailed Service Manual 4 - 1 CHAPTER 4 THEORY OF OPERATION Section Introduction This section provides a block diagram overview of the main Digital/RF Board. This is supplemented by the detailed block diagram and detailed circuit description.
Page 34
4 - 2 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 1 CHAPTER 4.1 THEORY OF OPERATION (400 MHz) Block Diagram and Overview The main Digital/RF Block contains the following four sections (see figure below). An overview of these four sections is provided in the following paragraphs: •...
4.1 - 2 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) Receiver Section The receiver section includes the following main components: • Antenna Switch • AGC_0 Attenuator • Front End Pre-selector Filter • Low Noise Amplifier (LNA) •...
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 3 Transmitter Section The transmitter incorporates cartesian feedback circuitry to enhance transmitter linearity to reduce power splatter into adjacent channels. The transmitter circuitry comprises the following components: •...
4.1 - 4 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) Controller Section This section includes the RedCap2, which controls the transmit, receive and synthesize operations of the integrated circuits located in the RF section. Within the RedCap2 are the DSP and the serial interfaces.
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 5 Frequency Generating Section The frequency generating section comprises the following components: • Reference Oscillator - TCXO • Main Synthesizer - consists of the Main Voltage Controlled Oscillator (VCO) and Low Voltage Fractional-N integrated circuit (LVFRACN).
4.1 - 6 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) The receive pre-selector filter performs the following functions: • passes frequencies in the 380 – 430 MHz receive frequency range, and • blocks unwanted spurious frequencies like half IF and image frequencies.
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 7 The analog modulation signal is passed on to the LNODCT where it is up-converted to the transmit- ter operating frequency. The modulated RF output signal from the LNODCT is converted from differ-...
4.1 - 8 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) The reference oscillator –TCXO is a temperature compensated crystal oscillator producing an accu- rate and stable 16.8 MHz master clock, from which all other clocks in the radio are derived. It pro- vides the reference frequency for the following components: •...
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 9 Controller Section The controller section contains the RedCap2 dual core (DSP / RISC) processor and its external memory, the TX and RX audio processing, the serial interfaces and I/O circuitry. The RedCap2 and its external memory is placed on a sub-board in the controller section.
4.1 - 10 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) Detailed Circuit Description Receiver Path, Detailed Circuit Description For the Receive Path Block Diagram see Figure 2. Antenna Switch The signal coming from the antenna is routed to the receiver section via the harmonic filter, which is comprised of L5461, L5462, and C5462 to C5467.
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 11 the image and half IF frequencies. From the output of the second pre-selector filter the received sig- nal is sent to the RF input port of the first mixer.
4.1 - 12 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) Transmitter Path, Detailed Circuit Description For the Transmit Path Block Diagram see Figure 3. ADDAG The Analog to Digital/Digital to Analog IC U5802 (ADDAG) receives the modulation waveform as serial data transmitted by the DSP at a 48 kbps rate to the SSI port (pin 33, STD).
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 13 ferentially on pins 51 and 52 (RFOUTB, RFOUT), where the differential RF signal is converted to a single-ended unbalanced output by means of BALUN L5807. The output signal from the BALUN is applied to the RF Power Amplifier.
4.1 - 14 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) Frequency Generating Section Detailed Circuit Description For the Frequency Generating Section Block Diagram see Figure 4. This section describes the generating circuits that supply all the required frequencies for the required transmitter and receiver functions.
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 15 Transmit Frequency Translation Loop The Transmit Frequency Translation Loop comprises the following components: • transmit Voltage Controlled Oscillator (VCO) and • the ESCORT Near Unity Divider (NUD) Phase Locked Loop IC.
4.1 - 16 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) Controller Section For the Controller Section Block Diagram see Figure 5. This section describes the related circuits as follows: • DC Power Distribution • Microprocessor •...
Page 51
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 17 9V3 Linear Regulator U0301 Regulator U0301 is connected to the 13.2 volts supply voltage via fuse F0300. The output of this regulator is controlled by the ON/OFF circuitry. When any of the signals RTC_ON_SW, ON_OFF_CONTROL_SV, SOFT_TURN_OFF, IGNITION is at high level or EMERGENCY is at low level the regulator is switched on via transistors Q0302, Q0301, Q0303.
Page 52
4.1 - 18 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) 5V_TX Linear Regulator U0304 Regulator U0304 gets its input voltage from the 9.3 volt regulator U0300. The output voltage 5V_TX is fixed to 5 volts and is mainly used in the transmitter section.
4.1 - 20 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) The RedCap2 dual core (DSP / RISC) processor (U0100-1) located on the micro-controller sub- board controls the radio hardware, communicates via various interfaces with external equipment or accessories and performs digital signal processing.
THEORY OF OPERATION (400 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.1 - 21 U0102-1 and U0102-2 perform buffering and level shifting from 3 volts to 5 volts level. The RedCap2 uses its UARTB for the SBEP serial interface.
Page 56
4.1 - 22 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (400 MHz) The Audio system consists of the following components: • RX and TX path multiplexer • RX and TX programmable potentiometer • CODEC • • Audio PA...
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 1 CHAPTER 4.2 THEORY OF OPERATION (800 MHz) Diagram and Overview The main Digital/RF Block contains the following four sections (see figure below). An overview of these four sections is provided in the following paragraphs: •...
4.2 - 2 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) Receiver Section The receiver section includes the following main components: • Antenna Switch • Limiter • Front Pre-selector Filter • Low Noise Amplifier (LNA) •...
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 3 Transmitter Section The transmitter incorporates cartesian feedback circuitry to enhance transmitter linearity to reduce power splatter into adjacent channels. The transmitter circuitry comprises the following components: •...
4.2 - 4 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) Controller Section This section includes the RedCap2, which controls the transmit, receive and synthesize operations of the integrated circuits located in the RF section. Within the RedCap2 are the DSP and the serial interfaces.
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 5 Frequency Generating Section The frequency generating section comprises the following components: • Reference Oscillator - TCXO • Main Synthesizer - consists of the Main Voltage Controlled Oscillator (VCO) and Low Voltage Fractional-N integrated circuit (LVFRACN).
4.2 - 6 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) The receive pre-selector filter performs the following functions: • passes frequencies in the 851 – 870 MHz receive frequency range, and • blocks unwanted spurious frequencies like half IF and image frequencies The signal is mixed with the low side injection local oscillator signal to create the first IF at 73.35...
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 7 The analog modulation signal is passed on to the LNODCT where it is up-converted to the transmit- ter operating frequency. The modulated RF output signal from the LNODCT is converted from differ-...
4.2 - 8 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) The reference oscillator –TCXO is a temperature compensated crystal oscillator producing an accu- rate and stable 16.8 MHz master clock, from which all other clocks in the radio are derived. It pro- vides the reference frequency for the following components: •...
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 9 Controller Section The controller section contains the RedCap2 dual core (DSP / RISC) processor and its external memory, the TX and RX audio processing, the serial interfaces and I/O circuitry. The RedCap2 and its external memory is placed on a sub-board in the controller section.
4.2 - 10 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) Detailed Circuit Description Receiver Path, Detailed Circuit Description For the Receive Path Block Diagram see Figure 2. Antenna Switch The signal coming from the antenna is routed to the receiver section via the harmonic filter, which is comprised of L5461, L5462, and C5462 to C5467.
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 11 and prevent clipping of high level signals. This circuit avoids the use of fixed switchable attenuators typically used in Automatic Gain Control (AGC) circuits. IF Digitizing Subsystem The IF Digitizing Subsystem is comprised of U5101.
4.2 - 12 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) Transmitter Path, Detailed Circuit Description For the Transmit Path Block Diagram see figure 3. ADDAG The Analog to Digital/Digital to Analog IC U5802 (ADDAG) receives the modulation waveform as serial data transmitted by the DSP at a 48 kbps rate to the SSI port (pin 33, STD).
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 13 ferentially on pins 51 and 52 (RFOUTB, RFOUT), where the differential RF signal is converted to a single-ended unbalanced output by means of BALUN L5807. The output signal from the BALUN is applied to the RF Power Amplifier.
4.2 - 14 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) Frequency Generating Section Detailed Circuit Description For the Frequency Generating Section Block Diagram See Figure 4. This section describes the generating circuits that supply all the required frequencies for the required transmitter and receiver functions.
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 15 Transmit Frequency Translation Loop The Transmit Frequency Translation Loop comprises the following components: • transmit Voltage Controlled Oscillator (VCO) and • the ESCORT Near Unity Divider (NUD) Phase Locked Loop IC.
4.2 - 16 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) Controller Section For the Controller Section Block Diagram see Figure 5. This section describes the related circuits as follows: • DC Power Distribution • Microprocessor •...
Page 73
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 17 ON_OFF_CONTROL_SV, SOFT_TURN_OFF, IGNITION is at high level or EMERGENCY is at low level the regulator is switched on via transistors Q0302, Q0301, Q0303. In addition, regulators U0300 and U0302 are also switched on by the same signal.
Page 74
4.2 - 18 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) U5321. Diode D0303 compensates the base to emitter voltage drop of Q0305. The voltage is used for the optional UART connected to J0570. 3V_DIG Linear Regulator U0305 Regulator U0305 gets its input voltage from the 5 volt regulator U0303.
4.2 - 20 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) The RedCap2 dual core (DSP / RISC) processor (U0100-1) located on the micro-controller sub- board controls the radio hardware, communicates via various interfaces with external equipment or accessories and performs digital signal processing.
THEORY OF OPERATION (800 MHz) MTM700 Mobile Radio / Detailed Service Manual 4.2 - 21 U0102-1 and U0102-2 perform buffering and level shifting from 3 volts to 5 volts level. The RedCap2 uses its UARTB for the SBEP serial interface.
Page 78
4.2 - 22 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (800 MHz) The Audio system consists of the following components: • RX and TX path multiplexer • RX and TX programmable potentiometer • CODEC • • Audio PA...
THEORY OF OPERATION (CONTROL HEADS) MTM700 Mobile Radio / Detailed Service Manual 4.3 - 1 CHAPTER 4.3 THEORY OF OPERATION (CONTROL HEADS) This chapter contains the descriptions of the: • Standard Control Head • Expansion Head • Remote Mount Head •...
U0861 via line 5 SOURCE and transistor Q0866 and the controlhead’s microprocessor starts execu- tion. Microprocessor Circuit The controlheadcontrolhead uses the Motorola 68HC11K4 microprocessor (uP) (U0871) to control the LED’s and the LCD and to communicate with the host radio. RAM and ROM are contained within the microprocessor itself.
THEORY OF OPERATION (CONTROL HEADS) MTM700 Mobile Radio / Detailed Service Manual 4.3 - 3 SBEP Serial Interface The host radio (master) communicates to the controlhead µP (slave) through its SBEP bus. This bus uses only line BUS+ for data transfer. The line is bi-directional, meaning that either the radio or the controlhead µP can drive the line.
4.3 - 4 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (CONTROL HEADS) The µP can control the LED’s by changing the dc level at the base of Q0943. If the base of Q0943 is at ground level, Q0943 is switched off and no current flows through Q0941 and the LED’s. If the base voltage of Q0943 rises a current flows through Q0943 and in turn through Q0941 causing the LED’s to turn on and a rising voltage drop across R0955, R0957.
THEORY OF OPERATION (CONTROL HEADS) MTM700 Mobile Radio / Detailed Service Manual 4.3 - 5 Line PTT IRDEC (J0811-6) is used to key up the radio’s transmitter. While the PTT button on a con- nected microphone is released, line PTT IRDEC is pulled to +5 volts level by R0880. Transistor Q0871 is switched on and causes a low at µP port PA2.
EIA/TIA-232 and V.28/V.24 communications interface. This interface can be fully accessed through the 9-pin D-connector. The circuit comprising ICs U1015, U1016 and U1010 interfaces the MTM700 SPIB bus to an asyn- chronous serial-data communication port RS232 that is the 4-wire RS232 interface (pins 2, 3, 4, 5).
THEORY OF OPERATION (CONTROL HEADS) MTM700 Mobile Radio / Detailed Service Manual 4.3 - 7 radio via the 12-pin flex (J1001). The SBEP interface is always available on the Telco connector. The Expansion PTT signal on the Telco connector is routed though the Expansion Board via Q1083.
4.3 - 8 MTM700 Mobile Radio / Detailed Service Manual THEORY OF OPERATION (CONTROL HEADS) Motorcycle Control Head The Control Head forms the interface between the radio and the user. It includes an LCD display, an ON/OFF switch/volume control, and keypad and control keys.
THEORY OF OPERATION (CONTROL HEADS) MTM700 Mobile Radio / Detailed Service Manual 4.3 - 9 Controller LCD controller U2 contains the default character set. The controller is expanded by use of an LCD driver, U3. The LCD controller is connected the µC via data bus PA0-PA7, while the control and read/write (R/W) lines are connected via PB5 and PB7 respectively.
Page 88
4.3 - 10 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
PROGRAMMING THE RADIO MTM700 Mobile Radio / Detailed Service Manual 5 - 1 CHAPTER 5 PROGRAMMING THE RADIO Programming of Software Features and Flashing of Radio Firmware SETING UP THE HARDWARE The programming cable interfaces between the radio and an IBM PC (or compatible computer) running the TETRA CPS.
Page 90
5 - 2 PROGRAMMING THE RADIO MTM700 Mobile Radio / Detailed Service Manual To Computer Serial Port MTM700 e Hardware To MTM700 Accessory Connector on the rear side Programming Cable GMKN4067_ Figure 1 PROGRAMMING WITH STANDARD CONTROL HEAD To Computer Serial Port...
PROGRAMMING THE RADIO MTM700 Mobile Radio / Detailed Service Manual 5 - 3 To Computer Serial Port MTM700 e Hardware Connect Pin 6 to Pin 14 To MTM700 to switch on the radio and 9 Pin Connector to enter programming mode.
5 - 4 PROGRAMMING THE RADIO MTM700 Mobile Radio / Detailed Service Manual After a successful writing, the message “The operation was successful” appears on the computer screen. 5. Press the OK button. Frequency Programming Carry out the following steps if you need to add or change the radio frequencies.
PROGRAMMING THE RADIO MTM700 Mobile Radio / Detailed Service Manual 5 - 5 Hereafter, there is no need for quick sequence of pressing the radio keys. 8. Press the “Down” navigation key to scoll to “Cell Lists” 9. Press the “Ok” key.
Page 94
5 - 6 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
6 - 1 CHAPTER 6 TEST SETUP & TESTING Any level 3 repairs can deeply affect the performance of the MTM700 radio and may cause a new tuning procedure. This tuning procedure can only be applied by certain authorized Motorola W A R N I N G depots where the appropriate TEST&TUNE EQUIPMENT is available.
6 - 2 MTM700 Mobile Radio / Detailed Service Manual TEST SETUP & TESTING Test Equipment The table below lists the special test equipment required for servicing TETRA mobile radios. Table 1 Test Equipment Name Part Number Digital Multimeter R1072_...
TEST SETUP & TESTING MTM700 Mobile Radio / Detailed Service Manual 6 - 3 Test Check List The following table summarises the required test setups. (Values for 380-430 MHz radio in brackets [ ]) Table 2 Test setup Test Name...
6 - 4 MTM700 Mobile Radio / Detailed Service Manual TEST SETUP & TESTING Table 2 Test setup Test Name Test Setup Radio Setup Test Conditions Limits Frequency Error -/+ 80Hz Vector Error Max 10% RMS, Max 30% Peak, Max 5% Residual...
TEST SETUP & TESTING MTM700 Mobile Radio / Detailed Service Manual 6 - 5 Configuration of the IFR 2968 System Setup The setup depends on the firmware version of the IFR 2968, the firmware version of the radio and the customer programming of the radio.
Page 100
6 - 6 MTM700 Mobile Radio / Detailed Service Manual TEST SETUP & TESTING 9. Press the “Control Channel” soft key and enter “2040” [“840”] using the data keys fol- lowed by the “Control Channel” soft key. 10. Press the “Traffic Channel” soft key and enter “2040” [“840”] using the data keys.
Page 101
TEST SETUP & TESTING MTM700 Mobile Radio / Detailed Service Manual 6 - 7 NEIGHBOUR CELL BROADCAST: NOT REQUIRED BROADCAST INTERVAL: NEIGHBOUR CELL CHANNEL: 0000 NEIGHBOUR CELL LOCATION AREA: 00001 NEIGHBOUR CELL IDENTIFIER: SLOW RE-SELECT THRESHOLD: 10dB SLOW RE-SELECT HYSTERESIS:...
6 - 8 MTM700 Mobile Radio / Detailed Service Manual TEST SETUP & TESTING Configuration of the IFR 2968 Manual Test Screen The setup depends on the firmware version of the IFR 2968, the firmware version of the radio and the customer programming of the radio. The following procedure is only an example.
TEST SETUP & TESTING MTM700 Mobile Radio / Detailed Service Manual 6 - 9 RF Tests Receiver Tests Simulate Base Station (registration) 1. Turn the radio ON 2. Check that registration and “ITSI: ---/----/01490199” (as example only) is displayed on the IFR “Manual Test”...
6 - 10 MTM700 Mobile Radio / Detailed Service Manual TEST SETUP & TESTING Actual RSSI measured =IFR RF Gen Level - Cable insertion loss +/- other stray losses. Range of Actual RSSI measured = -90dBm - XdB (cable) +/- 1 dB.
TEST SETUP & TESTING MTM700 Mobile Radio / Detailed Service Manual 6 - 11 Call Processing Test Before you start these tests, make sure that radio and test equipment are configured the same as given in the Transmitter Test. Talk Back 1.
Page 106
6 - 12 MTM700 Mobile Radio / Detailed Service Manual TEST SETUP & TESTING - Frequency Error: -/+ 80Hz - Vector Error: Max 10% RMS, Max 30% Peak. Max 5% Residual. 4. Press the “Talk Back” soft key. 5. Speak into the radio microphone and hear your speech (after a short delay) from the radio loudspeaker.
TEST SETUP & TESTING MTM700 Mobile Radio / Detailed Service Manual 6 - 13 Service Flow Chart (Board Level) Start NOTE: Before replacing any kits, check the If the radio does not have a control head flexes to the control head or expansion attached you need to connect a control head.
MTM700 Mobile Radio / Detailed Service Manual TEST SETUP & TESTING Self Check (Error & Fail Codes) Table 1 lists the possible self check error (non fatal) codes for MTM700 Mobile Radios. No corrective action is required. Table 3 Self Check Error (Non-Fatal) Codes...
Page 109
TEST SETUP & TESTING MTM700 Mobile Radio / Detailed Service Manual 6 - 15 Table 4 Self Check Error (Non-Fatal) Codes Message Cause Fail00811 CP-Corrupted codeplug Fail00812 CP-Radio operation system error Fail00813 CP-Lower layer error Fail00814 CP-Too many arguments Fail00815...
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 1 CHAPTER 7 MAINTENANCE Introduction This chapter provides details about the following: • Preventive maintenance (inspection and cleaning). • Safe handling of CMOS and LDMOS devices. • Repair procedures and techniques.
7 - 2 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE Cleaning External Plastic Surfaces Apply the 0.5% detergent-water solution sparingly with a stiff, non-metallic, short-bristled brush to work all loose dirt away from the radio. Use a soft, absorbent, lintless cloth or tissue to remove the solution and dry the radio.
• Ground the working surface of the service bench to protect the CMOS device. We recommend using the Motorola Static Protection Assembly (part number 0180386A82), which includes a wrist strap, two ground cords, a table mat, and a floor mat.
When damaged parts are replaced, identical parts should be used. If the identical replacement part is not locally available, check the parts list for the proper Motorola part number and order the part from the nearest Motorola Communications parts center listed in the “SUPPORT CENTRES”...
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 5 Radio Disassembly and Reassembly - Detailed The procedure to remove and replace a Control Head, Top Cover or Transceiver Board is similar for all models of radio. A typical procedure is therefore shown followed by specific disassembly...
7 - 6 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE CH_D__FLEX__M_CHAS Figure 2 Flexible Connection Removal Remove the flexible connection from the socket on the control head board. Top Cover Removal Insert the dismantling tool in the middle of the radio assembly side groove as shown in Figure 6 - 3.
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 7 Transceiver Board Removal Remove six screws from the diecast cover using the T20 TORX™ driver as shown in Figure 6 - 4. Lift the cover from the chassis. Screws (6)
7 - 8 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE Reassembly the Radio Chassis And Transceiver Board Inspect the transceiver board and ONLY if the surface of the thermal pads show signs of dam- age, remove the thermal pads and apply thermal grease to the heatsink area on the chassis and heat dissipating devices.
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 9 Standard Control Head - Disassembly To dismount the control head housing from the back housing, insert the dismantling tool in the groove between the two housings as shown in the following Figure.
7 - 10 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE Standard Control Head - Reassembly Fit the rubber keypad onto the board ensuring that the on/off control and on the board locate correctly with the cut-outs in the keypad.
To Disassemble the Radio from the Control Head Remove the Control Head from the Transceiver by inserting the dismantling tool (Motorola part number 6686119B01) in the recess between the Control Head and the Transceiver. Split the Controlhead into Front and Back housings by inserting the dismantling tool in the recess between them.
7 - 12 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE Remote Mount Head - Reassembly To Reassemble the Remote Front Housing: Connect the flex from the Remote Front Housing to the top small connector in the Transceiver. NOTE: For correct orientation of the flex in the Transceiver, the “plastic” tab should be up, contacts facing down.
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 13 Expansion Head - Disassembly CAUTION: The radio must be disconnected from the power supply before commencing any disassembly. The Radio Installation Manual should be referred to for more detailed informa- tion warnings and safety.
7 - 14 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE To Disassemble the Connector Board from Expansion Head Housing Remove the silicon rubber frame Remove the four screws from the connector board. Remove all the protection caps on the front of the expansion head housing.
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 15 Motorcycle Control Head - Disassembly For disassembly of the Motorcycle version control head, use the following tools: Parker’s screwdriver, a pair of tweezers. Unscrew the wing screws of the control head trunnion and remove the control head from the trunnion.
The following table lists the service aids recommended for working on the radio. While all of these items are available from Motorola, most are standard workshop equipment items, and any equivalent item capable of the same performance may be substituted for the item listed.
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 17 EXPLODED VIEWS & PARTS LISTS NOTE: For optimum performance, all replacement parts, diodes, transistors and integrated circuits must be ordered by Motorola part numbers. Transceiver - Exploded View and Parts List...
Page 128
7 - 18 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE Table 17 Transceiver Parts List Item No. Description Part Number Connector 20 Pos. 1586184B01 Connector Assembly 2886122B02 Connector Housing 16Pos. 1580922V01 Gasket Accessory Connector 3202606Y02 Gasket Cover 3286095B01 Cover...
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 19 Standard Control Head - Exploded View and Parts List ZWG0130201-O Figure 12 Standard Control Head - Exploded View Table 18 Standard Control Head - Parts List Item No Description...
7 - 20 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE Expansion Head - Exploded View and Parts List Figure 13 Expansion Head - Exploded View Table 19 Expansion Head - Parts List Item No Description Part No Expansion Head Housing...
MAINTENANCE MTM700 Mobile Radio / Detailed Service Manual 7 - 21 Remote Mount Head - Exploded View and Parts List Figure 14 Remote Mount Head - Exploded View Table 20 Remote Mount Head - Parts List Item No Description Part No...
7 - 22 MTM700 Mobile Radio / Detailed Service Manual MAINTENANCE Motorcycle Control Head - Exploded View and Parts List Figure 15 Motorcycle Control Head - Exploded View Table 21 Motorcycle Control Head - Parts List Item No. Description Part No.
8 - 1 CHAPTER 8 SCHEMATICS, PCBS AND PARTS LISTS Any level 3 repairs can deeply affect the performance of the MTM700 radio and may cause a new tuning procedure. This tuning procedure can only be applied by certain authorized Motorola W A R N I N G depots where the appropriate TEST&TUNE EQUIPMENT is available.
Page 134
8 - 2 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.1 - 1 CHAPTER 8.1.1 Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS SCHEMATICS and PCBS...
Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.1 - 19 SIM_CARD SIM_BUS(5:1) BGA1 SIM_POWER BGA2 SIM_RESET BGA3 SIM_DATA BGA115 SENSE BGA4 SIM_CLOCK DSP_STD goes to CODEC/UCM/DGAN_Module STD Send Transmit I/Q Data to ADDAG...
Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.1 - 21 PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value RF Parts on the Mainboard C5052...
Page 156
8.1.1 - 22 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5336 2113741F49 10nF 50V...
Page 157
Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.1 - 23 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5830 2113740L01 2.0PF+0.1PF D5013...
Page 158
8.1.1 - 24 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Q5681 4880214G02 SLCN NPN M4G02...
Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.1 - 25 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value R5634 0662057A01 10 1/16W 5%...
Page 160
8.1.1 - 26 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C0317 2113740F67 470pF 5% 50V NP0...
Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.1 - 27 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Symbol R0170 0662057A73 10k 1/16W 5%...
Page 162
8.1.1 - 28 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A01_O): SCHEMATICS, PCBs and PARTS LISTS THIS PAGE INTENTIONALLY LEFT BLANK...
Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.2 - 1 CHAPTER 8.1.2 Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS SCHEMATICS and PCBS...
Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.2 - 19 SIM_CARD SIM_BUS(5:1) BGA1 SIM_POWER BGA2 NOTE: The register used to receive data (from the DSP) in the ADDAG is called...
Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.2 - 21 PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value RF Parts on the Mainboard C5052...
Page 184
8.1.2 - 22 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5343 2311049A57 TANT CP 10uF 10%...
Page 185
Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.2 - 23 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5833 2113743E20 100nF 16V...
Page 186
8.1.2 - 24 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Q5552 4802245J54 UMG5N DIGITAL...
Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.2 - 25 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Symbol R5605 0662057A31 180 1/16W 5%...
Page 188
8.1.2 - 26 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS Reference Reference Reference Reference Motorola PN Value Motorola PN Value Motorola PN Value Motorola PN Value Symbol Symbol Symbol Symbol...
Page 189
Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.1.2 - 27 Reference Reference Reference Reference Motorola PN Value Motorola PN Value Motorola PN Value Motorola PN Value Symbol Symbol Symbol Symbol...
8.1.2 - 28 MTM700 Mobile Radio / Detailed Service Manual Transceiver 400MHz (PCB No. 8466519A02_A): SCHEMATICS, PCBs and PARTS LISTS Parts on the HDI Controller Board Reference Reference Motorola PN Value Motorola PN Value Symbol Reference Symbol Motorola PN Value...
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 1 CHAPTER 8.2.1 Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS SCHEMATICS and PCBS...
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 19 SIM_CARD SIM_BUS(5:1) BGA1 SIM_POWER BGA2 SIM_RESET BGA3 SIM_DATA BGA115 SENSE BGA4 SIM_CLOCK BGA5 DSP_STD goes to CODEC/UCM/DGAN_Module STD Send Transmit I/Q Data to ADDAG...
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 21 Parts List Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Parts on the Mainboard C0138 2113740F67...
Page 212
8.2.1 - 22 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C0416 2113740F57 Chip Capacitor REEL CL1...
Page 213
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 23 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5130 2113743E20 Chip Capacitor. 10 UF 10%...
Page 214
8.2.1 - 24 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5352 2113743L17 Chip Capacitor 1000 PF...
Page 215
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 25 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5633 2113743N46 Chip Capacitor 68.0 PF 5%...
Page 216
8.2.1 - 26 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5856 2113743E10 Chip Capacitor .033 UF 10%...
Page 217
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 27 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value L5806 2462587V38 CHIP IND 220 NH 5% 0805...
Page 218
8.2.1 - 28 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value R0302 0662057A73 Chip Resistor 10K Ohms 5%...
Page 219
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 29 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value R5322 0662057A25 Chip Resistor 100 Ohms 5%...
Transceiver 800MHz (PCB No. 8486079Z01_O): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.1 - 30 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Shields: U5103 5102463J58 3.3V REGULATOR IN...
Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.2 - 1 CHAPTER 8.2.2 Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS SCHEMATICS and PCBS...
Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.2 - 19 SIM_CARD SIM_BUS(5:1) BGA1 SIM_POWER BGA2 NOTE: The register used to receive data (from the DSP) in the ADDAG is called...
8.2.2 - 20 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS Bypass Caps for REDCAP V3_2.775V TP 0111 E0101 C0107 C0108 TP 0102 180pF C0109 0.1uF PWM2_1.8V PWM2_1.8V_FLTR TP 0110 C0129...
Page 241
Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.2 - 21 Parts List Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Parts on the Mainboard C5040 2113743N15 3.6 PF +-.25PF...
Page 242
8.2.2 - 22 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5340 2113743N38 33.0 PF 5%...
Page 243
Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.2 - 23 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C5752 2113743N46 68.0 PF 5%...
Page 244
8.2.2 - 24 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value L5734 2462587V38 IND CHIP 220 NH 5%...
Page 245
Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.2 - 25 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value R5335 0662057N23 100K 5%...
Page 246
8.2.2 - 26 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C0103 2113743E20 100nF 16V...
Page 247
Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.2.2 - 27 Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value C0551 2113740F40 36pF 5% 50V...
8.2.2 - 28 MTM700 Mobile Radio / Detailed Service Manual Transceiver 800MHz (PCB No. 8486079Z02_A): SCHEMATICS, PCBs and PARTS LISTS Parts on the HDI Controller Board Reference Motorola PN Value Reference Motorola PN Value Reference Motorola PN Value Reference Symbol...
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 1 CHAPTER 8.3 CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS Standard Control Head Expansion Head Remote Mount Head Motorcycle Control Head...
Page 250
8.3 - 2 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS D0993 D0992 D0991 S0903 S0904 S0905 D0961 D0963 D0965 D0964 D0966 D0962 R0854 S0908 S0909 S0910 Volume D0967 D0969 D0971 D0968 D0970 D0972...
Page 251
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 3 U0873 CSTCC8.00MG Q0851 TP0871 FLT_A+ R0871 R0873 FLT_A+ BOOT_PWR 4.7K C0871 C0873 1MEG VR0851 3.3uF 0.1uF PTT_IRDEC TP0872 C0851 BOOT_GND D0871 .01uF R0872...
Page 252
8.3 - 4 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS CKD002 CKD002 KEYPAD D 02.0 Klaus-Dieter Demant INT_KP_COL SW0901 SW0906 SW0911 SW0916 SW0921 R0901 R0902 R0903 R0904 R0905 130K SW0902 SW0907 SW0917 SW0922...
Page 253
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 5 CKD002 CKD002 Control Head D WARIS MOBILE PILOT PHASE 02.01.05 Q0941 Q0961 Klaus-Dieter Demant Friday, December 10, 1999 1:42:05 pm FLT_A+ FLT_A+ BL_A_GREEN...
Page 254
8.3 - 6 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS C0810 VR0811 C0813 VR0812 470pF 470pF 5.6V R0811 C0811 C0812 470pF 470pF R0812 ANALOG_INPUT_2 J0811-10 EXT_KP_COL WARIS R0813 GM300 FLT_A+ J0811-1 FLT_A+ R0814...
Page 255
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 7 TP1091 TP1035 TP1065 TP1034 TP1037 R1302 C1015 TP1092 C1302 TP1002 TP1064 C1011 C1013 R1303 TP1076 C1016 R1307 U1302 TP1011 Q1301 C1012 C1301 TP1087...
Page 256
8.3 - 8 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS PIN12->MARKER 10 Pin TELCO TP1005 UART_B SCI_TX J1001-12 SPKR+ SPKR+ SPKR+ SPKR+ J1001-11 J1005-22 SPKR+ SPKR+ SPKR- SPKR- SPKR- SPKR- J1001-10 J1005-8 SPKR-...
Page 257
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 9 TP0153 TP0152 TP0151 TP0155 TP0154 PCB / EXPANSION_HEAD / Connector Board / BOTTOM & TOP SIDE...
Page 258
8.3 - 10 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS EXPANSION_HEAD / Connector Board / Schematic Diagram...
Page 259
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 11 VR0921 VR0923 C0921 C0925 C0929 C0923 C0927 VR0924 VR0922 C0930 C0924 C0922 C0928 C0926 R0916 TP0903 J0921 TP0905 TP0906 R0912 C0902 C0904 Q0904...
Page 260
8.3 - 12 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS TP0902 C0904 C0902 R0902 R0904 10uF 0.1uF 1.2K TP0903 Q0902 R0903 BUS- BUS- 1.2K R0905 R0910 4.7K TP0905 U0901-1 R0915 MC33072 R0916 D0901...
Page 261
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 13 8408184y01 R110 R120 R111 + C32 8408184y01 J2 is not equipped PCB / MOTORCYCLE_CONTROL_HEAD / BOTTOM & TOP SIDE...
Page 262
8.3 - 14 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS DISPLAY SW_B+ VCC_5V LCD_2_LINE 78M05 0.33UF 1000PF 10UF 0.1UF 1000PF LDATA1 LOAD CLKLA VCC_5V CLKSR LC7930N LC7985N Y-GR VCC_5V VCC_5V 0.01UF Y-GR Y-GR...
Page 263
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 15 VCC_5V 100K VCC_5V MC33072 3904 VCC_5V VCC_5V VCC_5V 0.01UF SW_B+ MS_2800 4.7K VCC_5V VCC_5V S-807 4.7K BUSY_OUT BUSY_IN RESET 18 PIN CONN. 3906 2.2K...
Page 264
8.3 - 16 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS Parts List Standard Control Head Circuit Motorola Circuit Motorola Circuit Motorola Description Description Description Part No Part No Part No D0855 4813833C02 DUAL SOT MMBD6100...
Page 265
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 17 Expansion Head / Expansion Board Circuit Motorola Circuit Motorola Circuit Motorola Description Description Description Part No Part No Part No Reference Motorola Value...
Page 266
8.3 - 18 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS Remote Mount Head Reference Motorola Value Reference Motorola Value Reference Motorola Value Symbol Symbol Symbol Reference Motorola Value C1056 2113740F49 82pF 5% 50V...
Page 267
CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS MTM700 Mobile Radio / Detailed Service Manual 8.3 - 19 Motorcycle Control Head Reference Motorola Value Symbol Reference Motorola Value R24-51 0662057A73 Symbol R52-58 0662057A69 6.8K 2113741F49 0.01UF R59-68 0662057A65 4.7K 2113741D32 0.33UF 0662057A61 3.3K...
Page 268
8.3 - 20 MTM700 Mobile Radio / Detailed Service Manual CONTROL HEADS: SCHEMATICS, PCBs and PARTS LISTS THIS PAGE INTENTIONALLY LEFT BLANK...
CPS programme. Test Procedures This section explains the procedures required to troubleshoot a MTM700 radio. Whenever possible the radio should be tested and tuned using the automatic test system PATS before troubleshooting. The PATS result file can provide useful hints to determine the failing circuitry section. Alternatively, the Main Function Test Procedure can be performed to determine where to start troubleshooting.
Page 270
9 - 2 TROUBLESHOOTING MTM700 Mobile Radio / Detailed Service Manual IFR2968 Power Supply N-Type 13.2V 5A RF Connector DC Cable RF-Cable MTM700 Testbox BNC-Type RLN4460 RF Connector To PC RS232 Interface GMCN1019A ZWG0130980-O Figure 1 Troubleshooting Setup J0400 Mobile...
TROUBLESHOOTING MTM700 Portable Radio / Detailed Service Manual 9 - 3 For RF levels, which should be measured with a 50 Ohm RF probe, you can use the following circuit. To Multimeter To 50 Ohm Input 1000pF RF + DC Signal...
Page 272
9 - 4 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
9.1 - 2 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) Main Function Test Chart (Sheet 1) >> Startup Procedure << Start Start Tetra Com software. Connect the radio's accessory connector to the Tetra Com interface. Connect the radio's antenna connector to the RF input on the IFR Set the power supply to 13.2V and 1A current limit.
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 3 Main Function Test Chart (Sheet 2) From Sheet 1 Tetra Com Script for RX Test MODE IDLE Setup IFR to: FREQ RX 405.025 No System, L1TIMER ON...
9.1 - 4 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) Controller Troubleshooting (Sheet 1) Failure: No "Radio HW is READY" message on Tetra Com screen 10 sec after the supply voltage has been applied. Communication with PATS failed.
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 5 Controller Troubleshooting (Sheet 2) From Sheet 1 Before replacing U5331 check components between collector Q0100 and U5331 pin 19, check components between Y5362 and Measure the 16.8MHz U5331 pin 23.
9.1 - 6 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) DC Supply Troubleshooting Failure: No 9.3V DC supply. No Digital DC supply. Start Short accessory connector pins 10 and 9 to switch on the radio. 0V DC at U0301 pin 2 13.2V DC...
Page 279
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 7 GPIO & RS232 Troubleshooting Failure: PATS parameters HW_CHECK_UART, HW_CHECK_GPIO failed Start Tetra Com Script for TX FGU Test Connect the radio's accessory connector to the Tetra Com interface.
Page 280
9.1 - 8 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) Receiver Audio Troubleshooting Failure: No audio or low audio level at speaker output or handset audio output. High distortion at speaker output or handset audio output. PATS parameters AUD_LBACK_GAIN or AUD_LBACK_DIST failed.
Page 281
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 9 Transmitter Audio Troubleshooting Failure: No audio, low audio level or distortion > 2% at speaker output during transmitter audio test. PATS parameters AUD_LBACK_GAIN or AUD_LBACK_DIST failed Start If receiver audio has not been checked, go to Receiver Audio Chart first.
9.1 - 10 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) Warping Failure Troubleshooting Failure: PATS parameters WARP_RANGE, WARP_RES, FREQ_ERR or WARP_SP failed Start Tetra Com Script for TX FGU Test Connect the radio's accessory connector to the Tetra Com interface.
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 11 RF Power Amplifier Troubleshooting Failure: No or low RF output power. Too high RF output power. PATS parameters ADJ_PWR1-5, ATT_SP1-5, DC_CUR1-5, TX_PWR_F1-5 failed. Start Connect the radio's accessory connector to the Tetra Com Tetra Com Script for TX Power Test interface.
Page 284
9.1 - 12 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) PA Bias Failure Troubleshooting Failure: PATS parameters PA_BIAS, BIAS1-3_CUR, BIAS_1-3_SP failed Start Tetra Com Script for PA Bias Test TEST_ENTER DELAY 10 Check for "Radio HW is READY"...
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 13 LNODCT Troubleshooting Failure: No or low LNODCT output signal level. Start Tetra Com Script for TX Power Test TEST_ENTER Connect the radio's accessory connector to the DELAY 10 Tetra Com interface.
Page 286
9.1 - 14 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) Receiver Troubleshooting (Sheet 1) Failure: Bit Error Rate @ -114dBm >3.5% RSSI error >+/- 5dB PATS parameter GAIN_OFF_L, GAIN_OFF_H and AGC_SLOPE failed. Start Connect the radio's accessory connector to the Tetra Com interface.
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 15 Receiver Troubleshooting (Sheet 2) level at Q5201 Collector Check transistor about -10dBm and stage Q5201 DC about 3.2V level at Q5101 Collector Check transistor about -2dBm and stage Q5101 DC about 4.4V...
9.1 - 16 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) Front-End Tuning Troubleshooting Failure: PATS parameters FE_FILTER, FE_DAC, FE_OFFSET failed. Start Tetra Com Script for RX Test Connect the radio's accessory connector to the Tetra Com interface.
Page 289
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 17 Tx Frequency Generation Troubleshooting Failure: No or low TX LO signal level. TX frequency error greater than 2 kHz or unstable after frequency tuning. Start Tetra Com Script for TX FGU Test Connect the radio's accessory connector to the Tetra Com interface.
Page 290
9.1 - 18 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (400MHz) Main VCO Troubleshooting Failure: VCO signal level at TP5702 < -5dBm Start Connect the radio's accessory connector to the Tetra Com interface. Connect the radio's antenna connector to the high power RF output on the IFR.
TROUBLESHOOTING CHARTS (400MHz) MTM700 Mobile Radio / Detailed Service Manual 9.1 - 19 Main Synthesizer Troubleshooting Failure: RX injection frequency error greater than 2 kHz or unstable frequency. Main VCO frequency error at TP5702 greater than 2 kHz or unstable frequency after frequency tuning.
Page 292
9.1 - 20 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
9.2 - 2 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (800MHz) Main Function Test Chart (Sheet 1) >> Startup Procedure << Start Start Tetra Com software. Connect the radio's accessory connector to the Tetra Com interface. Connect the radio's antenna connector to the RF input on the IFR Set the power supply to 13.2V and 1A current limit.
Page 295
TROUBLESHOOTING CHARTS (800MHz) MTM700 Mobile Radio / Detailed Service Manual 9.2 - 3 Main Function Test Chart (Sheet 2) From Sheet 1 Tetra Com Script for RX Test MODE IDLE Setup IFR to: FREQ RX 860.0125 No System, L1TIMER ON...
9.2 - 4 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (800MHz) Controller Troubleshooting (Sheet 1) Failure: No "Radio HW is READY" message on Tetra Com screen 10 sec after the supply voltage has been applied. Communication with PATS failed.
Page 297
TROUBLESHOOTING CHARTS (800MHz) MTM700 Mobile Radio / Detailed Service Manual 9.2 - 5 Controller Troubleshooting (Sheet 2) From Sheet 1 Before replacing U5331 check components between collector Q0100 and U5331 pin 19, check components between Y5362 and Measure the 16.8MHz U5331 pin 23.
Page 298
9.2 - 6 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (800MHz) DC Supply Troubleshooting Failure: No 9.3V DC supply. No Digital DC supply. Start Short accessory connector pins 10 and 9 to switch on the radio. 0V DC at U0301 pin 2 13.2V DC...
Page 299
TROUBLESHOOTING CHARTS (800MHz) MTM700 Mobile Radio / Detailed Service Manual 9.2 - 7 GPIO & RS232 Troubleshooting Failure: PATS parameters HW_CHECK_UART, HW_CHECK_GPIO failed Start Tetra Com Script for TX FGU Test Connect the radio's accessory connector to the Tetra Com interface.
Page 300
9.2 - 8 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (800MHz) Receiver Audio Troubleshooting Failure: No audio or low audio level at speaker output or handset audio output. High distortion at speaker output or handset audio output. PATS parameters AUD_LBACK_GAIN or AUD_LBACK_DIST failed.
Page 301
TROUBLESHOOTING CHARTS (800MHz) MTM700 Mobile Radio / Detailed Service Manual 9.2 - 9 Transmitter Audio Troubleshooting Failure: No audio, low audio level or distortion > 2% at speaker output during transmitter audio test. PATS parameters AUD_LBACK_GAIN or AUD_LBACK_DIST failed. Start If receiver audio has not been checked, go to Receiver Audio Chart first.
9.2 - 10 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (800MHz) Warping Failure Troubleshooting Failure: Tetra Com Script for Tx FGU Test: PATS parameters WARP_RANGE, WARP_RES, FREQ_ERR or WARP_SP failed. TEST_ENTER DELAY 10 Check for "Radio HW is READY"...
Page 303
TROUBLESHOOTING CHARTS (800MHz) MTM700 Mobile Radio / Detailed Service Manual 9.2 - 11 Low Tx Power Troubleshooting Failure: No or low RF output power. Too high RF output power. Tetra Com Script for Tx Power Test: PATS parameters ADJ_PWR1-5, ATT_SP1-5, DC_CUR1-5, TX_PWR_F1-5 failed.
9.2 - 12 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (800MHz) PA Bias Failure Troubleshooting Tetra Com Script for PA Bias Test: TEST_ENTER Failure: DELAY 10 PATS parameters PA_BIAS, BIAS1-3_CUR, BIAS1-3_SP failed. Check for "Radio HW is READY"...
TROUBLESHOOTING CHARTS (800MHz) MTM700 Mobile Radio / Detailed Service Manual 9.2 - 13 LNODCT Troubleshooting Tetra Com Script fo Tx Power Test : Failure: No or low LNODCT output signal level. TEST_ENTER DELAY 10 Check for "Radio HW is READY"...
9.2 - 16 MTM700 Mobile Radio / Detailed Service Manual TROUBLESHOOTING CHARTS (800MHz) Tx Frequency Generation Troubleshooting Tetra Com Script for TX FGU Test: TEST_ENTER DELAY 10 Check for "Radio HW is READY" MODE IDLE INTR DIS FREQ TX 869.925...
TROUBLESHOOTING CHARTS (800MHz) MTM700 Mobile Radio / Detailed Service Manual 9.2 - 17 Synthesizer & VCO Troubleshooting Tetra Com Script for Rx Test: TEST_ENTER DELAY 10 Check for “Radio HW is Ready” MODE IDLE FREQ RF 860.525 Measure the RF level at the pres-...
Page 310
9.2 - 18 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
Transceiver Rear - Pin Function Expansion Connector Accessory Connector Antenna DC Power Supply *Note the location of Pin 1 Figure 2 Rear view of the MTM700 with the Accessory and Expansion Connector Function Description Ground Guide pin Request to Send...
Page 312
A - 2 MTM700 Mobile Radio / Detailed Service Manual CONNECTOR PIN FUNCTIONS Function Description Clear To Send SCI – RX Receive Data SCI – TX Transmit Data Ground Table 16 Transceiver Pin Assignment of the 7 pins Expansion Connector (Optional RS232 Interface)
CONNECTOR PIN FUNCTIONS MTM700 Mobile Radio / Detailed Service Manual A - 3 Transceiver Front - Pin Function 12 Pin Connector ......
Page 314
A - 4 MTM700 Mobile Radio / Detailed Service Manual CONNECTOR PIN FUNCTIONS Function Description Ground MUX_CTRL TBA for future applications. SPIB_CLK Part of the QSPIB MUX_CTRL_1 To detect RS232 or SB9600 Mode (3V SB9600 / 0V RS232) * A+ (via 22Ohms) Continuous battery voltage for sense via 22Ohms.
CONNECTOR PIN FUNCTIONS MTM700 Mobile Radio / Detailed Service Manual A - 5 RS232_RTS Request To Send RS232_DTR Data Terminal Ready RS232_CTS Clear To Send RS232_RX RX-Data RS232_RI Ring Indicator OPTION_DET Option Detect; for future applications Regulated 9V3 Not Connected...
Page 316
A - 6 MTM700 Mobile Radio / Detailed Service Manual CONNECTOR PIN FUNCTIONS Handset_audio Handset audio BUS + Either SBEP or Serial Communication Interface RXD Int_Mic Microphone input Flt_A+ Filtered A+ On_Off_Control_SV Radio On/Off Control shared with Control Head request...
CONNECTOR PIN FUNCTIONS MTM700 Mobile Radio / Detailed Service Manual A - 7 Remote Mount Head - Pin Function Front View Caution: Microphone Connector Figure 5 View of the Remote Mount Connector Function Description FLT_A+ Filtered A+ + 5V regulated / 100mA...
A - 8 MTM700 Mobile Radio / Detailed Service Manual CONNECTOR PIN FUNCTIONS Expansion Head - Pin Function Front View Caution: Microphone Connector 9 8 7 6 5 4 3 2 1 10 25 Pin subD 9 Pin subD Connector...
Page 319
CONNECTOR PIN FUNCTIONS MTM700 Mobile Radio / Detailed Service Manual A - 9 Data Set Ready Input Request to Send Output Clear to Send Input Ring Indicator Input Table 24 Pin Assignment of 9 Pin subD Connector of the Expansion Head...
A - 10 MTM700 Mobile Radio / Detailed Service Manual CONNECTOR PIN FUNCTIONS Motorcycle Control Head - Pin Function Figure 7 Front View of the Motorcycle Control Head to Ground Figure 8 Rear View of the Motorcycle Control Head 11 12 13 14 15 16 17...
Page 321
N.C. Not connected. EMC_KEYLOAD Keyload Used for encryption key loading. RESET SB9600 In/Out This is part of the Motorola Bus to connect external Reset devices. BUS- SB9600 Bus- In/Out This is part of the Motorola Bus to connect external devices.
Page 322
A - 12 MTM700 Mobile Radio / Detailed Service Manual THIS PAGE INTENTIONALLY LEFT BLANK...
Accessory Division (AAD). If no part number is assigned, the part is not normally available from Motorola. If a parts list is not included, this generally means that no user-serviceable parts are avail- able for that kit or assembly.
Accessory Division (AAD). If no part number is assigned, the part is not normally available from Motorola. If a parts list is not included, this generally means that no user-serviceable parts are avail- able for that kit or assembly.
B - 4 MTM700 Mobile Radio / Detailed Service Manual REPLACEMENT PARTS & KITS SERVICE KITS Table 1 Model Information Type No. Sales Model No. Short Description Model MT912 M47PCN6TZ5AN MTM700 380-430 MHz, STD DASH/DESK MT912 M47PCN6TZ6AN MTM700 380-430 MHz, STD REMOTE...
Fuse Identification In case of blown fuses during the installation only replace those with identically value. Never insert different values. Fuse for Power Cable GKN6270/GKN6274: 10A (Motorola Part Number: 65C80283E05) Fuse for Ignition Sense Cable HKN9327: 4A (Motorola Part Number: 65C80283E02)
Leitung reduziert. Daraus kann sich eine Verringerung der Leistungsmerkmale des Gerätes ergeben. Sicherungen Sollte während der Installation die Sicherung durchbrennen, darf sie nur durch eine gleichwertige Sicherung ersetzt werden. Sicherung für DC Kabel GKN6270/GKN6274: 10A (Motorola Bestellnummer: 65C80283E05) Sicherung für Ignition Sense Kabel HKN9327: 4A (Motorola Bestellnummer: 65C80283E02)