GE 350 Communications Manual page 68

IEC60870-5-104 PROTOCOL
Fault Report Mapping
Disabled Enabled
Disabled Enabled
- 0
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
3-32
These 64 Single Points and 32 Measured Values will also be sent as a response to a General
Interrogation.
Integrated Totals (M_IT) will have its own Counter Group 1 and these will be sent as a
response to a General Request Counter.
The FAULT REPORT MAPPING IN DNP/104 setpoint may be set to a value of "Disabled" or
"Enabled". When "Disabled", only the configurable Analog Input points are available
beginning with the configured information object address (IOA) for analog values.When
"Enabled", the Fault Report Values are assigned from IOA to IOA + 32 in the 339 and 350
relays, and from IOA to IOA + 38 in the 345 relay, with the configurable Analog Inputs
following that IOAs.To support existing SCADA hardware not capable of 32-bit data reads,
the upper and lower 16-bit portions of the fault report time and date values have been
assigned to separate points. To read a date or time, it is necessary to read both the upper
and lower 16-bit portions, concatenate these two values to form a 32-bit value, and
interpret the result in the format associated with the point.
350 and 339
Fault Report Date Upper 16
Fault Report Date Lower 16
Fault Report Time Upper 16
Fault Report Time Lower 16
Fault Report Fault Type
Fault Report Ia
Fault Report Ia Angle
Fault Report Ib
Fault Report Ib Angle
Fault Report Ic
Fault Report Ic Angle
Fault Report Ig
Fault Report Ig Angle
Fault Report In
Fault Report In Angle
Fault Report Va
Fault Report Va Angle
Fault Report Vb
Fault Report Vb Angle
Fault Report Vc
Fault Report Vc Angle
Fault Report Vab
Fault Report Vab Angle
Fault Report Vbc
Fault Report Vbc Angle
Fault Report Vca
Fault Report Vca Angle
Fault Report Vn
Fault Report Vn Angle
Fault Report Vaux
Fault Report Vaux Angle
Fault Report Mapping
Disabled Enabled
Disabled Enabled
- 0
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
SR3 SERIES PROTECTIVE RELAY PLATFORM – COMMUNICATIONS GUIDE
CHAPTER 3: ETHERNET INTERFACE
345
Fault Report Date Upper 16
Fault Report Date Lower 16
Fault Report Time Upper 16
Fault Report Time Lower 16
Fault Report Fault Type
Fault Report Ia
Fault Report Ia Angle
Fault Report Ib
Fault Report Ib Angle
Fault Report Ic
Fault Report Ic Angle
Fault Report Ig
Fault Report Ig Angle
Fault Report In
Fault Report In Angle
Fault Report System Frequency
Fault Report Ia 2
Fault Report Ia 2 Angle
Fault Report Ib 2
Fault Report Ib 2 Angle
Fault Report Ic 2
Fault Report Ic 2 Angle
Fault Report Ig 2
Fault Report Ig 2 Angle
Fault Report In 2
Fault Report In 2 Angle
Fault Report Idiff 1 PhA
Fault Report Idiff 1 PhA Angle
Fault Report I Restraint PhA
Fault Report I Restraint PhA Angle
Fault Report Idiff 1 PhB