Water-Source Unit Twinning Kit - Mitsubishi Electric PQRY-P72TLMU-A Manual

9. Optional parts

9-3. Water-source Unit Twinning Kit

The water-source unit twinning kit is needed to PQRY-P-TSLMU/YSLMU to combine the refrigerant flows of the
PQRY-P-TLMU/YLMU units.
CMY-Q100CBK2
Low-pressure pipe twinning kit
27(1-2/16)
ø28.58(ø1-1/8)
(Outside diameter)
ø22.2(ø7/8)
(Outside diameter)
High-pressure twinning pipe
ø19.05(ø3/4)
ø22.2(ø7/8)
80(3-3/16)
CMY-Q200CBK
Low-pressure pipe twinning kit
77(3-1/16)
ø31.75(ø1-1/4)
(Outside diameter)
High-pressure twinning pipe
ø19.05(ø3/4)
ø28.58(ø1-1/8)
80(3-3/16)
Note 1. Reference the attitude angle of the branch pipe below the fig.
The angle of the branch pipe for hign pressure is within
2. Use the attached pipe to braze the port-opening of the distributer.
3. Pipe diameter is indicated by inside diameter.
© 2017 Mitsubishi Electric US, Inc.
315(12-7/16)
45(1-13/16)
ø25.4(ø1)
(Outside diameter)
<Pipe for routing through the front (Accessory)>
ø19.05(ø3/4)
ø19.05(ø3/4)
ø19.05(ø3/4)
135(5-1/4)
<Elbow pipe(Accessory)>
407(16-1/16)
72(2-7/8) ø28.58(ø1-1/8)
<Pipe for routing through the front (Accessory)>
(Outside diameter)
(Outside diameter)
ø28.58(ø1-1/8)
(Outside diameter)
<Deformed pipe(Accessory)>
ø19.05(ø3/4) ø22.2(ø7/8)
(Outside diameter)
62
(2-1/2)
<Pipe for routing through the front (Accessory)>
ø19.05(ø3/4)
66
(2-5/8)
ø25.4(ø1)
Distributer
PQRY-P-T(S)LMU, Y(S)LMU (April 2017 Ver2)
<Elbow pipe(Accessory)>
<Accessory>
ø28.58(ø1-1/8)
ø28.58(ø1-1/8)
50(2)
ø22.2(ø7/8)
ø22.2(ø7/8)
36(1-7/16)
<Pipe for routing through the front (Accessory)>
ø28.58(ø1-1/8) ø34.93(ø1-3/8)
187(7-6/16)
Note 1. Refer to the figure below for the installation
position of the high-pressure twinning pipe.
Inclination tolerance of the
high-pressure twinning pipe is ±15°
relative to the ground.
65
(2-9/16)
2. Pipe diameter is indicated
53
by inside diameter.
(2-1/8)
<Accessory>
ø28.58(ø1-1/8)
ø31.75(ø1-1/4)
ø31.75(ø1-1/4)
ø28.58(ø1-1/8)
50(2) 53(2-1/8)
ø31.75(ø1-1/4)
ø34.93(ø1-3/8)
ø28.58(ø1-1/8)
160(6-5/16)
(Outside diameter)
ø41.28(ø1-5/8)
ø34.93(ø1-3/8)
69
(2-3/4)
Note 1. Refer to the figure below for the installation
position of the high-pressure twinning pipe.
185(7-5/16) Inclination tolerance of the
high-pressure twinning pipe is ±15°
ø19.05(ø3/4)
relative to the ground.
2. Pipe diameter is indicated
by inside diameter.
15 against the horizontal plane.
Fixing screw
Insulation cover
Pipe cover (150mm(5-15/16) Length)
Pipe cover (60mm(2-3/8) Length)
Pipe cover (80mm(3-3/16) Length)
Cable tie
Water stopper
Sealing material (Small)
Sealing material (Large)
High-pressure twinning pipe
On-site pipes
Fixing screw
Insulation cover
Pipe cover (75mm(3) Length)
Pipe cover (360mm(14-3/16) Length)
Pipe cover (70mm(2-13/16) Length)
Pipe cover (130mm(5-1/8) Length)
Pipe cover (100mm(3-15/16) Length)
Pipe cover (160mm(6-5/16) Length)
Cable tie
Water stopper
Sealing material (Small)
Sealing material (Large)
ø28.58(ø1-1/8)
215(8-1/2)
High-pressure twinning pipe
On-site pipes
• • • 1
• • • 1
• • • 2
• • • 1
• • • 2
• • • 2
• • • 1
• • • 1
• • • 1
• • • 1
• • • 1
• • • 1
• • • 1
• • • 1
• • • 1
• • • 1
• • • 1
• • • 2
• • • 1
• • • 1
• • • 1
WR2-111