Page 1 Pictorial index Search by illustration For safety Make sure to read through them and security Fuel cell system Fuel cell vehicle characteristics, precautions, etc. Instrument How to read the gauges and meters, the variety of cluster warning lights and indicators, etc. Operation of Opening and closing the doors and windows, each...
Page 2: Table Of Contents
TABLE OF CONTENTS For your information....... 6 Instrument cluster Reading this manual ....12 How to search......13 Pictorial index ......14 Instrument cluster Warning lights and For safety and security indicators ......98 Gauges and meters ... 102 Multi-information display..107 1-1.
Page 3: Table Of Contents
5-5. Using the driving Driving support systems Dynamic radar cruise control......203 5-1. Before driving LDA (Lane Departure Driving the vehicle..... 158 Alert)........216 Cargo and luggage.... 166 Intuitive parking assist ..223 Vehicle load limits ..... 169 Driving assist systems ..232 Trailer towing.....
Page 4: Table Of Contents
TABLE OF CONTENTS Interior features Maintenance and care 6-1. Using the air conditioning 7-1. Maintenance and care system and defogger Cleaning and protecting Automatic air conditioning the vehicle exterior ..306 system......258 Cleaning and protecting Heated steering wheel/ the vehicle interior ... 310 seat heaters ....
Page 5: Table Of Contents
When trouble arises Vehicle specifications 8-1. Essential information 9-1. Specifications Emergency flashers ..360 Maintenance data (fuel, fluid level, etc.) ..416 If your vehicle has to be stopped in an Tire information....422 emergency ...... 361 9-2. Customization 8-2. Steps to take in an Customizable features..
Page 6: For Your Information
Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehi- cles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 7 ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. High voltage parts and cables on the fuel cell vehicles emit approximately the...
Page 8 ● Usage of data collected through Safety Connect (U.S.mainland only) If your Toyota has Safety Connect and if you have subscribed to those ser- vices, please refer to the Safety Connect Telematics Subscription Service Agreement for information on data collected and its usage.
Page 9 EDR. ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehi- cle) is obtained •...
Page 10 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 12: Reading This Manual
Reading this manual WARNING: Explains something that, if not obeyed, could cause death or serious injury to people. NOTICE: Explains something that, if not obeyed, could cause damage to or a malfunction in the vehicle or its equipment. 1 2 3 Indicates operating or working procedures.
Page 13: How To Search
How to search ■ Searching by name • Alphabetical index ..P. 449 ■ Searching installation position • Pictorial index....P. 14 ■ Searching by symptom or sound • What to do if... (Troubleshooting) ..P. 446 ■ Searching by title • Table of contents .....P. 2...
Page 14: Pictorial Index
Pictorial index Pictorial index ■ Exterior Doors ......... . . P. 120 Locking/unlocking .
Page 15 Pictorial index Windshield wipers ....... . . P. 195 Precautions against winter season ..... P. 253 To prevent freezing (windshield wiper de-icer).
Page 16: Instrument Panel
Pictorial index ■ Instrument panel Power switch ........P. 172 Starting the fuel cell system/changing the modes .
Page 17 Pictorial index Parking brake ........P. 186 Applying/releasing .
Page 18 Pictorial index ■ Switches Automatic high beam switch ......P. 190 O switch ........P. 173 Instrument panel light control switches .
Page 19 Pictorial index Power window switches ......P. 154 Window lock switch....... . P. 154 Outside rear view mirror switches .
Page 20 Pictorial index Odometer/trip meter and trip meter reset button ..P. 104 Audio remote control switches Meter control switches ......P. 108 Vehicle-to-vehicle distance button.
Page 21 Pictorial index P position switch ........P. 173 ECO MODE switch .
Page 22 Pictorial index ■ Interior SRS airbags ........P. 36 Floor mats .
Page 23 Pictorial index Inside rear view mirror ......P. 149 Sun visors ........P. 279 Vanity mirrors.
Page 24 Pictorial index ■ Rear interior Rear seat heater switch......P. 268...
Page 25 For safety and security 1-1. For safe use Before driving...... 26 For safety drive ....28 Seat belts ......30 SRS airbags......36 Front passenger occupant classification system ..49 Safety information for children ......55 Child restraint systems..56 1-2.
Page 26: Each
1-1. For safe use Before driving Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eyelets. Turn the upper knob of each retaining hook (clip) to secure the floor mats in place.
Page 27: Driving
■ Do not use floor mats designed for other models or different model year ● vehicles, even if they are Toyota Genuine floor mats. Only use floor mats designed for the driver’s seat. ● Always install the floor mat securely using the retaining hooks (clips) pro- ●...
Page 28: For Safety Drive
1-1. For safe use For safety drive For safe driving, adjust the seat and mirror to an appropriate position before driving. Correct driving posture Adjust the angle of the seat- back so that you are sitting straight up and so that you do not have to lean forward to steer.
Page 29 1-1. For safe use WARNING Observe the following precautions. Failure to do so may result in death or serious injury. Do not adjust the position of the driver’s seat while driving. ● Doing so could cause the driver to lose control of the vehicle. Do not place a cushion between the driver or passenger and the seatback.
Page 30: Seat Belts
1-1. For safe use Seat belts Make sure that all occupants are wearing their seat belts before driving the vehicle. Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoulder.
Page 31 1-1. For safe use Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a Release button click.
Page 32 ■ Seat belt extender If your seat belts cannot be fastened securely because they are not long enough, personalized seat belt extender is available from your Toyota dealer free of charge.
Page 33 Each seat belt should be used by one person only. Do not use a seat belt ● for more than one person at once, including children. Toyota recommends that children be seated in the rear seat and always ● use a seat belt and/or an appropriate child restraint system.
Page 34 Ensure that the belt and plate are locked and the belt is not twisted. ● If the seat belt does not function correctly, immediately contact your Toyota dealer. Replace the seat assembly, including the belts, if your vehicle has been ●...
Page 35 1-1. For safe use WARNING Using a seat belt extender ■ Do not wear the seat belt extender if you can fasten the seat belt without ● the extender. Do not use the seat belt extender when installing a child restraint system ●...
Page 36: Srs Airbags
1-1. For safe use SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. ◆...
Page 37 1-1. For safe use ◆ SRS side and curtain shield airbags SRS side airbags Can help protect the torso and pelvis of the front seat occupants SRS curtain shield airbags ● Can help protect primarily the head of occupants ● Can help prevent the occupants from being thrown from the vehicle in the event of vehicle rollover...
Page 38 1-1. For safe use SRS airbag system components Curtain shield airbags Front passenger’s seat belt buckle switch Side airbags Front passenger occupant Driver airbag classification system (ECU Side impact sensors (rear) and sensors) Side impact sensors (front) Knee airbag Seat belt pretensioners and Airbag sensor assembly force limiters Passenger seat cushion air-...
Page 39 1-1. For safe use Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above.
Page 40 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are...
Page 41 1-1. For safe use WARNING SRS airbag precautions ■ Do not sit on the edge of the seat or ● lean against the dashboard. Do not allow a child to stand in front of ● the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 42 1-1. For safe use WARNING SRS airbag precautions ■ Do not attach anything to or lean any- ● thing against areas such as the dash- board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and knee airbags deploy.
Page 43 ■ Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. Installation, removal, disassembly and repair of the SRS airbags ●...
Page 44 1-1. For safe use ■ If the SRS airbags deploy (inflate) ● Bruising and slight abrasions may result from contact with a deploying (inflating) SRS airbag. ● A loud noise and white powder will be emitted. ● Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, parts of the front and rear pillars, and roof side rails, may be hot for several minutes.
Page 45 1-1. For safe use ■ SRS airbag deployment conditions (SRS side and curtain shield airbags) ● The SRS side and curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to the impact force produced by an approximately 3300 lb.
Page 46 1-1. For safe use ■ Types of collisions that may not deploy the SRS airbags (SRS front airbags) The SRS front airbags do not generally inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low-speed frontal collision.
Page 47 Pitching end over end ■ When to contact your Toyota dealer In the following cases, the vehicle will require inspection and/or repair. Con- tact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ●...
Page 48 1-1. For safe use ● The front passenger’s seat cushion sur- face is scratched, cracked, or otherwise damaged. ● The surface of the seats with the side airbag is scratched, cracked, or other- wise damaged. ● The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding), containing the curtain shield airbags inside, is scratched, cracked, or other-...
Page 49: Front Passenger Occupant Classification System
1-1. For safe use Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classi- fication system. This system detects the conditions of the front passenger seat and activates or deactivates the devices for the front passenger. SRS warning light Seat belt reminder light “AIR BAG OFF”...
Page 50 1-1. For safe use Conditions and operations in the front passenger occupant clas- sification system ■ Adult “AIR BAG ON” and “AIR BAG OFF” “AIR BAG ON” indicator lights Indicator/ SRS warning light warning light Seat belt reminder light flashing Front passenger airbag Side airbag on the front passenger seat...
Page 51 1-1. For safe use ■ Child restraint system with infant “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights OFF” Indicator/ SRS warning light warning light Seat belt reminder light flashing Front passenger airbag Deactivated Side airbag on the front passenger seat Activated Curtain shield airbag Devices...
Page 52 1-1. For safe use ■ There is a malfunction in the system “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights OFF” Indicator/ warning light SRS warning light Seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seats Activated Curtain shield airbag...
Page 53 1-1. For safe use WARNING Front passenger occupant classification system precautions ■ Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. Wear the seat belt properly. ● Make sure the front passenger’s seat belt plate has not been left inserted ●...
Page 54 SRS warning light may come on to indicate a malfunction of the front passenger occupant classification system. In this case, contact your Toyota dealer immediately. Child restraint systems installed on the rear seat should not contact the ●...
Page 55: Safety Information For Children
1-1. For safe use Safety information for children Observe the following precautions when children are in the vehi- cle. Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt.
Page 56: Child Restraint Systems
1-1. For safe use Child restraint systems Before installing a child restraint system in the vehicle, there are precautions that need to be observed, different types of child restraint systems, as well as installation methods, etc., written in this manual. Use a child restraint system when riding with a small child that can- not properly use a seat belt.
Page 57 Toyota strongly urges the use of a proper child restraint system that con- ● forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 58 1-1. For safe use Child restraint system ■ Types of child restraint system installation methods Confirm with the operation manual enclosed with the child restraint system about the installation of the child restraint system. Installation method Page Seat belt P. 62 attachment Child restraint LATCH P.
Page 59 1-1. For safe use When using a child restraint system on a passenger seat ■ When installing a child restraint system to a passenger seat For the safety of a child, install child restraint systems to a rear seats. When installing child restraint system to a front passenger seat is unavoidable, adjust the passenger seat as follows and install the child restraint system.
Page 60 1-1. For safe use WARNING When installing a child restraint system ■ Observe the following when installing child restraint system to the front pas- senger seat if it is unavoidable. The front passenger SRS airbag inflates with considerable speed and force that if not observed may lead to death or serious injury to the child.
Page 61 1-1. For safe use When using a child restraint system on a rear seat WARNING When installing a child restraint system ■ Observe the following precautions. Failure to do so may result in death or serious injury. Use child restraint system suitable to the age and size of the child and ●...
Page 62 1-1. For safe use Child restraint system fixed with a seat belt A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. ◆ Installing child restraint system using a seat belt (child restraint lock function belt) Install the child restraint system in accordance to the operation...
Page 63 1-1. For safe use While pushing child restraint system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 64 1-1. For safe use Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended. While pushing child restraint system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.
Page 65 1-1. For safe use Place the child restraint system on the seat facing the front of the vehicle.  Booster type  High back type Sit the child in the child restraint system. Fit the seat belt to the child restraint sys- tem according to the manu- facturer’s instructions...
Page 66 1-1. For safe use WARNING When installing a child restraint system ■ Observe the following precautions. Failure to do so may result in death or serious injury. Do not allow children to play with the seat belt. If the seat belt becomes ●...
Page 67 1-1. For safe use Child restraint system fixed with a child restraint LATCH anchors ■ Child restraint LATCH anchors LATCH anchors are provided for each rear seats. (Buttons displaying the location of the anchors are attached to the seats.) ■ Installation with LATCH system Install the child restraint system in accordance to the operation manual enclosed with the child restraint system.
Page 68 1-1. For safe use  Type A Latch the hooks of the lower straps onto LATCH anchors.  Type B Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, follow the child restraint manufacturer’s operation manual regarding the installa- tion, using the top tether strap to latch onto the top tether strap anchor.
Page 69 1-1. For safe use After installing the child restraint system, rock it back and forth to ensure that it is installed securely. Laws and regulations pertaining to anchors ■ The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used.
Page 70 1-1. For safe use ■ Fixing the top tether strap to the anchor bracket Install the child restraint system in accordance to the operation manual enclosed with the child restraint system. Adjust the head restraint to the upmost position. If the head restraint interferes with the child restraint system or top tether strap installation and head...
Page 71 1-1. For safe use WARNING When installing a child restraint system ■ Observe the following precautions. Failure to do so may result in death or serious injury. Firmly attach the top tether strap and make sure that the belt is not twisted. ●...
Page 72: Theft Deterrent System Immobilizer System
1-2. Theft deterrent system Immobilizer system The vehicle’s keys have built-in transponder chips that prevent the fuel cell system from starting if a key has not been previ- ously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehi- cle.
Page 73 1-2. Theft deterrent system System maintenance ■ The vehicle has a maintenance-free type immobilizer system. Conditions that may cause the system to malfunction ■ If the grip portion of the key is in contact with a metallic object ● If the key is in close proximity to or touching a key registered to the security ●...
Page 74: Alarm
1-2. Theft deterrent system Alarm The alarm The alarm uses light and sound to give an alert when an intrusion is detected. The alarm is triggered in the following situations when the alarm is set: ● A locked door or trunk is unlocked or opened in any way other than using the entry function, wireless remote control or mechanical key.
Page 75 1-2. Theft deterrent system System maintenance ■ The vehicle has a maintenance-free type alarm system. Items to check before locking the vehicle ■ To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: Nobody is in the vehicle. ●...
Page 76: Theft Prevention Labels
1-2. Theft deterrent system Theft prevention labels These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recov- ery of parts from stolen vehicles. Do not remove under penalty of law.
Page 77: 2. Fuel Cell Vehicle
Fuel cell system Fuel cell vehicle Fuel cell vehicle characteristics ....78 Fuel cell vehicle precautions ....... 82 Advice for driving fuel cell vehicles ......94...
Page 78: Fuel Cell Vehicle Characteristics
2. Fuel cell vehicle Fuel cell vehicle characteristics Fuel cell vehicles efficiently use electricity, which is generated by a chemical reaction between hydrogen and oxygen in a fuel cell stack, and electricity charged in a traction battery to drive the electric motor (traction motor). The fuel is H (compressed hydrogen gas), so the exhaust is only water and water vapor.
Page 79 2. Fuel cell vehicle Driving the vehicle The electric motor (traction motor) allows smooth, powerful takeoff and acceleration. This vehicle drives similarly to a gasoline vehicle without any special actions by the driver. (→P. 158) As there are no engine sounds and the vehicle is quiet, operation noises unique to fuel cell vehicle components may be heard.
Page 80 2. Fuel cell vehicle ■ Sounds unique to the fuel cell vehicle Due to the design of your fuel cell vehicle, there are various relays, valves and pumps which under normal driving conditions will produce sounds. This is a normal characteristic of the vehicle and does not indicate a malfunction. Furthermore, way of hearing may differ based on usage environment or con- dition.
Page 81 P and apply the parking brake when parked. ■ Maintenance, repair, recycling, and disposal Contact your Toyota dealer regarding maintenance, repair, recycling, and dis- posal. Do not dispose of the vehicle or any of its components yourself.
Page 82: Fuel Cell Vehicle Precautions
2. Fuel cell vehicle Fuel cell vehicle precautions Hydrogen-related components The fuel cell vehicle has hydrogen tanks (10150 psi [70 MPa, 714 kgf/cm , 700 bar]), fuel cell stack, and hydrogen pipelines as hydrogen-related components. Pay attention to all warning labels attached to the vehicle.
Page 83 2. Fuel cell vehicle High-voltage and high-temperature components The fuel cell vehicle has high-voltage components (about 650 V maxi- mum) such as a fuel cell stack, traction battery, power control unit, high-voltage cables (which are distinguished from low-voltage cables by their orange covers), electric motor (traction motor), etc., and high- temperature parts such as the radiator for cooling.
Page 84 Also, the fuel supply is stopped from the hydrogen tank valves. If the emergency shut off system activates, your vehicle will not restart. To restart the fuel cell system, contact your Toyota dealer. Fuel cell warning message A message is automatically displayed when a malfunction occurs in the fuel cell system or an improper operation is attempted.
Page 85 If “Hydrogen Leakage Detected Visit Your Dealer” is displayed on the multi-information display A small amount of hydrogen gas may be leaking. Have the vehicle inspected immediately at the nearest Toyota dealer. ■ If “FC System Shutdown due to Hydrogen Leakage Stop Your Vehicle in a Safe Place and Contact Your Dealer”...
Page 86 • Salt water gets into the air cleaner filter It is recommended to replace the air cleaner filter and clean the surround- ing components. Have the vehicle inspected at your Toyota dealer • The number of times the fuel cell system is started and stopped is exces- sively high •...
Page 87 ● Never add water or other coolants to the fuel cell stack cooling system, as they will cause permanent damage. ● Consult your Toyota dealer for replenishing or changing the fuel cell stack coolant. ■ Ion filter ●...
Page 88 2. Fuel cell vehicle ■ Power output restriction When the power output is restricted, the vehicle may fail to accelerate or even decelerate, even though the accelerator pedal is depressed. If a safe driving speed cannot be maintained, stop the vehicle in a safe place away from the traffic.
Page 89 2. Fuel cell vehicle ■ Hydrogen Gas Characteristics ● Hydrogen gas ignites more easily than gasoline. However, it is lighter than air and disperses quickly. So even if hydrogen were to leak from the system, it would quickly dilute until it is no longer flammable. ●...
Page 90 If a large amount of hydrogen gas leaking is noticed, turn off the power ● switch, exit the vehicle, and stay far away from it. Display warning signs and keep sources of fire away from the vehicle. If possible, get assistance. When the above is done, immediately contact your Toyota dealer.
Page 91 Never touch the service plugs that are ● installed on the fuel cell stack and the traction battery. The service plugs are used to block high-voltages from the fuel cell stack and the traction battery during maintenance or repair at your Toyota dealer.
Page 92 Display warning signs and keep sources of fire away from the vehicle. If possible, get assistance. When the above is done, immediately contact your Toyota dealer. Do not touch the high-voltage parts, cables (orange), or connectors.
Page 93 When disposing of your vehicle, the traction battery must be disposed by your Toyota dealer, or a qualified service shop. If the traction battery is not disposed of properly, it may cause electric shock that can result in death or serious injury.
Page 94: Advice For Driving Fuel Cell Vehicles
2. Fuel cell vehicle Advice for driving fuel cell vehicles To maximize fuel economy and range, pay attention to the fol- lowing: ◆ Fuel cell system indicator usage Maintaining the fuel cell system indicator to Eco area on the multi-information display can extend your driving range. (→P. 110) ◆...
Page 95 2. Fuel cell vehicle ◆ Using Eco drive mode Using Eco drive mode (→P. 181) makes torque generation less aggressive than normal when stepping on the accelerator pedal, leading to improvement in fuel economy. Also, is displayed on the air conditioning screen, indicating the switch to ECO HEAT/COOL mode (→P.
Page 96 2. Fuel cell vehicle...
Page 97 Instrument cluster Instrument cluster Warning lights and indicators ......98 Gauges and meters ..102 Multi-information display ... 107...
Page 98: Indicators
3. Instrument cluster Warning lights and indicators The warning lights and indicators inform the driver of the status of the vehicle’s various systems. For the purpose of explanation, the following illustration dis- plays all warning lights and indicators illuminated.
Page 99 3. Instrument cluster Warning lights Warning lights inform the driver of malfunctions in the indicated vehi- cle’s systems. Hydrogen leak warning Slip indicator (→P. 370) light (→P. 369) Brake system warning Parking brake warning light (→P. 369) light (→P. 371) Charging system Open door warning light warning light (→P.
Page 100 There may be a malfunction in a system if the lights do not come on, or turn off. Have the vehicle inspected by your Toyota dealer. : The light flashes to indicate a malfunction.
Page 101 Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 102: Gauges And Meters
3. Instrument cluster Gauges and meters Main display Displays the speedometer, fuel gauge, etc. (→P. 102) Multi-information display Presents the driver with a variety of vehicle data. Displays warning messages in case of a malfunction. (→P. 376) Shift position indicator Displays the selected shift position.
Page 103 3. Instrument cluster ECO MODE indicator and POWER MODE indicator Displays the selected driving mode. (→P. 181) Power restriction indicator Blue: The fuel cell system output power is restricted, because the coolant temperature is low. Amber: The fuel cell system output power is restricted, because the coolant temperature is high.
Page 104 3. Instrument cluster Changing the display Switches between odometer and trip meter displays. When the trip meter is displayed, pressing and holding the button will reset the trip meter. Instrument panel light control The brightness of the Instrument panel lights can be adjusted. Brighter Darker Setting split screen on the main display...
Page 105 3. Instrument cluster Power meter Current fuel consumption Traction battery status ■ The meters and display illuminate when The power switch is in ON mode. ■ Instrument panel brightness adjustment The instrument panel brightness levels when the tail lights are on and off can be adjusted individually.
Page 106 When “--” or “E” is displayed, the system may be malfunctioning. ● Take your vehicle to your Toyota dealer. Liquid crystal display ■ Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem continuing to use the display.
Page 107: Multi-Information Display
3. Instrument cluster Multi-information display The multi-information display presents the driver with a variety of vehicle data. Displays the following informa- tion when an icon is selected. (→P. 108) Some of the information may be displayed automatically depending on the situation. Drive information Select to display various drive data.
Page 108 3. Instrument cluster Settings display When using each equipment, it is possible to toggle the switch and change the settings of the meter display. • Intuitive parking assist (→P. 223) • BSM (Blind Spot Monitor) (→P. 245) • Clock (→P. 280) •...
Page 109 3. Instrument cluster When the vehicle is powered by the fuel cell stack and traction battery When the vehicle is charging the traction bat- tery When there is no energy flow Traction battery status Full These images are examples only, and may vary slightly from actual conditions.
Page 110 3. Instrument cluster ■ Fuel cell system indicator and ECO Score The output power of the fuel cell system, regeneration level display, and the ECO driving is scored and displayed. Charge area Shows that energy is being recovered via the regenera- tive brake.
Page 111 3. Instrument cluster ■ Fuel consumption record To toggle through the items, press on the meter control switches (→P. 108) to select the tab and then press either  1-minute fuel consumption Average fuel consumption in the past 15 minutes, displayed in 1-minute intervals ...
Page 112 3. Instrument cluster ■ Drive monitor Driving time Displays the amount of time since starting the fuel cell system or resetting Average vehicle speed Displays the average vehicle speed since starting fuel cell system or reset- ting Average fuel consumption Displays the average fuel consumption since starting the fuel cell system or resetting...
Page 113 3. Instrument cluster ■ ECO diary To toggle through the items, press on the meter control switches (→P. 108) to select the tab and then press either  Daily history Press either of the meter control switches to scroll through the days displayed. ...
Page 114 3. Instrument cluster Suspension of the settings display ■ In the following situations, the settings display using the meter control switches will be suspended. When a warning message appears on the multi-information display ● When the vehicle begins to move ●...
Page 115 Operation of each component 4-1. Key information Keys ........116 4-2. Opening, closing and locking the doors Doors ........ 120 Trunk......... 126 Smart key system ..... 131 4-3. Adjusting the seats Front seats ......138 Driving position memory ... 140 Head restraints....
Page 116: Key Information Keys
Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the windows (→P. 120) Opens the trunk (→P. 126) Sounds the alarm (→P. 117) : This setting must be customized at your Toyota dealer.
Page 117 ■ If you lose your mechanical keys New genuine mechanical keys can be made by your Toyota dealer using the other mechanical key and the key number stamped on your key number plate. Keep the plate in a safe place such as your wallet, not in the vehicle.
Page 118 ■ Confirmation of the registered key number The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details. ■ If a wrong key is used The key cylinder rotates freely to isolate inside mechanism.
Page 119 Toyota dealer. When an electronic key is lost ■ If the electronic key remains lost, the risk of vehicle theft increases signifi- cantly. Visit your Toyota dealer immediately with all remaining electronic keys that were provided with your vehicle.
Page 120: Locking The Doors Doors
Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Press and hold to open the win- dows. : This setting must be customized at your Toyota dealer.
Page 121 4-2. Opening, closing and locking the doors ■ Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Windows: A buzzer sounds to indicate that the windows are opening. ■...
Page 122 4-2. Opening, closing and locking the doors Unlocking and locking the doors from the inside ◆ Door lock switches Locks all the doors Unlocks all the doors ◆ Inside lock buttons Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Page 123 4-2. Opening, closing and locking the doors Rear door child-protector lock The door cannot be opened from inside the vehicle when the lock is set. Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
Page 124 4-2. Opening, closing and locking the doors ■ Switching the door unlock function It is possible to set which doors the entry function unlocks using the wireless remote control. Turn the power switch off. When the indicator light on the key surface is not on, press and hold for approximately 5 seconds while pressing and holding The setting changes each time an operation is performed, as shown below.
Page 125 4-2. Opening, closing and locking the doors Conditions affecting the operation of the smart key system or wireless ■ remote control →P. 134 Customization ■ Settings (e.g. unlocking function using a key) can be changed. (Customizable features: →P. 435) WARNING To prevent an accident ■...
Page 126: Trunk
4-2. Opening, closing and locking the doors Trunk The trunk can be opened using the trunk opener, entry function or wireless remote control. Opening the trunk from inside the vehicle Press the trunk opener switch. Opening the trunk from outside the vehicle ◆...
Page 127 4-2. Opening, closing and locking the doors When closing the trunk Using the trunk grip, lower the trunk without applying force to the side and push the trunk down from the outside to close it. Luggage security system To protect luggage stored in the trunk against theft, the luggage secu- rity system can be set to on.
Page 128 4-2. Opening, closing and locking the doors ■ Trunk light The trunk light turns on when the trunk is opened. ■ Function to prevent the trunk being locked with the electronic key inside ● When all doors are locked, closing the trunk lid with the electronic key left inside the trunk will sound an alarm.
Page 129 4-2. Opening, closing and locking the doors P. 117 WARNING Observe the following precautions. Failure to do so may result in death or serious injury. Before driving ■ Make sure that the trunk lid is fully closed. If the trunk lid is not fully closed, ●...
Page 130 Do not attach any accessories other than genuine Toyota parts to the trunk ● lid. Such additional weight on the trunk lid may cause the lid to suddenly...
Page 131: Smart Key System
4-2. Opening, closing and locking the doors Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. The driver should always carry the electronic key. ● Locks and unlocks the doors (→P. 120) ●...
Page 132 4-2. Opening, closing and locking the doors ■ Effective range (areas within which the electronic key is detected) When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of an outside door handle.
Page 133 4-2. Opening, closing and locking the doors ■ When “Smart Entry & Start System Malfunction See Owner’ Manual” will be displayed on the multi-information display The system may be malfunctioning. Have the vehicle inspected by your Toy- ota dealer immediately. ■...
Page 134 4-2. Opening, closing and locking the doors ■ Conditions affecting operation The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and immobilizer system from operating properly.
Page 135 4-2. Opening, closing and locking the doors ■ Note for the entry function ● Even when the electronic key is within the effective range (detection areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
Page 136 4-2. Opening, closing and locking the doors ● The lock sensor may not work properly if it comes into contact with ice, snow, mud, etc. Clean the lock sensor and attempt to operate it again. ● A sudden approach to the effective range or door handle may prevent the doors from being unlocked.
Page 137 (→P. 132) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of the emitted radio waves.
Page 138: Adjusting The Seats Front Seats
4-3. Adjusting the seats Front seats Adjustment procedure Seat position adjustment Vertical height adjustment Seatback angle adjustment Lumbar support adjustment Seat cushion (front) angle adjustment ■ Power easy access system The driver’s seat and steering wheel move in accordance with power switch mode and the driver’s seat belt condition.
Page 139 4-3. Adjusting the seats WARNING When adjusting the seat position ■ Take care when adjusting the seat position to ensure that other passen- ● gers are not injured by the moving seat. Do not put your hands under the seat or near the moving parts to avoid ●...
Page 140: Driving Position Memory
4-3. Adjusting the seats Driving position memory This feature automatically adjusts the front seats, steering wheel and outside rear view mirrors to make entering and exiting the vehicle easier or to suit your preferences. Power easy access system The seat and steering wheel are automatically adjusted to allow the driver to enter and exit the vehicle easily.
Page 141 4-3. Adjusting the seats Driving position memory Your preferred driving position (the position of the driver’s seat, steer- ing wheel and outside rear view mirrors) can be recorded and recalled by pressing a button. Two different driving positions can be recorded into memory. ■...
Page 142 4-3. Adjusting the seats ■ To stop the position recall operation part-way through Perform any of the following: ● Press the “SET” button. ● Press button “1” or “2”. ● Operate any of the seat adjustment switches (only cancels seat position recall).
Page 143 4-3. Adjusting the seats While pressing the recalled button, press and hold the door lock switch (either lock or unlock) until the buzzer sounds. If the button could not be regis- tered, the buzzer sounds contin- uously approximately 3 seconds. ■...
Page 144 4-3. Adjusting the seats Recalling the driving position using the memory recall function ■ Different driving positions can be registered for each electronic key. There- ● fore, the driving position that is recalled may be different depending on the key being carried. If a door other than the driver’s door is unlocked with the smart key system, ●...
Page 145: Head Restraints
4-3. Adjusting the seats Head restraints Head restraints are provided for all seats. Front seats  Vertical adjustment Pull the head restraint up. Down Push the head restraint down while pressing the lock release button. Lock release button  Horizontal adjustment The position of the head restraint can be adjusted forward in 4 stages.
Page 146 4-3. Adjusting the seats Removing the head restraints ■ Pull the head restraint up while pressing Lock the lock release button. release If the head restraint touches the ceiling, button making the removal difficult, change the seat height or angle. (→P. 138) Installing the head restraints ■...
Page 147 4-4. Adjusting the steering wheel and mirrors Steering wheel Adjustment procedure Operating the switch moves the steering wheel in the following direc- tions: Down Toward the driver Away from the driver Horn To sound the horn, press on or close to the mark.
Page 148 4-4. Adjusting the steering wheel and mirrors WARNING Caution while driving ■ Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.
Page 149: Inside Rear View Mirror
4-4. Adjusting the steering wheel and mirrors Inside rear view mirror The rear view mirror’s position can be adjusted to enable suffi- cient confirmation of the rear view. Adjusting the height of rear view mirror The height of the rear view mirror can be adjusted to suit your driving posture.
Page 150 4-4. Adjusting the steering wheel and mirrors To prevent sensor error ■ To ensure that the sensors operate prop- erly, do not touch or cover them. WARNING Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.
Page 151: Outside Rear View Mirrors
4-4. Adjusting the steering wheel and mirrors Outside rear view mirrors Adjustment procedure To select a mirror to adjust, turn the switch. Left Right To adjust the mirror, operate the switch. Right Down Left Folding and extending the mirrors Folds the mirrors Extends the mirrors Putting the outside rear view mirror folding switch in the neu-...
Page 152 4-4. Adjusting the steering wheel and mirrors Linked mirror function when reversing When the mirror select switch is in the “L” or “R” position, the outside rear view mirrors will automatically angle downwards when the vehicle is reversing in order to give a better view of the ground. To disable this function, move the mirror select switch to the neutral position (between “L”...
Page 153 4-4. Adjusting the steering wheel and mirrors Using automatic mode in cold weather ■ When automatic mode is used in cold weather, the door mirror could freeze up and automatic stowing and return may not be possible. In this event, remove any ice and snow from the door mirror, then either operate the mirror using manual mode or move the mirror by hand.
Page 154: The Windows Power Windows
4-5. Opening and closing the windows Power windows Opening and closing procedures The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows: Closing One-touch closing Opening One-touch opening : To stop the window partway, oper- ate the switch in the opposite direc- tion.
Page 155 ● The power windows can be opened using the wireless remote control. (→P. 120) : These settings must be customized at your Toyota dealer. ■ Power windows open warning buzzer The buzzer sounds and a message is shown on the multi-information display in the instrument cluster when the power switch is turned off and the driver’s...
Page 156 4-5. Opening and closing the windows WARNING Observe the following precautions. Failure to do so may result in death or serious injury. Closing the windows ■ The driver is responsible for all the power window operations, including the ● operation for the passengers. In order to prevent accidental operation, especially by a child, do not let a child operate the power windows.
Page 157 Driving 5-1. Before driving 5-3. Operating the lights and wipers Driving the vehicle..... 158 Headlight switch....187 Cargo and luggage ... 166 Automatic High Beam ..190 Vehicle load limits ..... 169 Windshield wipers and Trailer towing..... 170 washer ......195 Dinghy towing ....
Page 158: Driving The Vehicle
5-1. Before driving Driving the vehicle The following procedures should be observed to ensure safe driving: Starting the fuel cell system →P. 172 Driving With the brake pedal depressed, shift the shift position to D. (→P. 179) Check that the shift position indicator shows D. Release the parking brake.
Page 159 5-1. Before driving ■ When starting off on an uphill The hill-start assist control will activate. (→P. 232) ■ For fuel-efficient driving Keep in mind that fuel cell vehicles are similar to conventional vehicles, and it is necessary to refrain from activities such as sudden acceleration. (→P. 94) ■...
Page 160 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or whenever the parking brake shoes and/or drum are replaced. Have your Toyota dealer per- form the bedding down operation.
Page 161 5-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. When starting the vehicle ■ Always keep your foot on the brake pedal while stopped with the “READY” indicator is illuminated. This prevents the vehicle from creeping. When driving the vehicle ■...
Page 162 5-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. When driving the vehicle ■ Do not drive in excess of the speed limit. Even if the legal speed limit per- ●...
Page 163 If you hear a squealing or scraping noise (brake pad wear limit indica- ■ tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed.
Page 164 5-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. When the vehicle is parked ■ Do not leave a door or window open if the curved glass is coated with a ●...
Page 165 Fuel cell system damage caused by water immersion ● In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: Fuel cell system ● Brake function ●...
Page 166: Cargo And Luggage
Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 169) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.
Page 167 5-1. Before driving Calculation formula for your vehicle Cargo capacity Total load capacity (vehicle capacity weight) (→P. 416) When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb.
Page 168 5-1. Before driving WARNING Things that must not be carried in the trunk ■ The following things may cause a fire if loaded in the trunk: Vehicle receptacle containing gasoline ● Aerosol cans ● Storage precautions ■ Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident.
Page 169: Vehicle Load Limits
Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. ◆ Towing capacity Toyota does not recommend towing a trailer with your vehicle. ◆ Cargo capacity Cargo capacity may increase or decrease depending on the weight and the number of occupants.
Page 170: Trailer Towing
Trailer towing Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicy- cle, etc. Your vehicle is not designed for trailer towing or for the...
Page 171: Dinghy Towing
5-1. Before driving Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE To avoid serious damage to your vehicle ■ Do not tow your vehicle with four wheels on the ground.
Page 172: Driving Procedures Power Switch
5-2. Driving procedures Power switch Performing the following operations when carrying the elec- tronic key on your person starts the fuel cell system or changes power switch modes. Starting the fuel cell system Check that the parking brake is set. Firmly depress the brake pedal.
Page 173 5-2. Driving procedures Stopping the fuel cell system Stop the vehicle completely. Set the parking brake. (→P. 186) Press the P position switch. (→P. 180) Check that the shift position indica- tor shows P. (→P. 179) Press the power switch. The meter display will turn off, indicating the fuel cell system has stopped.
Page 174 5-2. Driving procedures Changing power switch modes Modes can be changed by pressing the power switch with brake pedal released. (The mode changes each time the switch is pressed.) The emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used.
Page 175 5-2. Driving procedures ■ Starting the fuel cell system in cold temperatures ● When the power switch is pressed and the fuel cell system starts (→P. 172) during cold temperatures, the fuel cell stack is quickly warmed up using the waste heat during power generation.
Page 176 ■ If the “READY” indicator does not come on In the event that the “READY” indicator does not come on even after perform- ing the proper procedures for starting the vehicle, contact your Toyota dealer immediately. ■ If the fuel cell system is malfunctioning...
Page 177 The power switch will not be able to be turned off. In this occurs, the switch can be turned off by applying the parking brake. If the system malfunctions, have your vehicle serviced by your Toyota dealer immediately. If the smart key system has been deactivated in a customized setting ■...
Page 178 When starting the fuel cell system ■ If the fuel cell system becomes difficult to start, have your vehicle checked by your Toyota dealer immediately. Symptoms indicating a malfunction with the power switch ■ If the power switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction.
Page 179: Transmission
5-2. Driving procedures Transmission Shifting the shift lever Shift lever Operate the shift lever gently and ensure correct shifting operation. Release the shift lever after each shifting operation to allow it return to the position. When shifting to the D or R positions, move the shift lever along the shift gate.
Page 180 5-2. Driving procedures Shift position purpose Shift position Objective or function Parking the vehicle/starting the fuel cell system Reversing Neutral Normal driving P position switch The shift position can be changed to P through the use of the P posi- tion switch.
Page 181 5-2. Driving procedures Selecting a drive mode The following modes can be selected to suit driving conditions. ■ Eco drive mode/Power mode Eco drive mode Suitable for improving the fuel economy, because the torque corresponding to the accelerator pedal depres- sion amount can be gener- ated more smoothly than it is in normal conditions.
Page 182 5-2. Driving procedures ■ For the shift positions ● When the power switch is off, the shift position cannot be changed. ● When the power switch is in ON mode (the fuel cell system is not operating), the shift position can only be changed to N. The shift position will be changed to N even if the shift position is shifted to D or R and held in that position.
Page 183 For the shift lever ■ Do not remove the shift lever knob or use anything but a genuine Toyota shift lever knob. Also, do not hang anything on the shift lever. Doing so could prevent the shift lever from returning to position, causing unexpected accidents to occur when the vehicle is in motion.
Page 184 If any of the following situations occurs, shift control system malfunctions are possible. Immediately stop the vehicle in a safe place on level ground, apply the park- ing brake, and then contact your Toyota dealer. When a warning message indicating malfunction appears on the multi- ●...
Page 185: Turn Signal Lever
5-2. Driving procedures Turn signal lever Operating instructions Right turn Lane change to the right (move the lever partway and release The right hand signals will flash 3 times. Lane change to the left (move the lever partway and release The left hand signals will flash 3 times.
Page 186: Parking Brake
5-2. Driving procedures Parking brake Operating instructions To set the parking brake, fully depress the parking brake pedal with your left foot while depress- ing the brake pedal with your right foot. (Depressing pedal again releases the parking brake.) Parking brake engaged warning buzzer ■...
Page 187: And Wipers Headlight Switch
5-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Operating instructions Turning the end of the lever turns on the lights as follows: The side marker, tail, license plate, daytime running lights, instru- ment panel and switch lights turn on.
Page 188 5-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off.
Page 189 5-3. Operating the lights and wipers Automatic light off system ■ When the headlights are on: The headlights and tail lights turn off 30 sec- ● onds after a door is opened and closed if the power switch is turned to ACCESSORY mode or turned off.
Page 190: Automatic High Beam
5-3. Operating the lights and wipers Automatic High Beam The Automatic High Beam uses an in-vehicle camera sensor to assess the brightness of streetlights, the lights of oncoming and preceding vehicles, etc., and automatically turns high beam on or off as necessary. Activating the Automatic High Beam system Push the lever away from you with the headlight switch in...
Page 191 5-3. Operating the lights and wipers High beam automatic turning on or off conditions When all of the following conditions are fulfilled, high beam will be automatically turned on: ● Vehicle speed is above approximately 21 mph (34 km/h). ● The area ahead of the vehicle is dark. ●...
Page 192 5-3. Operating the lights and wipers ■ The Automatic High Beam can be operated when The power switch is in ON mode. ■ Camera sensor detection information ● High beam may not be automatically turned off in the following situations: •...
Page 193 5-3. Operating the lights and wipers In the situations below, the system may not be able to correctly detect the ● surrounding brightness levels, and may flash or expose nearby pedestrians to the high beam. Therefore, you should consider turning the high beams on or off manually rather than relying on the Automatic High Beam system.
Page 194 Do not install a parking tag or any other accessories near or around the ● camera sensor. Do not overload the vehicle. ● Do not modify the vehicle. ● If the windshield needs to be replaced, contact your Toyota dealer. ●...
Page 195: Windshield Wipers And Washer
5-3. Operating the lights and wipers Windshield wipers and washer Operating the wiper lever When “AUTO” is selected, the wipers will operate automatically when the sensor detects falling rain. The system automatically adjusts wiper timing in accordance with rain volume and vehicle speed. Rain-sensing operation Low speed operation High speed operation...
Page 196 5-3. Operating the lights and wipers Washer/wiper dual operation Wipers will automatically operate a couple of times after the washer squirts. The windshield wipers and washers can be operated when ■ The power switch is in ON mode. Effects of vehicle speed on wiper operation ■...
Page 197 Do not operate the switch continually as the washer fluid pump may over- heat. When a nozzle becomes blocked ■ In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged. To prevent 12-volt battery discharge ■...
Page 198: Refueling Opening The Fuel Door
SAE protocols. ● Refer to the Mirai Station Finder Application in Entune, www.toyota.com, or call 800-331-4331. ● Observe any notices or instructions shown at hydrogen stations. ● The filling time and amount of fuel may depend on outside tem- perature and the equipment at that hydrogen station.
Page 199 If you notice anything unusual about the vehicle receptacle, please notify ● your Toyota dealer. If you notice anything unusual with the hydrogen dispenser or hydrogen ● gas nozzle, please notify the hydrogen station operator. Contact informa-...
Page 200 5-4. Refueling Opening the fuel door Press the fuel door opener switch to release the lock. If the “READY” indicator is on or the power switch is in ON mode, the fuel door will not be unlocked. Press the center part of the rear edge of the fuel door.
Page 201 5-4. Refueling ■ If “Open H2 Filler Door in a Safe Place when Vehicle is Powered OFF” is displayed on the multi-information display Stop the vehicle in a safe place and press the fuel door opener switch once more with the following procedure: Shift the shift position to P.
Page 202 If the warning message on the multi-information display turns off at this time, there is no malfunction. However, if the display continues to show, the sensor may be damaged. Have the vehicle inspected by your Toyota dealer.
Page 203: Control
5-5. Using the driving support systems Dynamic radar cruise control Summary of functions Without accelerator pedal operation by the driver, in vehicle-to-vehicle distance control mode, the vehicle automatically accelerates and decelerates in accordance to the changes in speed of the preceding vehicle.
Page 204 5-5. Using the driving support systems Driving in vehicle-to-vehicle distance control mode This mode employs a radar sensor to detect the presence of vehicles up to approximately 400 ft. (120 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to maintain a suit- able following distance from the vehicle ahead.
Page 205 5-5. Using the driving support systems Example of follow-up cruising When following a preceding vehicle that is driving slower than the set speed The system continues follow-up cruising while adjusting for changes in the speed of the vehicle ahead in order to maintain the vehicle-to-vehicle dis- tance set by the driver.
Page 206 5-5. Using the driving support systems Adjusting the set speed To change the set speed, operate the lever until the desired set speed is displayed. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direc- tion.
Page 207 5-5. Using the driving support systems Changing the vehicle-to-vehicle distance (vehicle-to-vehicle dis- tance control mode) Pressing the button changes the Preceding vehicle-to-vehicle distance as fol- vehicle mark lows: Long Medium Short The vehicle-to-vehicle distance is set automatically to long mode when the power switch is turned to ON mode.
Page 208 5-5. Using the driving support systems Canceling and resuming the speed control Pulling the lever toward you cancels the speed control. The speed setting is also canceled when brake pedal depressed. Pushing the lever up resumes the speed control and returns vehicle speed to the set speed.
Page 209 5-5. Using the driving support systems Selecting constant speed control mode When constant speed control mode is selected, your vehicle will main- tain a set speed without controlling the vehicle-to-vehicle distance. Select this mode only when vehicle-to-vehicle distance control mode does not function correctly due to dirt, etc.
Page 210 Pre-collision braking is activated. ● Br mode shift operation was done. If vehicle-to-vehicle distance control mode is automatically canceled for any other reason, there may be a malfunction in the system. Contact your Toyota dealer. ■ Automatic cancelation of constant speed control...
Page 211 5-5. Using the driving support systems ■ Radar sensor and grille cover Always keep the sensor and grille cover clean to ensure that the vehicle-to- vehicle distance control mode operates properly. (Some obstructions, such as snow, ice and plastic objects, cannot be detected by the obstruction sen- sor.) Dynamic radar cruise control is canceled if an obstruction is detected.
Page 212 5-5. Using the driving support systems WARNING Before using dynamic radar cruise control ■ Do not overly rely on vehicle-to-vehicle distance control mode. Be aware of the set speed. If automatic deceleration/acceleration is not appropriate, adjust the vehicle speed, as well as the distance between your vehicle and vehicles ahead by applying the brakes, etc.
Page 213 5-5. Using the driving support systems WARNING Situations unsuitable for dynamic radar cruise control ■ Do not use dynamic radar cruise control in any of the following situations. Doing so may result in inappropriate speed control and could cause an acci- dent resulting in death or serious injury.
Page 214 5-5. Using the driving support systems WARNING Motorcycles traveling in the same lane ● When water or snow thrown up by the surrounding vehicles hinders the ● detecting of the sensor When your vehicle is pointing upwards ● (caused by a heavy load in the trunk, etc.) Conditions under which the vehicle-to-vehicle distance control mode ■...
Page 215 Do not attach accessories or stickers to the sensor, grille cover or sur- ● rounding area. Do not modify or paint the sensor and grille cover. ● If the radar sensor needs to be replaced, contact your Toyota dealer. ●...
Page 216: Lda (Lane Departure Alert)
5-5. Using the driving support systems LDA (Lane Departure Alert) Summary of function While driving on a road that has lane markers, this system recognizes the lane markers using a camera sensor and alerts the driver when the vehicle deviates from its lane. If the system judges that the vehicle has deviated from its lane, it alerts the driver using a buzzer and indications on the multi-informa- tion display.
Page 217 5-5. Using the driving support systems Turning the LDA system on Press the LDA switch to activate the system. The LDA indicator and lane lines will come on. Press the switch again to deacti- vate the LDA system. The LDA system will remain on or off even if the power switch is turned to ON mode.
Page 218 5-5. Using the driving support systems Indication on the multi-information display When the inside of both lane lines turn white: Indicates that both right and left lane markers are recognized. If the vehicle deviates from the lane, the lane line on the side the vehicle has deviated from will flash in yellow.
Page 219 5-5. Using the driving support systems ■ Temporary cancelation of the LDA system functions If any of the following occurs, the LDA system functions will be temporarily canceled. The functions will resume after the necessary operating conditions have returned. ● The turn signal lever is operated.
Page 220 5-5. Using the driving support systems ■ Conditions in which the function may not operate correctly In the following situations, the camera sensor may be unable to recognize lane markers causing the lane departure warning function to operate incor- rectly. However, this does not indicate a malfunction. ●...
Page 221 5-5. Using the driving support systems Warning messages for the LDA system ■ Warning messages are used to indicate a system malfunction or to inform the driver of the need for caution while driving. If a warning message is shown on the multi-information display, read the message and follow the instructions.
Page 222 ● Do not modify the suspension. ● If any suspension parts need to be replaced, contact your Toyota dealer. Do not install or place anything on the hood or the grille. Also, do not install ● a grille guard (bull bars, kangaroo bar, etc.).
Page 223: Intuitive Parking Assist
5-5. Using the driving support systems Intuitive parking assist The distance from your vehicle to nearby obstacles when paral- lel parking or maneuvering into a garage is measured by the sensors and communicated via the displays and a buzzer. Always check the surrounding area when using this system. Types of sensors Front corner sensors Rear corner sensors...
Page 224 5-5. Using the driving support systems Turning the intuitive parking assist system on ON (activate)/OFF (deactivate) can be changed by the [set- tings display] for the Multi-information Display (→P. 107) Press either on the meter control switches (→P. 108) and select Each press of of the meter control switches, changes ON and OFF.
Page 225 5-5. Using the driving support systems Display When the sensors detect an obstacle, the following displays inform the driver of the position and distance to the obstacle. ■ Multi-information display Front corner sensor opera- tion Rear corner sensor operation Rear center sensor operation ■...
Page 226 5-5. Using the driving support systems Sensor detection display, obstacle distance ■ Distance display Sensors that detect an obstacle will illuminate continuously or blink. Approximate distance to obstacle Display Rear corner sensor/rear Front corner sensor center sensor Rear center sensor only: —...
Page 227 5-5. Using the driving support systems ■ Buzzer operation and distance to an obstacle A buzzer sounds when the sensors are operating. ● The buzzer sounds faster as the vehicle approaches an obstacle. When the vehicle comes within the following distance of the obstacle, the buzzer sounds continuously.
Page 228 ON mode. Press the “APPS” button. Select “Setup” on the “Apps” screen and select “Vehicle”. Select “TOYOTA Park Assist Settings” on the screen. Select the desired item. The buzzer sounds volume can be adjusted.
Page 229 • The area directly under the bumpers is not detected. • If obstacles draw too close to the sensor. • A non-genuine Toyota suspension (lowered suspension etc.) is installed. • People may not be detected if they are wearing certain types of clothing.
Page 230 Depending on the malfunction of the sensor, the device may not be working normally. Have the vehicle inspected by your Toyota dealer. Certification for the intuitive parking assist ■ This device complies with Part 15 of the FCC Rules. Operation is subject to...
Page 231 When using intuitive parking assist ■ In the following situations, the system may not function correctly due to a sensor malfunction, etc. Have the vehicle checked by your Toyota dealer. The intuitive parking assist operation display flashes, and a buzzer sounds ●...
Page 232: Driving Assist Systems
5-5. Using the driving support systems Driving assist systems To help enhance driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supple- mentary and should not be relied upon too heavily when operat- ing the vehicle.
Page 233 5-5. Using the driving support systems ◆ EPS (Electric Power Steering) Employs an electric motor to reduce the amount of effort needed to turn the steering wheel ◆ PCS (Pre-Collision System) →P. 238 ◆ BSM (Blind Spot Monitor) →P. 245 When the TRAC/VSC/ABS systems are operating The slip indicator will flash while the TRAC/VSC/ABS systems are...
Page 234 When the message is displayed on the multi-information display show- ing that TRAC has been disabled even if has not been pressed TRAC and hill-start assist control cannot be operated. Contact your Toyota dealer. ■ Sounds and vibrations caused by the ABS, brake assist, VSC, TRAC and...
Page 235 5-5. Using the driving support systems ■ Reduced effectiveness of the EPS system The effectiveness of the EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the fuel cell system off.
Page 236 5-5. Using the driving support systems WARNING The ABS does not operate effectively when ■ The limits of tire gripping performance have been exceeded (such as ● excessively worn tires on a snow covered road). The vehicle hydroplanes while driving at high speed on wet or slick roads. ●...
Page 237 The ABS, TRAC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. Handling of tires and the suspension ■...
Page 238: Pcs (Pre-Collision System)
5-5. Using the driving support systems PCS (Pre-Collision System) When the radar sensor detects possibility of a frontal collision, brakes are automatically engaged to lessen impact as well as vehicle damage. The alert timing for the pre-collision system can be changed or turned on/off, as necessary, by operating the switch.
Page 239 5-5. Using the driving support systems Changing the pre-collision system ■ Changing the alert timing of the pre-collision system Each time the PCS switch is pressed, the response to the distance changes as follows. Middle Near : Default setting ■ Turning off the pre-collision system Press the PCS switch for 3 sec- onds or more seconds.
Page 240 5-5. Using the driving support systems Radar sensor The radar sensor detects vehi- cles or other obstacles on or near the road ahead and determines whether a collision is imminent based on the position, speed, and heading of the obstacles. ■...
Page 241 5-5. Using the driving support systems ■ Conditions that may trigger the system even if there is no possibility of a collision In any of the following situations where the frontal area of the radar sensor is interrupted, the radar sensor may detect possibility of a frontal collision and the system may be activated.
Page 242 5-5. Using the driving support systems ■ Automatic cancelation of the pre-collision system When a malfunction occurs due to sensor contamination, etc., that results in the sensors being unable to detect obstacles, the pre-collision system will be automatically disabled. In this case, the system will not activate even if there is a collision possibility.
Page 243 Do not attach accessories or stickers to the sensor, grille cover or sur- ● rounding area. Do not modify or paint the sensor and grille cover. ● If the radar sensor needs to be replaced, contact your Toyota dealer. ●...
Page 244 5-5. Using the driving support systems WARNING Cautions regarding the assist contents of the system ■ By means of alarms and brake control, the pre-collision system is intended to assist the driver in avoiding collisions through the process of LOOK- JUDGE-ACT.
Page 245 5-5. Using the driving support systems BSM (Blind Spot Monitor) Summary of the Blind Spot Monitor The Blind Spot Monitor is a system that has 2 functions; ● The Blind Spot Monitor function Assists the driver in making the decision when changing lanes ●...
Page 246 ■ When “Blind Spot Monitor System Malfunction Visit Your Dealer” is dis- played on the multi-information display There may be a sensor malfunction or voltage abnormality. Have the vehicle inspected at your Toyota dealer.
Page 247 Do not modify the sensor or surrounding area on the bumper. ● Do not paint the rear bumper any color other than an official Toyota color. ● The Blind Spot Monitor function The Blind Spot Monitor function uses radar sensors to detect vehicles...
Page 248 5-5. Using the driving support systems The Blind Spot Monitor function detection areas The areas that vehicles can be detected in are outlined below. The range of the detection area extends to: Approximately 11.5 ft. (3.5 m) from the side of the vehicle The first 1.6 ft.
Page 249 5-5. Using the driving support systems ■ Conditions under which the Blind Spot Monitor function will not detect a vehicle The Blind Spot Monitor function is not designed to detect the following types of vehicles and/or objects: ● Small motorcycles, bicycles, pedestrians, etc. ●...
Page 250 5-5. Using the driving support systems The Rear Cross Traffic Alert function The Rear Cross Traffic Alert function operates when your vehicle is in reverse. It can detect other vehicles approaching from the right or left rear of the vehicle. It uses radar sensors to alert the driver of the other vehicle’s existence through flashing the BSM outside rear view mirror indicators and sounding a buzzer.
Page 251 5-5. Using the driving support systems The Rear Cross Traffic Alert function detection areas The areas that vehicles can be detected in are outlined below. To give the driver a more consistent time to react, the buzzer can alert for faster vehicles from farther away. Example: Approximate Approaching vehicle...
Page 252 5-5. Using the driving support systems ■ Conditions under which the Rear Cross Traffic Alert function may not function correctly The Rear Cross Traffic Alert function may not detect vehicles correctly in the following conditions: ● During bad weather such as heavy rain, fog, snow, etc. ●...
Page 253 5-6. Driving tips Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a man- ner appropriate to the prevailing weather conditions. Preparation for winter ● Use washer fluid that are appropriate to the prevailing outside tem- peratures.
Page 254 5-6. Driving tips When driving the vehicle Accelerate the vehicle slowly, keep a safe distance between you and the vehicle ahead, and drive at a reduced speed suitable to road con- ditions. When parking the vehicle Park the vehicle and shift the shift position to P without setting the parking brake.
Page 255 NOTICE Repairing or replacing snow tires ■ Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 256 5-6. Driving tips...
Page 257 Interior features 6-1. Using the air 6-3. Using the storage conditioning system features and defogger List of storage features ..272 Automatic air conditioning • Glove box...... 273 system......258 • Console box....273 • Cup holders ....274 Heated steering wheel/ •...
Page 258: System
6-1. Using the air conditioning system and defogger Automatic air conditioning system Air outlets and fan speed are automatically adjusted according to the temperature setting. Air conditioning controls ■ Adjusting the temperature setting To adjust the temperature set- ting, touch and slide your finger up or down on the sensor.
Page 259 6-1. Using the air conditioning system and defogger ■ Fan speed setting Touch (increase) to increase the fan speed and (decrease) to decrease the fan speed. Touch to turn the fan off. ■ Change the airflow mode To change the airflow mode, touch outlets used...
Page 260 6-1. Using the air conditioning system and defogger Using the automatic air conditioning system Touch The dehumidification function begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting. Adjust the temperature setting. Touch The cooling and dehumidification function switches between on and off each time the button is touched.
Page 261 6-1. Using the air conditioning system and defogger ■ Defogging the windshield Defoggers are used to defog the windshield and front side win- dows. Press Set the outside/recirculated air mode button to the outside air mode if the recirculated air mode is used. (It may switch automatically.) To defog the windshield and the side windows early, turn the air flow and temperature up.
Page 262 6-1. Using the air conditioning system and defogger Air outlets ■ Location of air outlets The air outlets and air volume change according selected airflow mode. ■ Adjusting the position of and opening and closing the air out- lets Front Rear ...
Page 263 6-1. Using the air conditioning system and defogger ■ Fogging up of the windows ● The windows will easily fog up when the humidity in the vehicle is high. Turning on will dehumidify the air from the outlets and defog the wind- shield effectively.
Page 264 6-1. Using the air conditioning system and defogger ■ When the outside temperature is low The dehumidification function may not operate even when is pressed. ■ Ventilation and air conditioning odors ● To let fresh air in, set the air conditioning system to the outside air mode. ●...
Page 265 6-1. Using the air conditioning system and defogger ■ Turning ON/OFF the switch operation sound for the air conditioning operation panel The operation sounds, when the switch is touched, can be turned ON/OFF by the following operations. The air conditioning cannot be operated during following operation. Touch for about 3 seconds.
Page 266 6-1. Using the air conditioning system and defogger WARNING To prevent the windshield from fogging up ■ Do not use during cool air operation in extremely humid weather. ● The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, block- ing your vision.
Page 267: Heated Steering Wheel Seat Heaters
6-1. Using the air conditioning system and defogger Heated steering wheel/seat heaters Heated steering wheel and seat heaters heat the side grips of the steering wheel and seats, respectively. WARNING Care should be taken to prevent injury if anyone in the following categories ●...
Page 268 6-1. Using the air conditioning system and defogger ■ Operation condition The heated steering wheel can be used when the power switch is in ON mode. ■ Timer The heated steering wheel will automatically turn off after about 30 minutes. Seat heaters ...
Page 269 6-2. Using the interior lights Interior lights list Front interior light (→P. 270) Door courtesy lights 1, 2 Personal lights (→P. 270) Footwell lights Rear interior light (→P. 270) Shift lever lights : When the power switch is in ON mode, the footwell lights will turn on. How- ever, if the instrument panel light control switch is turned to minimum, the footwell lights will turn off.
Page 270: Interior Lights
6-2. Using the interior lights Interior lights  Front When the switch is pressed to the fully pushed in posi- tion, lights becomes linked to the doors The light will turn on and off due to the opening and closing of a door.
Page 271 6-2. Using the interior lights Illuminated entry system ■ The lights automatically turn on/off according to power switch mode, the pres- ence of the electronic key, whether the doors are locked/unlocked, and whether the doors are opened/closed. To prevent 12-volt battery discharge ■...
Page 272: Using The Storage Features List Of Storage Features
6-3. Using the storage features List of storage features Auxiliary boxes (→P. 276) Console box (→P. 273) Glove box (→P. 273) Cup holders (→P. 274) Bottle holders (→P. 276) WARNING Do not leave glasses, lighters or spray cans in the storage spaces, as this ●...
Page 273: Glove Box
6-3. Using the storage features Glove box Open (press the button) Lock with the mechanical key Unlock with the mechanical key Console box  Front Slide the armrest to the rear most position. Lift the lid while pulling up the lever to release the lock.
Page 274: Cup Holders
6-3. Using the storage features  Rear Lift the lid while pushing the but- ton to release the lock. Cup holders  Front Push in the lid.  Rear Push in and release the cup holder.
Page 275 6-3. Using the storage features When stowing bottles (front cup holder) ■ When bottles are stowed in the cup holder of the armrest side, when sliding the armrest, the bottles interfere and may prevent movement of the armrest. WARNING Items unsuitable for the cup holders ■...
Page 276: Bottle Holders
6-3. Using the storage features Bottle holders When storing a bottle, close the cap. ● The bottle may not be stored depending on its size or shape. ● WARNING Do not place anything other than a bottle in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
Page 277: Trunk Features
6-3. Using the storage features Trunk features Grocery bag hooks NOTICE To prevent damage to the hooks, do not apply too much load to the hooks. Warning reflector storage space The warning reflector can be stowed underneath the luggage mat. Stowing the warning reflector ■...
Page 278 6-3. Using the storage features First-aid kit storage belt Loosen the belt Tighten the belt...
Page 279: Sun Visors
6-4. Other interior features Other interior features Sun visors To set the visor in the forward position, flip it down. To set the visor in the side posi- tion, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it backward.
Page 280: Clock
6-4. Other interior features Clock The time can be adjusted through the [settings display] for the multi-information display (→P. 107) ◆ Round to the nearest hour Press of the meter control switches (→P. 108), select and press The minute section of the clock goes to 00. : e.g.1:00 to 1:29 →...
Page 281: Armrest
6-4. Other interior features Armrest Front  Slide the armrest. Rear  NOTICE To prevent damage to the armrest, do not apply too much load on the arm- rest. Coat hooks The coat hooks are provided with the rear assist grips.
Page 282: Assist Grips
6-4. Other interior features WARNING Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury. NOTICE To prevent damage to the coat hook, do not put a heavy load on the coat hook.
Page 283: Power Outlet
6-4. Other interior features Power outlet Please use a power supply for electronic goods that use less than 12 VDC/10 A (power consumption of 120 W). Push the cover of the console box to open. Open the lid. The power outlet can be used when the power switch is in ACCESSORY or ON mode.
Page 284: Wireless Charger
6-4. Other interior features Wireless charger A portable device can be charged by just placing Qi standard wireless charge compatible portable devices according to the Wireless Power Consortium, such as smart phones and mobile batteries, etc., on the charge area. This function cannot be used with portable devices that are larger than the charging area.
Page 285 6-4. Other interior features ■ Using the wireless charger Open the console box. (→P. 273). Press the power supply switch of the wireless charger. Switches on and off with each press of the power supply switch. When turned on, the operation indicator light (green) comes on.
Page 286 Handle the error based on the following table. Operation indicator Suspected causes Handling method light Flashing repeatedly Vehicle to charger com- Contact your Toyota once every second munication failure. dealer. (Orange) Remove foreign A foreign substance is substance...
Page 287 6-4. Other interior features ■ The wireless charger can be operated when The power switch is in ACCESSORY or ON mode. ■ Usable portable devices Qi standard wireless charge standard can be used on compatible devices. However, not all Qi standard devices and compatibility are guaranteed. Starting with mobile phones and smart phones, it is aimed for low power elec- trically supplied portable devices of no more than 5 W.
Page 288 6-4. Other interior features ■ Certification for the wireless charger FCC Note: This equipment has been tested and found to comply with Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Page 289 6-4. Other interior features...
Page 290 6-4. Other interior features WARNING Caution while driving ■ When charging a portable device, for safety reasons, the driver should not ● operate the main part of the portable device while driving. Make sure to close the console box lid while driving. When sudden brak- ●...
Page 291 In addition, excluding the above-mentioned, when the charger does not per- form normally or the operation display lamp is flashing continuously, it is considered that the wireless charger is malfunctioning. Contact your Toyota dealer. To prevent failure or damage to data ■...
Page 292: Garage Door Opener
6-4. Other interior features Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, security systems, and other devices.  Programming the HomeLink  The HomeLink wireless control system in your vehicle has 3 buttons which can be programmed to operate 3 different devices.
Page 293 6-4. Other interior features  ■ Programming HomeLink  Press and release the HomeLink button you want to program  and check that the HomeLink indicator light flashes (orange). Perform within 60 seconds of , or the indicator light will stop flashing and programming will not be able to be completed.
Page 294 6-4. Other interior features  Test the HomeLink operation by pressing the newly pro- grammed button and observing the indicator light: ● Device with fixed code: If the indicator light is solid/continuous, programming has been completed and your garage door or ...
Page 295 6-4. Other interior features Press and hold the desired  HomeLink button (inside the vehicle) for 2 seconds and release it. Repeat this sequence (press/hold/ release) up to 3 times to complete programming. If the garage door opener motor  operates when the HomeLink button is pressed, the garage door opener motor recognizes...
Page 296 6-4. Other interior features  ■ Reprogramming a single HomeLink button When the following procedure is performed, buttons which already have devices registered to them can be overwritten:  With one hand, press and hold the desired HomeLink button.  When the HomeLink indicator starts flashing (orange), continue ...
Page 297 6-4. Other interior features  Erasing the entire HomeLink memory (all three codes) Press and hold the 2 outside but- tons for 10 seconds until the  HomeLink indicator light changes from continuously lit (orange) rapidly flashing (green). If you sell your vehicle, be sure to erase the programs stored in the ...
Page 298 6-4. Other interior features WARNING When programming a garage door or other remote control devices ■ The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm. Conforming to federal safety standards ■...
Page 299: Safety Connect
Telematics Subscription Service Agreement and its Terms and Conditions, as in effect and amended from time to time, a current copy of which is available at Toyota.com. All use of the Safety Connect service is subject to such then-applicable Terms and Conditions.
Page 300 Safety Connect. ● Safety Connect is available beginning Fall 2009 on select Toyota models. Contact with the Safety Connect response center is dependent upon the telematics device being in operative condition, cellular connection availabil- ity, and GPS satellite signal reception, which can limit the ability to reach the response center or receive emergency service support.
Page 301 ● Green indicator light flashing = Safety Connect call in process ● Red indicator light (except at vehicle start-up) = System malfunction (contact your Toyota dealer) ● No indicator light (off) = Safety Connect service not active Safety Connect services ■...
Page 302 In addition to assisting law enforcement with recovery of a stolen vehicle, Safety-Connect-equipped vehicle location data may, under certain circumstances, be shared with third parties to locate your vehicle. Further information is available at Toyota.com. ■ Emergency Assistance Button (“SOS”) In the event of an emergency on the road, push the “SOS”...
Page 303 6-4. Other interior features Safety information for Safety Connect Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals.
Page 304 6-4. Other interior features...
Page 305 Maintenance and care 7-1. Maintenance and care Cleaning and protecting the vehicle exterior..306 Cleaning and protecting the vehicle interior... 310 7-2. Maintenance Maintenance requirements ....313 General maintenance..315 7-3. Do-it-yourself maintenance Do-it-yourself service precautions ..... 318 Hood ......... 320 Positioning a floor jack ..
Page 306: The Vehicle Exterior
7-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition: ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 307 • Do not use any metallic objects to remove condensation build up. ● When the water-repellent performance has become insufficient, the coating can be repaired. Contact your Toyota dealer. ■ Restoration work for rain clearing effect of the rain clearing mirror The rain clearing effect on the mirror surface will gradually recover after expo- sure to sunlight (→P.
Page 308 Precaution regarding the rear bumper with Blind Spot Monitor ■ If the paint of the rear bumper is chipped or scratched, the system may mal- function. If this occurs, consult your Toyota dealer. NOTICE To prevent paint deterioration and corrosion on the body and compo- ■...
Page 309 7-1. Maintenance and care NOTICE Cleaning the exterior lights ■ Wash carefully. Do not use organic substances or scrub with a hard brush. ● This may damage the surfaces of the lights. Do not apply wax to the surfaces of the lights. ●...
Page 310: Cleaning And Protecting The Vehicle Interior
7-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: Protecting the vehicle interior ● Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water.
Page 311 7-1. Maintenance and care Caring for leather areas ■ Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. Shampooing the carpets ■ There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
Page 312 7-1. Maintenance and care NOTICE Cleaning detergents ■ Do not use the following types of detergent, as they may discolor the vehi- ● cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye, and bleach •...
Page 313: Maintenance Requirements
Toyota recommends the following main- tenance: General maintenance General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer. Scheduled maintenance Scheduled maintenance should be performed at specified intervals according to the maintenance schedule.
Page 314 Repair and replacement ■ It is recommended that genuine Toyota parts be used for repairs to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 315: General Maintenance
“Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement/Sched- uled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Motor compartment...
Page 316: Maintenance
7-2. Maintenance Vehicle interior Items Check points • The accelerator pedal should Accelerator pedal move smoothly (without uneven pedal effort or catching). • When parked on a slope and the Transmission “Park” mechanism shift position is in P, is the vehicle securely stopped? •...
Page 317 7-2. Maintenance Items Check points • Do seat belts operate smoothly? Seat belts • The seat belts should not be dam- aged. • Do the seat controls operate prop- Seats erly? • Does the steering wheel rotate smoothly? • Does the steering wheel have the Steering wheel correct amount of free play? •...
Page 318: Do-It-Yourself Service Precautions
Brake fluid level • Rag or paper towel (→P. 326) • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol-based non-silicate, non- amine, non-nitrite and non-borate coolant with long- Inverter coolant life hybrid organic acid technology.
Page 319 7-3. Do-it-yourself maintenance WARNING The motor compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions. When working on the motor compartment ■ Be careful not to touch the high-voltage parts or hydrogen-related parts. ●...
Page 320: Hood
7-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood lock release lever. The hood will pop up slightly. Pull up the auxiliary catch lever and lift the hood. WARNING Pre-driving check ■...
Page 321: Positioning A Floor Jack
7-3. Do-it-yourself maintenance Positioning a floor jack When using a floor jack, follow the instructions in the manual provided with the jack and perform the operation safely. When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury.
Page 322 7-3. Do-it-yourself maintenance WARNING When raising your vehicle ■ Make sure to observe the following precautions to reduce the possibility of death or serious injury: Make sure to set the floor jack properly at the jack point. ● Raising the vehicle with an improperly positioned floor jack will damage the vehicle and may cause the vehicle to fall off the floor jack.
Page 323: Motor Compartment
7-3. Do-it-yourself maintenance Motor compartment Washer fluid tank (→P. 327) Inverter coolant radiator (→P. 325) Brake fluid reservoir (→P. 326) Condenser (→P. 325) Inverter coolant reservoir Electric cooling fans (→P. 324) Fuel cell stack coolant reser- voir (→P. 324) Fuse boxes (→P.
Page 324 “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water. (Minimum temperature: -31°F [-35°C]) For more details about inverter coolant, contact your Toyota dealer.
Page 325 ■ Visually check the radiators, hoses, inverter coolant reservoir cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system. WARNING When the fuel cell system is hot ■...
Page 326: Brake Fluid
7-3. Do-it-yourself maintenance Brake fluid Checking fluid level ■ The brake fluid level should be between the “MAX” and “MIN” lines on the tank. “MAX” “MIN” Adding fluid ■ Make sure to check the fluid type and prepare the necessary item. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Item...
Page 327 7-3. Do-it-yourself maintenance Washer fluid If none of the washer do not work or the warning message appears on the multi-information display, the washer tank may be empty. Add washer fluid. (→P. 376) WARNING When adding washer fluid ■ Do not add washer fluid when the fuel cell system is hot or operating, as washer fluid contains alcohol and may catch fire if spilled on the fuel cell system, etc.
Page 328: Volt Battery
7-3. Do-it-yourself maintenance 12-volt battery Location The 12-volt battery is located in the right-hand side of the trunk. Removing the 12-volt battery cover Remove the 12-volt battery cover. Exterior Make sure that the 12-volt battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.
Page 329 When the 12-volt battery is reconnected, start the fuel cell system, depress the brake pedal, and confirm that it is possible to shift into each shift posi- tion. If the system will not start even after multiple attempts at all methods above, contact your Toyota dealer.
Page 330 When replacing the 12-volt battery ■ Use a 12-volt battery designed for this vehicle. Failure to do so may cause gas (hydrogen) to enter the passenger compartment, causing a fire or explosion. For replacement of the 12-volt battery, contact your Toyota dealer.
Page 331 7-3. Do-it-yourself maintenance NOTICE When recharging the 12-volt battery ■ Never recharge the 12-volt battery while the fuel cell system is operating. Also, be sure all accessories are turned off.
Page 332: Tires
Replace the tires if the treadwear indicators are showing on a tire. Tire rotation Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recommends that tire rotation is carried out at the same interval as tire inspection. Front...
Page 333 ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. Have tire pressure warning valves and transmitter ID codes registered by your Toyota dealer. (→P. 333) ◆ Registering ID codes The tire pressure warning valve and transmitter is equipped with a unique ID code.
Page 334 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. ■ Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not reg- istered, the tire pressure warning system will not work properly.
Page 335 7-3. Do-it-yourself maintenance ■ Tire types ● Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 336 ● In the following cases, the tire pressure warning system may not operate properly. • If non-genuine Toyota wheels are used. • A tire has been replaced with a tire that is not an OE (Original Equip- ment) tire. • A tire has been replaced with a tire that is not of the specified size.
Page 337 Do not mix tires of different makes, models or tread patterns. ● Also, do not mix tires of remarkably different treadwear. Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply ●...
Page 338 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. After use of liquid sealant, make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 339: Replacing The Tire
Improper placement may damage your vehicle or cause injury. If necessary tire replacement seems difficult to perform, contact your Toyota dealer. Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake.
Page 340 7-3. Do-it-yourself maintenance WARNING Using the tire jack ■ Observe the following precautions. Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury. Do not use the tire jack for any purpose other than replacing tires or ●...
Page 341 7-3. Do-it-yourself maintenance Replacing a tire Chock the tires. : Chock can be purchased at your Toyota dealer. Tire position Wheel chock positions Left-hand side Behind the rear right-hand side tire Front Right-hand side Behind the rear left-hand side tire...
Page 342 7-3. Do-it-yourself maintenance Check the jack point. The mark ( ) displaying the jack set position is attached to the under side of the side mud guard. mark( mark( Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point.
Page 343 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • When installing the wheel nuts, be sure to install the wheel nuts with the tapered ends facing inward.
Page 344 7-3. Do-it-yourself maintenance Install the tire and loosely Disc wheel tighten each wheel nut by hand by approximately the same amount. Turn the wheel nuts until the washers come into contact with Washer the disc wheel. Lower the vehicle. Firmly tighten each wheel nut two or three times in the order shown in the illustration.
Page 345 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
Page 346: Tire Inflation Pressure
7-3. Do-it-yourself maintenance Tire inflation pressure Tire inflation pressure The recommended cold tire infla- tion pressure and tire size are dis- played on the tire and loading information label. (→P. 421)
Page 347 Driving with incorrect tire inflation pressure may result in the following: ● Reduced fuel economy ● Reduced driving comfort and poor handling ● Reduced tire life due to wear ● Reduced safety ● Damage to the drivetrain If a tire needs frequent inflating, have it checked by your Toyota dealer.
Page 348 7-3. Do-it-yourself maintenance Instructions for checking tire inflation pressure ■ When checking tire inflation pressure, observe the following: Check only when the tires are cold. ● If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
Page 349: Wheels
● Used wheels ● Bent wheels that have been straightened Aluminum wheel precautions ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
Page 350 Because tire repair or replacement may affect the tire pressure warn- ● ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 351: Air Conditioning Filter
7-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method Turn the power switch off. Open the glove box. Slide off the damper. Push the surface on the left side of the glove box inward, undo the upper left claw, then push the surface on the right...
Page 352 7-3. Do-it-yourself maintenance Remove the filter cover. Remove the air conditioning fil- ter and replace it with a new one. The “↑UP” marks shown on the fil- ter should be pointing up. Checking interval ■ Inspect and replace the air conditioning filter according to the maintenance schedule.
Page 353: Electronic Key Battery
7-3. Do-it-yourself maintenance Electronic key battery Replace the battery with a new one if it is depleted. You will need the following items: ● Flathead screwdriver ● Small flathead screwdriver ● Lithium battery CR2032 Replacing the battery Take out the mechanical key. (→P.
Page 354 7-3. Do-it-yourself maintenance Use a CR2032 lithium battery ■ Batteries can be purchased at your Toyota dealer, local electrical appliance ● shops or camera stores. Replace only with the same or equivalent type recommended by the manu- ● facturer. Dispose of used batteries according to local laws.
Page 355: Checking And Replacing Fuses
7-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as nec- essary. Turn the power switch off. Open the fuse box cover. Motor compartment ...
Page 356 7-3. Do-it-yourself maintenance Check if the fuse is blown. Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rat- ing. The amperage rating can be found on the fuse box lid.  Type A ...
Page 357 If the lights do not turn on even after the fuse has been replaced, a bulb may ● need replacement. (→P. 358) If the replaced fuse blows again, have the vehicle inspected by your Toyota ● dealer. If there is an overload in a circuit ■...
Page 358: Light Bulbs
7-3. Do-it-yourself maintenance Light bulbs If any lights burn out, have it replaced by your Toyota dealer: LED light bulbs ■ The following lights consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.
Page 359: When Trouble Arises
When trouble arises 8-1. Essential information Emergency flashers ..360 If your vehicle has to be stopped in an emergency ...... 361 8-2. Steps to take in an emergency If your vehicle needs to be towed ......362 If you think something is wrong ......
Page 360: Emergency Flashers
8-1. Essential information Emergency flashers The emergency flashers are used to warn other drivers when the vehicle has to be stopped in the road due to a breakdown, etc. Press the switch. All the turn signal lights will flash. To turn them off, press the switch once again.
Page 361: Be Stopped In An Emergency
8-1. Essential information If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the follow- ing procedure: Steadily step on the brake pedal with both feet and firmly depress it. Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle.
Page 362: If Your Vehicle Needs To Be Towed
In the following situations, it is not possible to be towed by another vehicle using cables or chains, as the front wheels may be locked due to the parking lock. Contact your Toyota dealer or commercial towing service. ● There is a malfunction in the shift control system. (→P. 378) ●...
Page 363 Situations when it is necessary to contact dealers before towing The following may indicate a problem with your transmission. Contact your Toyota dealer or commercial towing service before towing. ● The fuel cell system warning message shows on the multi-informa- tion display and the vehicle does not move.
Page 364 8-2. Steps to take in an emergency Using a flatbed truck If your vehicle is transported by a flatbed truck, it should be tied down at the locations shown in the illustration. Front If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°.
Page 365 8-2. Steps to take in an emergency Emergency towing procedure Take out the towing eyelet. (→P. 339,382) Remove the eyelet cover using a flathead screwdriver. To protect the bodywork, place a rag between the screwdriver and the vehicle body as shown in the illustration. Front Rear ...
Page 366 8-2. Steps to take in an emergency While towing ■ If the fuel cell system is off, the power assist for the brakes and steering will not function, making steering and braking more difficult. Wheel nut wrench ■ Wheel nut wrench is installed in trunk. (→P. 339, 382) WARNING Observe the following precautions.
Page 367 8-2. Steps to take in an emergency NOTICE To prevent damage to the vehicle when towing using a wheel-lift type ■ truck When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.
Page 368: If You Think Something Is Wrong
8-2. Steps to take in an emergency If you think something is wrong If you notice any of the following symptoms, your vehicle proba- bly needs adjustment or repair. Contact your Toyota dealer as soon as possible. Visible symptoms ● Fluid leaks under the vehicle.
Page 369: On Or A Warning Buzzer Sounds
• The brake fluid level is low; or • The brake system is malfunctioning → Immediately stop the vehicle in a safe place and con- tact your Toyota dealer. Continuing to drive the vehi- cle may be dangerous. Charging system warning light Indicates a malfunction in the vehicle’s charging system...
Page 370 Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system → Have the vehicle inspected by your Toyota dealer immediately. ABS warning light Indicates a malfunction in: •...
Page 371 8-2. Steps to take in an emergency Warning light Warning light/Details/Actions Parking brake warning light (warning buzzer) Parking brake has not been fully released → Operate the parking brake once again. If the light turns off after the parking brake is fully released, the system is operating normally.
Page 372 8-2. Steps to take in an emergency Warning light Warning light/Details/Actions Brake Override System/Drive-Start Control warning light Indicates that: • The Brake Override System is operating; • The Brake Override System is malfunctioning (with warning buzzer); • The Drive-Start Control is operating (with warning buzzer);...
Page 373 If the warning light does not go out even after several minutes, have the vehicle inspected by your Toyota dealer immediately.  The tire pressure warning light is blinking for 1 minute, and then comes Malfunction in the tire pressure warning system.
Page 374 If both the ABS and the brake system warning lights remain on ■ Stop your vehicle in a safe place immediately and contact your Toyota dealer. The vehicle will become extremely unstable during braking, and the ABS system may fail, which could cause an accident resulting in death or serious injury.
Page 375 8-2. Steps to take in an emergency WARNING Maintenance of the tires ■ Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 376: If A Warning Message Is Displayed
Messages and warnings The warning lights and warning buzzers operate as follows depending on the content of the message. If a message indicates the need for inspection by a dealer, have the vehicle inspected by your Toyota dealer immediately. System...
Page 377 If “Maintenance Required for Hybrid Battery Cooling Parts at Your Dealer” is displayed The filter may be clogged, or the air intake vent or duct may be blocked. Have the vehicle inspected by your Toyota dealer. ■ If “Shift to P Before Exiting Vehicle” is displayed Message is displayed when the driver’s door is opened without turning the...
Page 378 ■ If “Ion Filter Maintenance Required Visit Your Dealer” is displayed Ion filter replacement is necessary. Contact your Toyota dealer. ■ If “Shift System Malfunction Stop Your Vehicle in a Safe Place then See Owner's Manual”...
Page 379 When parking, choose a flat surface and be sure to engage the parking brake. Have the vehicle inspected by your Toyota dealer immediately. ■ If “Shift System Malfunction See Owner’s Manual” is displayed If left as is, the system may not operate properly and an unexpected hazard or damage may occur.
Page 380 8-2. Steps to take in an emergency ■ If “Shifting to [D] or [R] Position Unavailable Try to Shift after FC System has Started” is displayed When the power switch is in ON mode (“READY” indicator switched off), a warning message is displayed when trying to shift the shift position to R or D, or shift to Br mode.
Page 381 After temporarily repairing the tire with the repair kit, have the tire repaired or replaced by your Toyota dealer. WARNING If you have a flat tire ■...
Page 382 8-2. Steps to take in an emergency Location of the emergency tire puncture repair kit, tools and jack Wheel nut wrench Jack handle Towing eyelet Jack Emergency tire puncture repair kit : Use of the jack (→P. 341)
Page 383 8-2. Steps to take in an emergency Emergency tire puncture repair kit components Hose Compressor switch Air release cap Power plug Air pressure gauge Stickers...
Page 384 8-2. Steps to take in an emergency Taking out the emergency tire puncture repair kit Remove the luggage mat. Remove the jack handle. Take out the emergency tire puncture repair kit. Before performing emergency repair Check the degree of the tire damage. A tire should only be repaired with emergency tire...
Page 385 8-2. Steps to take in an emergency Emergency repair method Take out the repair kit from the plastic bag. Remove the valve cap from the valve of the punctured tire. Remove the air release cap from the hose. You will use the air release cap again.
Page 386 8-2. Steps to take in an emergency Remove the rubber stopper from the compressor. Connect the power plug to the power outlet socket. (→P. 283) Connect the bottle to the com- pressor. Make sure that the bottle is securely connected.
Page 387 8-2. Steps to take in an emergency Attach the 2 stickers as shown. Remove any dirt and moisture from the wheel before attaching the sticker. Check the specified tire inflation pressure. Tire inflation pressure is specified on the label as shown. (→P. 421) Start the fuel cell system.
Page 388 10 minutes (40 minutes at low temperature) with the switch on, the tire is too damaged to be repaired. Turn the compressor switch off and contact your Toyota dealer. • If the tire inflation pressure exceeds the specified air pressure, let...
Page 389 8-2. Steps to take in an emergency With the compressor switch off, disconnect the hose from the valve on the tire and then pull out the power plug from the power outlet socket. Some sealant may leak when the hose is removed. Install the valve cap onto the valve of the emergency repaired tire.
Page 390 Store the bottle in the trunk while it is connected to the compressor. Taking precautions to avoid sudden braking, sudden acceleration and sharp turns, drive carefully at under 50 mph (80 km/h) to the nearest Toyota dealer tire repair or replacement.
Page 391 The sealant stored in the emergency tire puncture repair kit can be used only once to temporarily repair a single tire. If the sealant has been used and needs to be replaced, purchase a new bottle at your Toyota dealer. The compressor is reusable.
Page 392 8-2. Steps to take in an emergency If the tire is inflated to more than the specified air pressure ■ Disconnect the hose from the valve. Install the air release cap to the end of the hose and push the protrusion on the air release cap into the tire valve to let some air out.
Page 393 8-2. Steps to take in an emergency WARNING Precautions for use of the sealant ■ Ingesting the sealant is hazardous to your health. If you ingest sealant, ● consume as much water as possible, and then immediately consult a doctor. If sealant gets in eyes or adheres to skin, immediately wash it off with ●...
Page 394 8-2. Steps to take in an emergency WARNING riving to spread the liquid sealant evenly ■ Observe the following precautions to reduce the risk of accidents. Failure to do so may result in a loss of vehicle control and cause death or serious injury.
Page 395 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer as soon as possible. After use of liquid sealant, make sure to replace the tire pressure warning valve and trans-...
Page 396: If The Fuel Cell System Will Not Start
8-2. Steps to take in an emergency If the fuel cell system will not start Reasons for the fuel cell system not starting vary depending on the situation. Check the following and perform the appropriate procedure: The fuel cell system will not start even though the correct start- ing procedure is being followed.
Page 397 ● The 12-volt battery may be discharged. (→P. 401) ● One or both of the 12-volt battery terminals may be disconnected. Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. Emergency start function...
Page 398: If The Electronic Key Does Not Operate Properly
8-2. Steps to take in an emergency If the electronic key does not operate properly If communication between the electronic key and vehicle is interrupted (→P. 134) or the electronic key cannot be used because the battery is depleted, the smart key system and wire- less remote control cannot be used.
Page 399 : These settings must be customized at your Toyota dealer. (→P. 437) Starting the fuel cell system Depress the brake pedal. Touch the power switch with the Toyota emblem side of the elec- tronic key facing away from the switch. When electronic detected, a buzzer sounds and the power switch will turn to ON mode.
Page 400 8-2. Steps to take in an emergency Stopping the fuel cell system ■ Shift the shift position to P and press the power switch as you normally do when stopping the fuel cell system. Replacing the key battery ■ As the above procedure is a temporary measure, it is recommended that the electronic key battery be replaced immediately when the battery is depleted.
Page 401: If The 12-Volt Battery Is Discharged
The following procedures may be used to start the fuel cell sys- tem if the 12-volt battery is discharged. You can also call your Toyota dealer or a qualified repair shop. If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt battery, you can jump start your vehicle by following the steps below.
Page 402 ON mode. Make sure the “READY” indicator comes on. If the indicator does not come on, contact your Toyota dealer. Once the fuel cell system has started, remove the jumper cables in...
Page 403 Once the fuel cell system starts, have the vehicle inspected at your Toyota dealer as soon as possible. ■ Starting the fuel cell system when the 12-volt battery is discharged The fuel cell system cannot be started by push-starting.
Page 404 • If the 20 hour rate capacity is low, even if the time period where the vehicle is not used is a short time, the 12-volt battery may discharge and fuel cell system may not be able to start. For details, consult your Toyota dealer. WARNING Avoiding 12-volt battery fires or explosions ■...
Page 405 WARNING After recharging the 12-volt battery ■ Have the 12-volt battery inspected at your Toyota dealer as soon as possi- ble. If the 12-volt battery is deteriorating, continued use may cause the 12-volt battery to emit a malodorous gas, which may be detrimental to the health of passengers.
Page 406: If Your Vehicle Overheats
8-2. Steps to take in an emergency If your vehicle overheats The following may indicate that your vehicle is overheating. ● The high coolant temperature warning light (→P. 369) comes on or flashes, or a loss of fuel cell system power is experienced. (For example, the vehicle speed does not increase.) ●...
Page 407 If the fuel cell stack coolant is low, imme- diately contact your Toyota dealer. Correction procedures If the high coolant temperature warning light comes on or ■...
Page 408 If the amount of fuel cell stack coolant is low: Immediately contact your Toyota dealer. If the amount of fuel cell stack coolant is not low: Have the vehicle inspected at the nearest Toyota dealer. Even if the fuel cell stack cool- ant is low, do not refill it.
Page 409 (radiator) for any leaks. Inverter coolant radiator Electric cooling fans If a large amount of coolant leaks, immediately contact your Toyota dealer. The inverter coolant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir.
Page 410 (The fans may not operate in freezing temperatures.) If the fans are not operating: Stop the fuel cell system immediately and contact your Toyota dealer. If the fans are operating: Have the vehicle inspected at the nearest Toyota dealer.
Page 411 ● etc.). Do not use any coolant additive with inverter coolant. ● For replacement of the fuel cell stack coolant, contact your Toyota dealer. ● Do not use water or any other coolant when refilling the fuel cell stack ●...
Page 412: If The Vehicle Becomes Stuck
8-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: Set the parking brake and stop the fuel cell system. Remove the mud, snow or sand from around the front wheels.
Page 413 8-2. Steps to take in an emergency NOTICE To avoid damaging the transmission and other components ■ Avoid spinning the front wheels and depressing the accelerator pedal ● more than necessary. If the vehicle remains stuck even after these procedures are performed, ●...
Page 414 8-2. Steps to take in an emergency...
Page 415 Vehicle specifications 9-1. Specifications Maintenance data (fuel, fluid level, etc.) ..416 Tire information ....422 9-2. Customization Customizable features ..434 9-3. Items to initialize Items to initialize ....442...
Page 416 9-1. Specifications Maintenance data (fuel, fluid level, etc.) Dimensions and weight Overall length 192.5 in. (4890 mm) Overall width 71.5 in. (1815 mm) Overall height 60.5 in. (1535 mm) Wheelbase 109.5 in. (2780 mm) Front 60.5 in. (1535 mm) Tread Rear 61.0 in.
Page 417 The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 418 9-1. Specifications Fuel Fuel type Compressed hydrogen gas Nominal working 10150 psi (70 MPa, 714 kgf/cm , 700 bar) pressure Hydrogen tanks’ fuel 32.3 gal. (122.4 L, 26.9 Imp.gal.) capacity (Approximately 11.0 lb. [5 kg] (Reference) *: This is the maximum possible fill amount. The actual fuel amount achieved at hydrogen stations may be lower due to station capacity or station set- tings.
Page 419: Cooling System
Do not use plain water alone. *: The fluid capacity is a reference quantity. If replacement is necessary, contact your Toyota dealer. NOTICE The fuel cell stack coolant is exclusive for fuel cell stack usage. Damage may occur when water or any other type of coolant is used, so never use any other fluid.
Page 420: Electrical System
: The fluid capacity is a reference quantity. If replacement is necessary, contact your Toyota dealer. NOTICE Transmission fluid type ■ Using transmission fluid other than “Toyota Genuine ATF WS” may ulti- mately damage the transmission of your vehicle. Brakes Pedal clearance 2.95 in. (75 mm) Min.
Page 421 9-1. Specifications Steering Free play Less than 1.2 in. (30 mm) Tires and wheels Tire size P215/55R17 93V  Front Tire inflation pressure 36 psi (250 kPa, 2.5 kgf/cm or bar) (Recommended cold tire  Rear inflation pressure) 36 psi (250 kPa, 2.5 kgf/cm or bar) 17 ×...
Page 422: Tire Information
9-1. Specifications Tire information Typical tire symbols Tire size (→P. 424) DOT and Tire Identification Number (TIN)(→P. 423) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators(→P. 332) Tire ply composition and materials Plies are layers of rubber-coated parallel cords.
Page 423 9-1. Specifications Typical DOT and Tire Identification Number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer’s identifica- tion mark Tire size code Manufacturer’s optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.
Page 424 9-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits)
Page 425 9-1. Specifications Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer...
Page 426 U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Require- ments in addition to these grades.
Page 427 9-1. Specifications ■ Temperature A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissi- pate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 428 9-1. Specifications Glossary of tire terminology Tire related term Meaning Tire pressure when the vehicle has been Cold tire inflation pres- parked for three hours or more, or has not sure been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which Maximum...
Page 429 9-1. Specifications Tire related term Meaning The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they Production options replace, not previously considered in curb weight weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty 12-volt battery, and special trim A metal support for a tire or a tire and tube...
Page 430 9-1. Specifications Tire related term Meaning A pneumatic tire in which the ply cords that extend to the beads are laid at alternate Bias ply tire angles substantially less than 90 degrees to the centerline of the tread The tire structure, except tread and sidewall Carcass rubber which, when inflated, bears the load The breaking away of pieces of the tread or...
Page 431 9-1. Specifications Tire related term Meaning A tire designated by its manufacturer as pri- Light truck (LT) tire marily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry Load rating for a given inflation pressure The load rating for a tire at the maximum per- Maximum load rating...
Page 432 9-1. Specifications Tire related term Meaning The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- Section width vations due to labeling, decoration, or protec- tive bands That portion of a tire between the tread and Sidewall bead The parting of the rubber compound from the...
Page 433 9-1. Specifications Designated seating Occupant distribution Vehicle normal load, capacity, Number of in a normally loaded Number of occupants occupants vehicle 2 through 4 2 in front 2 in front, 1 in second 5 through 10 seat 2 in front, 1 in second 11 through 15 seat, 1 in third seat, 1 in fourth seat...
Page 434: Customization Customizable Features
The settings of these fea- tures can be changed by using the navigation system, the multi- information display, or at your Toyota dealer. Customizing vehicle features When customizing vehicle features, ensure that the vehicle is parked in a safe place with the shift position in P and the parking brake set.
Page 435 Customizable features Some function settings are changed simultaneously with other func- tions being customized. Contact your Toyota dealer for further details. Settings that can be changed by the navigation system Settings that can be changed by the multi-information display...
Page 436 9-2. Customization ■ Smart key system and wireless remote control (→P. 120, 131) Default Customized Function setting setting Operation signal (emergency O — — O flashers) Operation buzzer volume Level 5 O — — O Level 1 to 7 Time elapsed before the automatic door lock function 30 seconds 60 seconds...
Page 437 9-2. Customization ■ Wireless remote control (→P. 120, 126) Default Customized Function setting setting Wireless remote control — — — O Driver’s door unlocked in All doors first step, all Unlocking operation unlocked in O — — O doors first step unlocked in second step One short...
Page 438 9-2. Customization ■ Outside rear view mirrors (→P. 151) Default Customized Function setting setting Linked to Automatic folding/extending locking/ Linked to — — — O operation unlocking of power switch the doors operation Linked mirror function when — — — O reversing ■...
Page 439 9-2. Customization ■ Automatic air conditioning system (→P. 258) Default Customized Function setting setting Reaction when the A/C 01 (Fast) 05 (Slow) — — O — switch is pressed to 05 (Slow) Operation noise when the — — O — A/C switch is pressed Display popup when the A/C —...
Page 440 9-2. Customization ■ Vehicle Proximity Notification System (→P. 84) Default Customized Function setting setting volume Vehicle Proximity Notification Level 1 — — — O Level 2 System sound ■ Intuitive parking assist (→P. 223) Default Customized Function setting setting Detection distance of the Long Short O —...
Page 441 9-2. Customization Vehicle customization ■ When the speed linked door locking function and shift position linked door ● locking function are both on, the door lock operates as follows. • When shifting the shift position to any position other than P, all the doors will be locked.
Page 442: Items To Initialize Items To Initialize
9-3. Items to initialize Items to initialize The following items must be initialized for normal system opera- tion after such cases as the 12-volt battery being reconnected, or maintenance being performed on the vehicle: Item When to initialize Reference Power window When functioning abnormally P.
Page 443: 10 For Owners
For owners Reporting safety defects for U.S. owners......444...
Page 444: Reporting Safety Defects For U.s. Owners
National Highway Traffic Safety Administration (NHTSA) in addi- tion to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800- 331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 445: Index
Index What to do if... (Troubleshooting) ....446 Alphabetical index ..... 449 For information regarding the equipment listed below, refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”. • Navigation system • Rear view monitor system • Audio system...
Page 446 Toyota dealer. (→P. 117) ● If you lose your electronic keys, the risk of vehicle theft increases signifi- cantly. Contact your Toyota dealer immediately. (→P. 119) The doors cannot be locked or unlocked ● Is the key battery weak or depleted? (→P. 353) ●...
Page 447 What to do if... (Troubleshooting) If you think something is wrong The fuel cell system does not start ● Did you press the power switch while firmly depressing the brake pedal? (→P. 172) ● Is the shift position in P? (→P. 180) ●...
Page 448 What to do if... (Troubleshooting) A warning buzzer sounds during driving ● The seat belt reminder light is flashing Are the driver and the front passenger wearing the seat belts? (→P. 371) ● The brake system warning light is on Is the parking brake released? (→P.
Page 449: Alphabetical Index
Alphabetical index Alphabetical index Alarm .......... 74 Anchor brackets ......69 A/C ..........258 Antennas Air conditioning filter ..... 351 (smart key system) ....131 Automatic air conditioning Anti-lock Brake System system ........ 258 (ABS) ........232 Function........ 232 (Anti-lock Brake System)..232 Warning light......
Page 450 Alphabetical index Back-up lights Care ........306, 310 Replacing light bulb ....358 Aluminum wheels ....307 Battery (12-volt battery) ..328 Exterior ......... 306 Battery checking ....328 Interior ........310 If the 12-volt battery is Seat belts......311 discharged......
Page 451 Alphabetical index Child-protectors....... 123 Display Cleaning ......306, 310 Drive information ....108 Aluminum wheels....307 Dynamic radar cruise Exterior ......... 306 control ........ 203 Interior........310 Energy monitor ..... 108 Seat belts......311 Clock......... 280 (Lane Departure Alert) ..216 Coat hooks .......
Page 452 Alphabetical index Driving Emergency, in case of Break-in tips......160 If a warning buzzer sounds... 369 Correct driving posture ... 28 If a warning light turns on ..369 Driving advice ......94 If a warning message is Fuel cell vehicle driving displayed ......
Page 453 Alphabetical index Fuel cell system Characteristics......78 Flat tire........381 Cold temperatures ....175 Floor mats ........26 Coolant type ......419 Fluid Indicators ......100 Brake ........420 Multi-information display..107 Transmission ......420 Precautions......82 Washer ......... 327 Starting the system....
Page 454 Alphabetical index Opening the fuel door ... 198 Overheating ......406 O switch ....... 173 Power output restriction ..88 Hands-free system Power switch......172 (for cellular phone) Precautions......82 Head restraints ......145 Regenerative braking....81 Headlights ........ 187 Road accident cautions ..
Page 455 Alphabetical index Identification Jack Vehicle ........417 Positioning a floor jack..321 Illuminated entry system ..271 Vehicle-equipped Immobilizer system ....72 jack......339, 382 Indicators ......... 100 Jack handle...... 339, 382 Initialization Jam protection function Ion filter ......... 439 Power window ......
Page 456 Alphabetical index Lane Departure Alert (LDA) ..216 Maintenance LATCH anchors ......67 Do-it-yourself maintenance... 318 LDA (Lane Departure Alert) ..216 General maintenance ... 315 Lever Maintenance data ....416 Auxiliary catch lever....320 Maintenance Hood lock release lever ..320 requirements ......
Page 457 Alphabetical index P position switch..... 180 Navigation system Parking brake......186 Operation......186 Parking brake engaged Odometer........102 warning buzzer/message ... 186 Opener Warning light......371 Fuel door....... 200 Parking lights......187 Hood ........320 Light switch......187 Trunk........126 Replacing light bulbs ....
Page 458 Alphabetical index Radar cruise control (dynamic Safety Connect ......299 radar cruise control) ..... 203 Seat belt reminder light ..371 Radiator ........325 Seat belts ........30 Radio Adjusting the seat belt .... 31 Rear Crossing Traffic Alert..245 Automatic Locking Rear interior lights....
Page 459 Alphabetical index Seats Side mirrors ......151 Adjustment......138 Adjusting and folding .... 151 Adjustment precautions ..139 BSM (Blind Spot Monitor) ..245 Child seats/child restraint Heaters ......... 261 system installation ....56 Side turn signal lights..... 185 Cleaning........ 310 Replacing light bulbs ....
Page 460 Alphabetical index Switches Rear window and outside Audio remote control switches rear view mirror Automatic High Beam defoggers switch ....261 switch ......... 190 Seat heater switches .... 268 Door lock switches....122 “SOS” button......299 Driving position memory Talk switch switches......
Page 461 Alphabetical index Tire pressure warning system TRAC (Traction Control) ..232 Function ........ 333 Traction battery ......83 Installing tire pressure Air intake vent......85 warning valves Charging ......... 81 and transmitters....333 Location ......78, 83 Registering ID codes .... 333 Warning message....
Page 462 Alphabetical index Warning lights ABS ........370 USB port Brake Override System ..372 Brake system......369 Charging system....369 Vanity lights Drive-Start Control....372 Vanity lights ......279 Electric power steering Wattage ........ 421 system........ 370 Vanity mirrors ......279 High coolant temperature Vanity lights ......
Page 463 Alphabetical index Wheels ........349 Replacing......349 Size........421 Window glasses....... 154 Window lock switch ....154 Windows........154 Power windows..... 154 Rear window defogger..261 Windshield wipers ....195 Winter driving tips ....253 Wireless remote control..116 Battery-Saving Function ..133 Locking/Unlocking....
Page 464 HYDROGEN STATION INFORMATION Auxiliary catch lever Trunk opener Fuel door P. 320 P. 126 P. 200 Tire inflation Hood lock release Fuel door opener pressure lever P. 421 P. 320 P. 200 32.3 gal. (122.4 L, 26.9 Imp.gal.) (Approximately 11.0 lb. [5 kg] Hydrogen tanks’...

Toyota Mirai 2017 Owner's Manual

For Safety and Security

1-1. for Safe Use

1-2. Theft Deterrent System

Fuel Cell System

Fuel Cell Vehicle Fuel Cell Vehicle

Instrument Cluster

Instrument Cluster Warning Lights and

Operation of each Component

4-1. Key Information

4-2. Opening, Closing and

4-3. Adjusting the Seats

Adjusting the Steering Wheel and Mirrors

Quick Links

Troubleshooting

Related Manuals for Toyota Mirai 2017

Summary of Contents for Toyota Mirai 2017

Table of Contents