IBM 2193 Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Desktop
  5. Types 2193
  6. Hardware maintenance manual
IBM 2193 Hardware Maintenance Manual

IBM 2193 Hardware Maintenance Manual

Hide thumbs Also See for 2193:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Maintenance and Service Manual, User Manual

Advertisement

Table of Contents
loading

Related Manuals for IBM 2193

Summary of Contents for IBM 2193

  • Page 7 Hardware Maintenance Service for Service Level A For Micro Tower Models Machine Types 2193, 2194 and 6345 For Desktop Models Machine Types 2196, 2197 and 6344...
  • Page 8 IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. References to IBM products, programs, or services do not imply that IBM intends to make them available outside the United States. This publication could include technical inaccuracies or typographical errors.

  • Page 9: Table Of Contents

    Contents Notices................1 Voltage Supply Switch Settings........1 Safety Information............2 Laser Compliance Statement .......... 28 Trademarks..............29 Preface ................30 General Information ............31 Introduction ..............32 Product Overview............32 Hardware Interfaces............36 CMOS Reset..............38 Flash (BIOS) Update Procedure........38 BIOS-contained Model Number and Serial Number ..
  • Page 10 Layout of the System Board of Machine Types 2197 and 6344................131 Jumper Settings............132 Connectors and Functions ........133 Layout of the System Board of Machine Types 2193 and 2196................ 134 Jumper Settings............135 Connectors and Functions ........136 Power Supply Cable Connector Specifications....
  • Page 11 Safety Inspection Guide ..........149 General Guidelines ............150 Parts Catalog..............151 Parts Catalog of machine type 2193, 2194 and 6345 ..152 Assembly 1 : System Unit .......... 152 Assembly 2 : Diskette Drive, Hard Disk Drive ..... 155 Assembly 3 : CD-ROM, Modem Card......

  • Page 13: Notices

    IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only IBM’s product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any of IBM’s intellectual property rights, or other legally protectable rights, may be used instead of the IBM product, program, or service.

  • Page 14: Safety Information

    Safety Information DANGER To avoid a shock hazard, do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. To avoid shock hazard: The power cord must be connected to a properly wired and earthed receptacle.
  • Page 15 Caution: When replacing the battery, use only IBM Part Number 36L9077 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
  • Page 16 DANGER Some CD-ROM drives contain an embedded Class 3A or Class 3B laser diode. Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. ≥...
  • Page 17 PERIGO Para evitar choques elétricos, não conecte ou desconecte nenhum cabo, nem efetue instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. Para evitar choques elétricos: O cabo de alimentação deve ser conectado a um receptáculo corretamente instalado e aterrado. Todos os equipamentos aos quais este produto será...
  • Page 18 Ao substituir a bateria, utilize apenas o Número de Peça IBM 33F8354 ou um tipo de bateria equivalente recomendado pelo fabricante. Se seu sistema possuir um módulo com uma bateria de lítio, substitua-o apenas pelo mesmo tipo de módulo, produzido pelo mesmo fabricante.
  • Page 19 PERIGO Algumas unidades de CD-ROM contém um diodo de laser da Classe 3A ou da Classe 3B. Observe o seguinte. Radiação de laser quando aberto. Não olhe diretamente para o feixe de laser, não olhe diretamente com instrumentos óticos, e evite exposição direta ao raio. ≥...
  • Page 25 DANGER Pour éviter tout risque de choc électrique, ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage. Pour éviter tout risque de choc électrique : Les cordons d'alimentation du présent produit et de tous les appareils qui lui sont connectés doivent être branchés sur des socles de prise de courant correctement câblés et mis à...
  • Page 26 Remplacez la pile usagée par une pile de référence identique exclusivement - voir la référence IBM - ou par une pile équivalente recommandée par le fabricant. Si votre système est doté d'un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
  • Page 27 DANGER Certaines unités de CD-ROM contiennent une diode laser de classe 3A ou 3B. Prenez connaissance des informations suivantes : Rayonnement laser lorsque le carter est ouvert. Évitez de regarder fixement le faisceau ou de l'observer à l'aide d'instruments optiques. Évitez une exposition directe au rayon.
  • Page 28 VORSICHT Aus Sicherheitsgründen bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. Aus Sicherheitsgründen: Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen. Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß geerdetem Schutzkontakt anschließen.
  • Page 29 Eine verbrauchte Batterie nur durch eine Batterie mit der IBM Teilenummer 33F8354 oder durch eine vom Hersteller empfohlene Batterie ersetzen. Wenn Ihr System ein Modul mit einer Lithium-Batterie enthält, ersetzen Sie es immer mit dem selben Modultyp vom selben Hersteller. Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder...
  • Page 30 ≥ 32 Kg ≥ 55 Kg achtung: Beim Anheben der Maschine die vorgeschriebenen Sicherheitsbestimmungen beachten. achtung: An Netz-, Telefon- und Datenleitungen können gefährliche elektrische Spannungen anliegen. Um eine Gefährdung des Benutzers oder Beschädigung des Geräts zu vermeiden, ist der Server auszuschalten. Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen des Servergehäuses zu unterbrechen...
  • Page 31 PERICOLO Per evitare il pericolo di scosse elettriche durante i temporali, non collegare o scollegare cavi, non effettuare l’installazione, la manutenzione o la riconfigurazione di questo prodotto. Per evitare il pericolo di scosse elettriche: collegare il cavo di alimentazione ad una presa elettrica correttamente cablata e munita di terra di sicurezza;...
  • Page 32 ATTENZIONE: Quando si sostituisce la batteria, utilizzare solo una batteria IBM o batterie dello stesso tipo o di tipo equivalente consigliate dal produttore. Se il sistema di cui si dispone è provvisto di un modulo contenente una batteria al litio, sostituire tale batteria solo con un tipo di modulo uguale a quello fornito dal produttore.
  • Page 33 PERICOLO Alcune unità CD-ROM contengono all'interno un diodo laser di Classe 3A o Classe 3B. Prestare attenzione a quanto segue: Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione diretta al fascio. ≥...
  • Page 37 PELIGRO Para evitar una posible descarga eléctrica, no conecte ni desconecte los cables ni lleve a cabo ninguna operación de instalación, de mantenimiento o de reconfiguración de este producto durante una tormenta eléctrica. Para evitar una posible descarga: El cable de alimentación debe conectarse a un receptáculo con una instalación eléctrica correcta y con toma de tierra.
  • Page 38 Al cambiar la batería, utilice únicamente la batería IBM Número de pieza 33F8354 o un tipo de batería equivalente recomendado por el fabricante. Si el sistema tiene un módulo que contiene una batería de litio, sustitúyalo únicamente por el mismo tipo de módulo del mismo fabricante.
  • Page 39 PELIGRO Algunas unidades de CD-ROM tienen incorporado un diodo de láser de Clase 3A o de Clase 3B Tenga en cuenta la siguiente información. Cuando la unidad está abierta se generan emisiones de rayos láser. No dirija la mirada al haz, no lo observe directamente con instrumentos ópticos y evite la exposición directa.

  • Page 40: Laser Compliance Statement

    Laser Compliance Statement The CD/DVD-ROM drive in the computer is a laser product. The CD/DVD-ROM drive’s classification label (sample shown below) is located on the drive. CLASS 1 LASER PRODUCT APPAREIL A LASER CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 The CD/DVD-ROM drive is certified in the U.S.

  • Page 41: Trademarks

    Trademarks The following are trademarks of the IBM Corporation in the United States or other countries or both: Operating System/2 OS/2 Personal System/2 HelpCenter PS/1 PS/2 Intel, Pentium, MMX, EtherExpress, and LANDesk are trademarks or registered trademarks of Intel Corporation.

  • Page 42: Preface

    Level A (SL-A) model of the IBM Personal Computer, worldwide. This manual is intended to be used as a stand-alone document to service machine types 2193, 2194, 2196, 2197, 6344 and 6345. It is divided into the following chapters: Notices contains important safety information and notices required to service this computer.

  • Page 43: General Information

    General Information General Information ............31 Introduction ..............32 Product Overview............32 Hardware Interfaces............36 CMOS Reset..............38 Flash (BIOS) Update Procedure........38 BIOS-contained Model Number and Serial Number ..39 BIOS Setup Utility ............40 Working with the Setup Menus ......... 40 Start Options.............

  • Page 44: Introduction

    Introduction This chapter gives a general overview of the machine types 2193, 2194, 2196, 2197, 6344 and 6345, describes the standard and optional features, and details functional and environmental specifications. Machine types 2196, 2197 and 6344 are desktop models. Machine types 2193, 2194 and 6345 are micro tower models.
  • Page 45 − Intel Pentium III 667 MHz CPU Memory • 512-KB Pipeline Burst Static RAM (PBSRAM). Fixed onboard. • 168-pin synchronous dynamic random access memory (SDRAM), dual inline memory module (DIMM) sockets. − 2 memory sockets. − 16-MB, 32-MB, 64-MB or 128-MB DIMM. −...
  • Page 46 • 512 KB cache buffer in hard disk drive. • Average and minimum 11.1 ms seek time, access time varies for the hard disk drive and the hard disk drive manufacturer. CD-ROM Drive • 5.25-in. high-performance, 40X CD-ROM IDE/AT drive. •...
  • Page 47 • Auto-sensing power input for 100 V ac to 240 V ac. Keyboard • PS/2 104-key rubber dome IBM Keyboard with 1.8-m (5.8-ft) cable. Keyboard is Geography/Model dependent. Mouse • 2 button mouse connected to the mouse port with 1.8-m...

  • Page 48: Hardware Interfaces

    Photo-CD (both single and multi- session) format. Diskette Drive AT diskette interface Video Physical interface is compatible with the IBM Personal System/2 (PS/2) VGA interface. SiS530 VGA on board. Modem One 56.6 Kbps PCI plug and play modem adapter card with data/fax...
  • Page 49 Keyboard device IBM PS/2-compatible keyboard Serial port 9-pin connector with RS232D electrical interface Parallel port Supports SPP (IBM PC/AT, PS/2) compatible, EPP (IEEE 1284 compliance), ECP (IEEE 1284 compliance) interface. Game port Game port interface for joystick. It also supports MIDI.

  • Page 50: Cmos Reset

    CMOS Reset This system does not deny access to BIOS Setup Utility. Execute “Load BIOS Default Settings” in BIOS Setup to clear the corrupted CMOS data. See “Loading the Default Settings” on page 41. Flash (BIOS) Update Procedure NOTE: The flash update procedure does not change the model number and serial number information in BIOS.

  • Page 51: Bios-Contained Model Number And Serial Number

    BIOS-contained Model Number and Serial Number The model number and serial number information is stored in BIOS ROM and displayed in the “Model Information” of BIOS Setup main menu. If a repair is completed by replacing the system board or installing a new BIOS ROM, then you need to enter the original system model number and serial number in the new BIOS ROM.

  • Page 52: Bios Setup Utility

    Follow these steps to enter Setup when the computer is off: 1. Turn on your monitor. 2. Turn on the system unit. 3. When you see the IBM logo, press F1 to enter Setup and display the Main Menu. Refer to the Setup Utility Main Menu below.
  • Page 53 Loading the Default Settings (Setup Defaults) When you purchase an IBM personal computer, it is already configured for use. The original configuration settings, also called factory or default settings, are stored in the CMOS.

  • Page 54: Start Options

    A dialog box appears saying "SAVE to CMOS and EXIT (Y/N)?" 4. Type Y to select Yes, then press Enter to save the changes in CMOS. You must load the Setup default settings in the following instances: − When you replace the system battery −...
  • Page 55 Virus Warning Determines if the BIOS will monitor the boot sector and partition table of the hard disk drive for any attempt at modification. If any attempt is made, the BIOS will halt the system and an error message will appear. Afterwards, if necessary, you will be able to run an anti-virus program to locate and remove the problem before any damage is done.

  • Page 56: Advanced Setup

    Typematic Delay (Msec) When the typematic rate is enabled, you can select the delay between when the key was first depressed and when the acceleration begins. Security Option Determines the access limitation to the system and Setup, or just Setup. Report No Diskette Drive for Win 95 Select YES to release IRQ6 (Interrupt Request) when the system contains no floppy drive for compatibility with...
  • Page 57 Devices and I/O ports The options in this menu item are used to configure the devices and the I/O ports that this system has. Diskette Drive A Determines the type of Diskette Drive A. PS/2 Mouse Function Determines the mouse function is enabled or disabled. On Board Audio Determine the on board Audio function to be enabled or disabled.
  • Page 58 drives. These drives have a master/slave relationship which is determined by the cabling configuration used to attach them to the controller. PIO means Programmed Input/Output. Rather than have the BIOS issue a series of commands to effect a transfer to or from the disk drive, PIO allows the BIOS to tell the controller what it wants and then let the controller and the CPU perform the complete task by themselves.

  • Page 59: Power Management Setup

    System Shared Memory Size Determines whether 2MB, 4MB, 8MB, 16MB, 32MB, or 64MB of system memory is to be used by video. Init Display First Specify which video subsystem to initialize first. PS/2 Mouse Detect Function Determines whether the power-on self test will check to see if a mouse is attached to the mouse connector.
  • Page 60 Activity Monitor MODEM Use IRQ Allows you to select the IRQ to be used by the modem. HDD Port Activity When set to enabled, any activity taking place at the hard disk or diskette drive will awaken the computer from a powered- down/stndby state.

  • Page 61: Isa Legacy Resource

    ISA Legacy Resource ISA legacy resources (DMA, Interrupts, Memory) are resources that used by ISA adapters which are not Plug-and- Play adapters. Don’t use this setting due to the computer only support PCI adapter cards. CLOCK Generator Configuration This setting allows you to change the clock rate of CPU, SDRAM, DIMM and PCI bus.

  • Page 62: Specifications

    Specifications Dimensions (width x depth x height): • System unit: For machine type 2193, 2194 and 6345: − 190 mm (7.48 in.) x 370 mm (14.57 in.) x 380 mm (14.96 in.) For machine type 2196, 2197 and 6344: −...

  • Page 63: Operating Requirements

    Operating Requirements All machines require two power inputs: one on the system unit and one on the monitor display. The system unit comes with a voltage selector switch, allowing selection of either 115 V ac or 230 V ac. This switch must be in the 230 V ac position when the machine is plugged into a 230 V ac electrical outlet.

  • Page 65: Check Procedures

    Check Procedures Check Procedures ............53 Introduction ..............54 Start................55 Index of Symptoms, Messages, Error Codes, or Beeps .. 59 Troubleshooting .............. 76 Factory-Installed Storage Devices ......77 Factory-Installed Modem Card ........79 Audio (Not Supported by Diagnostics Program) ..81 CD-ROM Drive............

  • Page 66: Introduction

    Introduction This chapter contains the check procedures used to diagnose the causes of product failures. The diagnostic information consists of: Start: This is the starting point for any diagnostic action. Based on high-level symptoms, the check procedure directs you to more detailed procedures to help resolve machine failures.

  • Page 67: Start

    POST error codes and error messages are displayed on the screen after the IBM logo. A beep will precede each error code or message. Please refer to “Index of Symptoms, Messages, Error Codes, or Beeps” on page 59 for additional help.
  • Page 68 Power off the system unit before moving it or when replacing FRUs. Remove all adapter cards, except for the factory- installed modem adapter card and any other IBM factory-installed adapter cards. Disconnect any drives except: 3.5-in. diskette drive...
  • Page 69 Note any symptoms, messages, error codes, or beeps. Make sure that there are no diskettes or CDs in the drives. 002 - DOES AN IBM LOGO SCREEN APPEAR? (YES, READ AHEAD. NO, GO TO STEP 004.) Insert the diagnostics diskette in the diskette drive. 003 -...
  • Page 70 007 - The system configuration report shows only those devices supported by the diagnostics diskette. If a device is missing from the list and is not factory installed, refer to the service manual provided for that device. 008 - DOES THE DIAGNOSTICS FINISH WITHOUT ANY ERRORS? (YES, READ AHEAD.

  • Page 71: Index Of Symptoms, Messages, Error Codes, Or Beeps

    Index of Symptoms, Messages, Error Codes, or Beeps How to Use Error Messages: Use the messages, error codes, and beeps combinations that occur to diagnose failures. If more than one failure occurs, diagnose from the first failure that appears. The cause of the first failure can result in false messages, error codes, or beeps.
  • Page 72 NOTES: If an error message and incorrect audio response occur, diagnose the error message first. If you cannot run the diagnostics program tests but did receive a POST error code, diagnose the POST error message. If you did not receive any error message, look for a description of your error symptoms in “Error Symptoms List”...
  • Page 73 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, Beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
  • Page 74 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, Beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
  • Page 75 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, Beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
  • Page 76 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, Beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
  • Page 77 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, Beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
  • Page 78 Table 2-2 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, Beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
  • Page 79 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 80 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 81 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 82 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 83 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 84 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 85 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 86 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 87 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.

  • Page 88: Troubleshooting

    Troubleshooting Failing Parts or Assemblies: The check procedures generally help you trace a problem to one part or assembly. The last step of the specific check procedure you are using indicates that a part or assembly is failing. You should inspect the part or assembly before you decide to replace it.

  • Page 89: Factory-Installed Storage Devices

    Factory-Installed Storage Devices Use this check procedure to test any factory-installed drives. ATTENTION: The customer may have customized settings in the Setup Utility (other than default settings) on the computer you are servicing. Running the Setup Utility might alter those settings. Take note of the current settings and verify that the customer settings are in place when service is complete.
  • Page 90 IDE connector. (Please refer to the connectors and functions illustrated in chapter 5.) IDE Secondary Channel Master and Slave Drives in BIOS Setup should be connected to the system board secondary IDE connector. (Please refer to the connectors and functions illustrated in chapter 5.) NOTE: The CD-ROM drive that comes with system unit should be configured as IDE Secondary...

  • Page 91: Factory-Installed Modem Card

    Factory-Installed Modem Card 001 - START Power off the system unit. In Windows 98 Device Manager, make sure that the modem is not configured with a conflicting COM port and IRQ setting. Make sure that the communication software is configured with the correct COM and IRQ settings (same as COM port and IRQ as the modem).
  • Page 92 004 - CAN THE MODEM DIAL OUT AND CONNECT TO ANY BBS SUCCESSFULLY? (YES, READ AHEAD. NO, GO TO STEP 005.) The modem adapter functions normally. End. 005 - Make sure that Windows 98 is properly installed, then power off the system unit. Plug the modem adapter card into a different PCI slot.

  • Page 93: Audio (Not Supported By Diagnostics Program)

    Audio (Not Supported by Diagnostics Program) NOTE: Audio tests for the sound card cannot be carried out in the PC Doctor DOS diagnostics program. It is, however, possible to carry out a dial tone test for the modem. While performing this check, you may need to enter and exit Microsoft Windows 98 several times.
  • Page 94 004 - Perform the following under Windows 98. NOTE: If an operating system other than Microsoft Windows 98 is installed, the program screens and icons may differ from these instructions. 1. Start Microsoft Windows 98. 2. Select the Start icon. 3.

  • Page 95: Cd-Rom Drive

    CD-ROM Drive 001 - START Insert the diagnostics diskette into the diskette drive and make sure that there is no CD in the CD-ROM drive. Select Interactive Tests menu, then select and execute CD-ROM Test. 002 - DO YOU SEE A MESSAGE “NO CD-ROM DRIVE OR MSCDEX DEVICE DRIVER INSTALLED.”...

  • Page 96: Memory

    Memory 001 - START Power off the system unit. Insert the diagnostics diskette into the diskette drive. Make sure that all DIMMs are installed correctly. Power on the system unit. Take note of any messages, error codes, or symptoms. 002 - DO YOU RECEIVE POST MEMORY ERROR MESSAGE? (YES, READ AHEAD.

  • Page 97: Keyboard

    Keyboard 001 - START Power off the system unit and make sure that the keyboard plug is connected properly. 002 - Insert the diagnostics diskette into the diskette drive and power on the system unit. Select Interactive Tests menu, then execute Keyboard test.

  • Page 98: Mouse

    Mouse NOTE: A sticking key button can cause the mouse to operate incorrectly. If you suspect this, go to "Keyboard" on page 85. 001 - START Make sure that the mouse ball turns freely. Make sure that the mouse plug connects properly. 002 - Power off the system unit.
  • Page 99 008 - ARE THERE ANY BROKEN PINS IN THE MOUSE PLUG? (YES, GO TO STEP 010. NO, READ AHEAD.) Try with a known good mouse. 009 - DO THE ERROR SYMPTOMS STILL REMAIN? (YES, READ AHEAD. NO, GO TO STEP 010.) Replace the system board.

  • Page 100: Power Supply

    Power Supply 001 - START Power off the system unit. Check the power cord for continuity. Replace if necessary. Check for the correct line voltage from the power outlet, and verify that the voltage selector switch is set to the correct voltage.
  • Page 101 Figure 2-1 Power Supply Connectors (Bottom View) Figure 2-2 Hard Drive or CD-ROM End of Power Cable Figure 2-3 3.5-In. Diskette Drive End of Power Cable 006 - ARE THE VOLTAGES CORRECT AND DOES THE FAN RUN? (YES, READ AHEAD. NO, GO TO STEP 009) The power supply is working normally.
  • Page 102 page 93. If the fan stops running when a drive connector is plugged back in, go to "Start" on page 55. 007 - DO YOU HAVE AN OHM READING WHEN THE SWITCH IS PRESSED AND AN OPEN READING WHEN THE SWITCH IS RELEASED? (YES, READ AHEAD.

  • Page 103: Monitor

    Monitor First, set the system to VGA mode. To do this in Windows 98, press the F8 function key during startup. Safe mode (VGA) will be set for Windows 98. Use the operating system’s video setup to change the monitor resolution. If the monitor type is set to the power saving mode, the screen remains black and the LED lights or flashes in amber color.
  • Page 104 Go to “Index of Symptoms, Messages, Error Codes, or Beeps” on page 59. NOTE: You might have to adjust the monitor controls to obtain the best image. 003 - DOES THE MONITOR SUCCESSFULLY PASS ALL TESTS? (YES, READ AHEAD. NO, GO TO STEP 004) You have successfully completed the video diagnostics tests.

  • Page 105: Undetermined Problems

    Check all cables and connectors for proper installation. If the jumpers, switch, and voltage settings are correct, return here and continue: 3. Remove or disconnect the following, one at a time: Non-IBM devices External devices Any adapters Modem card, if installed...

  • Page 107: Diagnostic Aids

    Diagnostic Aids Diagnostic Aids............. 95 Introduction ..............96 Power-On Self Test............96 Diagnostics Tools............97 Using Diagnostics Program from Recovery CD..97 Diagnostics Program Features........98...

  • Page 108: Introduction

    BIOS version and system memory tested. 3. If an error is detected during POST, the IBM logo screen will automatically switch to the text-based screen and display the error message or code with a beep.

  • Page 109: Diagnostics Tools

    Messages, Error Codes, or Beeps” on page 59 to find the most likely cause and countermeasure. Diagnostics Tools IMPORTANT: This manual is intended to test the IBM machine types 2193, 2194, 2196, 2197, 6344 and 6345 only. Testing devices which are not...

  • Page 110: Diagnostics Program Features

    Diagnostics Program Features Diagnostics program (PC-Doctor for DOS) includes the following features. Table 3-1 Diagnostics Program Main Menu Selections Main Menu Selections Submenu Selections • System Test Diagnostics • Memory Test • Hard Disk Test • Floppy Disk Test • All Tests •...
  • Page 111 Table 3-1 Diagnostics Program Main Menu Selections Main Menu Selections Submenu Selections • Onboard Ethernet Hardware Info • USB Port • System Configuration • Memory Contents • IRQ and DMA Use • Device Drivers • COM and LPT Ports • Physical Disk Drives •...

  • Page 113: Repair Information

    Repair Information Repair Information ............101 Removals and Replacements for machine type 2193, 2194 and 6345................ 102 Identifying the Parts of the System Unit ....103 Top Cover..............105 Adapter Cards ............106 Diskette Drive ............108 CD-ROM Drive............110 Hard Disk Drive............

  • Page 114: Removals And Replacements For Machine Types 2193, 2194 And 6345

    Removals and Replacements for machine type 2193, 2194, and 6345 BEFORE REMOVING ANY FRU, POWER-OFF THE COMPUTER UNPLUG ALL POWER CORDS FROM ELECTRICAL OUTLETS, THEN DISCONNECT ANY INTERCONNECTING CABLES. ATTENTION: The System board, processors, adapter cards, DIMMs, and upgrade processors can be damaged by electrostatic discharge.

  • Page 115: Identifying The Parts Of The System Unit

    Identifying the Parts of the System Unit This computer system has 3 bays, each bay has an factory- installed drive in it. The devices are 3.5” Diskette, 40X CD- ROM drive and 5.0 GB hard disk (some models may have hard disk of 10 or 15 GB capacity).
  • Page 116 1. Power Supply This is a 95-watt switching power supply. 2. CD-ROM Drive This machine has a factory-installed 40X CDROM drive. 3. Bay 2 This drive can accommodate a 5.25” device. 4. Hard Disk Drive This machine has a factory-installed 5.25” 5 (10 or 15) GB hard disk drive.

  • Page 117: Top Cover

    Top Cover To remove the top cover of this system unit: Remove the 4 screws that secure the top cover at the back of the system unit. Hold both sides of the system unit cover and push it backward about 25 mm. Lift the top cover up to remove it completely.

  • Page 118: Adapter Cards

    Adapter Cards Installing Adapter Cards Remove the screw that secures the adapter card retainer and slot cover. Then remove the card retainer and slot cover. Align and insert the adapter card into the adapter card connector. Secure the card with the screw that you removed in the first step.
  • Page 119 Removing Adapter Cards Follow these steps to remove an adapter card: Position the system unit so that the card is accessible to you. If the adapter card has cables, disconnect them. Be sure to take note of where the cable are connected. You will have to reconnect these cables when you reinstall the card.

  • Page 120: Diskette Drive

    Diskette Drive To remove the diskette drive : Disconnect the power and signal cables from the back of the diskette drive. Pivot the latch that secures the lower drive mounting tray. Slide the drive mounting tray toward the rear of the computer and remove it.
  • Page 121 Pull the diskette drive from the mounting tray to remove...

  • Page 122: Cd-Rom Drive

    CD-ROM Drive To remove CD-ROM Drive: Disconnect the power, sound and signal cables from the CD-ROM. Remove the four screws (two on each side) that hold the CD-ROM drive to the chassis. Open the door on the front of the computer. Slide the CD-ROM drive forward through the front opening and remove it.

  • Page 123: Hard Disk Drive

    Hard Disk Drive To remove or replace the hard disk drive: Make sure to disconnect the power and signal cables from the CD-ROM drive and the diskette drive. Pivot the latch that secures the lower drive mounting tray. Slide the drive mounting tray toward the rear of the computer and remove it.

  • Page 124: System Board

    System Board To remove the system board from the system: You must remove the adapter cards first. Disconnect the power cable, CD-ROM cable, Diskette Drive cable, Hard Disk Drive cable, audio cable, power switch cable, speaker cable and LED cable from system board.
  • Page 125 Layout of the System Board of Machine Type 2193 1. DIMM 11. PCI SLOT 1 2. Power Switch connector 12. PCI SLOT 2 3. CPU Fan Connector 13. PCI SLOT 3 4. Hard Disk Drive LED and 14. USB Power LED 5.
  • Page 126 Layout of the System Board of Machine Type 2194 and 6345 1. DIMM 11. PCI SLOT 1 2. Power Switch connector 12. PCI SLOT 2 3. CPU Fan Connector 13. PCI SLOT 3 4. Hard Disk Drive LED and 14. USB Power LED 5.

  • Page 127: Power Supply

    Power Supply This system has a 95-watt switching power supply. 1. To remove the power supply. You must remove the top cover first. 2. Disconnect the power cable from the riser board and all drives. 3. Remove the screws in the machine rear that secure the power supply.

  • Page 128: Removals And Replacements For Machine Types 2196, 2197

    Removals and Replacements for machine type 2196, 2197 and 6344 BEFORE REMOVING ANY FRU, POWER-OFF THE COMPUTER UNPLUG ALL POWER CORDS FROM ELECTRICAL OUTLETS, THEN DISCONNECT ANY INTERCONNECTING CABLES. ATTENTION: The System board, processors, adapter cards, DIMMs, and upgrade processors can be damaged by electrostatic discharge.

  • Page 129: Identifying The Parts Of The System Unit

    Identifying the Parts of the System Unit This computer system has 3 bays; each bay has a factory- installed drive in it. The devices are 3.5” Diskette, 40X CD- ROM drive and 5.0 GB hard disk (some models may have hard disk of 10 or 15 GB capacity).
  • Page 130 7. Hard Disk Drive This machine has a factory-installed 5.25” 4 (6 or 8) GB hard disk drive. 8. System board 9. PCMCIA drive adapter card...

  • Page 131: Top Cover

    Top Cover To remove the top cover of this system unit: Remove the screws that secure the top cover at the back of the system unit. Hold both sides of the system unit top cover and push it forward about 25 inches. Lift the top cover up to remove it completely.

  • Page 132: Adapter Cards

    Adapter Cards Installing Adapter Cards Remove the screw that secures the adapter card retainer and slot cover. Then remove the card retainer and slot cover. Align and insert the adapter card into the adapter card connector. Secure the card with the screw that you removed in the first step.

  • Page 133: Diskette Drive

    Diskette Drive To remove the diskette drive: Disconnect the power and signal cables from the back of the diskette drive. Pull up the latch that secures the drive mounting tray. Slide the drive mounting tray toward the front of the computer and remove it.

  • Page 134: Cd-Rom Drive

    CD-ROM Drive To remove CD-ROM Drive: Disconnect the power, sound and signal cables from the CD-ROM. Pull up the latch that secures the CD-ROM drive mounting tray. Slide the drive mounting tray toward the front of the computer and remove it. Remove four screws (two on each side) that secure the bay holder.

  • Page 135: Hard Disk Drive

    Hard Disk Drive To remove or replace the hard disk drive: Follow the above steps to remove the CD-ROM. Make sure to disconnect the power cord and signal cables from the hard disk drive and the diskette drive. Remove the screws that secure the bay holder that holds the hard diskette drive.

  • Page 136: System Board

    System Board To remove the system board from the system: To remove the system board. You must remove the adapter cards first. Disconnect the power cable, CD-ROM cable, Diskette Drive cable, Hard Disk Drive cable, audio cable, power switch cable, speaker cable and LED cable from system board.
  • Page 137 Layout of system board with SiS540 core logic chip set (machine type 2196) 1. DIMM 11. PCI SLOT 1 2. Power Switch connector 12. PCI SLOT 2 3. CPU Fan Connector 13. PCI SLOT 3 4. Hard Disk Drive LED and 14.
  • Page 138 Layout of system board with SiS630 core logic chip set (machine type 2197 and 6344) 1. DIMM 11. PCI SLOT 1 2. Power Switch connector 12. PCI SLOT 2 3. CPU Fan Connector 13. PCI SLOT 3 4. Hard Disk Drive Led and 14.

  • Page 139: Power Supply

    Power Supply This system has a 95-watt switching power supply. 1. To remove the power supply. You must remove the top cover first. 2. Disconnect the power cable from the riser board and all drives. 3. Remove the screws in the machine rear that secure the power supply.

  • Page 141: Parts/Test Point Locations

    Layout of the System Board of Machine Types 2197 and 6344................131 Jumper Settings............132 Connectors and Functions ........133 Layout of the System Board of Machine Types 2193 and 2196................ 134 Jumper Settings............135 Connectors and Functions ........136 Power Supply Cable Connector Specifications....

  • Page 142: Introduction

    Introduction This chapter contains system board layouts and jumper settings. It is useful when you are asked to measure voltages. Use this information to help you locate parts such as electronic boards, connectors, pin numbers, and test points. This chapter also contains jumper settings for the hard disk drive, CD-ROM (compact disc-read-only memory) drive, and the connector information for modem adapter card.

  • Page 143: Layout Of The System Board Of Machine Types 2197 And 6344

    Layout of the System Board of Machine Types 2197 and 6344 NOTE: The blackened pin of a jumper represents pin 1. Figure 5-1 Jumpers and Connectors Locations of System Board of Machine Types 2197 and 6344. NOTE: See Appendix B for Jumper and Connector Settings for the System Board of Machine Types 2194 and 6345.

  • Page 144: Jumper Settings

    Jumper Settings of the System Board of Machine Types 2197 and 6344 Table 5-1 Jumper/Settings Function Bus Frequency(MHz) JP10 JP11 JP13 CPUCLK SDRAMCLK 2-3 2-3 1-2 2-3 1-2 2-3 1-2 1-2 2-3 2-3 CPU Core Clock Multiplier Jumper connected CPU Clock Frequency Ratio JP1 ..........

  • Page 145: Connectors And Functions

    Connectors and Functions of the System Board of Machine Types 2197 and 6344 Table 5-2 Connector Function BAT 1 Battery socket Floppy 1 Floppy connector CPU FAN LAN and USB connector PCI Slot 1 PCI Slot 2 PCI Slot 3 Power and HDD LED Power Switch connector Hard Disk connector (Primary IDE)

  • Page 146: Layout Of The System Board Of Machine Types 2193 And 2196

    Layout of the System Board of Machine Types 2193 and 2196 NOTE: The blackened pin of a jumper represents pin 1. Figure 5-2 Jumpers and Connectors Locations of the System Board of Machine Type 2193 and 2196...

  • Page 147: Jumper Settings

    Jumper Settings of the System Board of Machine Types 2193 and 2196 Table 5-3 Jumper/Settings Function Bus Frequency(MHz) JP1 JP2 JP3 JP4 CPUCLK PCICLK 1-2 1-2 2-3 1-2 2-3 2-3 2-3 1-2 1-2 1-2 CPU Core Clock Multiplier Jumper connected...

  • Page 148: Connectors And Functions

    Connectors and Functions of the System Board of Machine Types 2193 and 2196 Table 5-4 Connector Function BAT 1 Battery socket ATX Power connector CPU FAN Connector Hard Disk connector (Primary IDE) CD-ROM Drive connector (Secondary IDE) USB and LAN connector...

  • Page 149: Power Supply Cable Connector Specifications

    Power Supply Cable Connector Specifications Refer to the following figures when checking for voltages on power supply cable connectors. When checking voltages, the power supply fan must be running. To power on the power supply without using the on/off switch, use a screwdriver or other tools to short the power supply connector (with the switch cable disconnected from the connector on the system board) or use a connection (jumper) to short the black and green wires of the 20-pin...

  • Page 150: Main Output Pin Assignment

    Main Output Pin Assignment Table 5-5 Main Output Pin Assignment Function Color +3.3 V Orange 3.3 V Orange COMMON BLACK +5Vdc COMMON BLACK +5Vdc COMMON BLACK POWER GOOD GRAY +5Vs PURPLE +12Vdc YELLOW 3.3V Orange -12Vdc BLUE COMMON BLACK P.S-on GREEN COMMON BLACK...
  • Page 151 Figure 5-4 Hard Drive or CD-ROM Power Cable Connector Figure 5-5 3.5-In. Diskette Drive Power Cable Connector...

  • Page 152: Factory-Installed Modem Card Layout

    Factory-Installed Modem Card Layout Figure 5-6 Factory-Installed Modem Card Layout Factory-Installed Modem Card Connector Functions Table 5-6 Factory-Installed Modem Card Connector Functions Item Function Connect to… Telephone line-out Telephone set Some modem adapters may come without this jack. Telephone line-in Telephone line NOTE: Care should be taken while connecting the...

  • Page 153: 3.5-In. Hard Disk Drive Jumper Locations & Settings

    3.5-In. Hard Disk Drive Jumper Locations & Settings Figure 5-7 3.5-In. Hard Disk (Maxtor) Jumper Settings Locations Back of Drive (Quantum) AT Interface connector Jumper Configurations Slave Master Cable Select CS DS GNDGND Jumper Default DS with CS Reserved Setting Shown in Position for Slaves...

  • Page 154: Cd-Rom Drive

    CD-ROM Drive Figure 5-8 CD-ROM Front Panel NOTE: Position of CD-ROM switches and LEDs may vary from illustration. Table 5-7 CD-ROM Front Panel Introduction Item Description Load / eject button Headphone jack Power-on / busy indicator, lights up in green color while disc is set in ready state;...

  • Page 155: Rear Panel Connectors And Features

    CD-ROM Drive Rear Panel Connectors and Features CABLE SELECT SLAVE DC INPUT AUDIO MASTER IDE INTERFACE NOT USED C S M R G G L S L A Figure 5-9 CD-ROM Rear Panel Table 5-8 CD-ROM Drive Rear Panel Connectors and Features Item Function...

  • Page 156: Dimm Configurations

    DIMM Configurations The system board has two DIMM sockets. A maximum of 256KB memory may be installed. You can install 16MB, 32MB, 64MB, or 128MB DIMM in any sockets and with any combinations. System Board Connector Pin Signals Monitor Port Signals Pin Signal Name Signal Name Red Video...

  • Page 157: Parallel Port Signals

    Parallel Port Signals Pin Signal Name Signal Name Strobe Auto Feed Data Bit 0 Error Data Bit 1 Initialize Data Bit 2 Select (In) Data Bit 3 Ground Power Data Bit 4 Ground Power Data Bit 5 Ground Power Data Bit 6 Ground Power Data Bit 7...

  • Page 158: Diskette Drive Cable Connector Signals

    Diskette Drive Cable Connector Signals Signal Name Pin Signal Name No Connection N/A 18 Direction SELECT Density Select Ground No Connection N/A 20 Step High Density Out Ground Ground N/A 22 Write Data No Connection N/A 23 Ground Ground N/A 24 Write GATE Index Ground...

  • Page 159: Ide Cable Connector Signals

    IDE Cable Connector Signals Pin Signal Name Pin Signal Name Host Reset DMA Request Ground Ground Power Host Data 7 Host IOW Host Data 8 Ground Power Host Data 6 Host IOR Host Data 9 Ground Power Host Data 5 I/O Channel Ready Host Data 10 No Connection...

  • Page 161: Safety Inspection Guide

    Safety Inspection Guide Safety Inspection Guide ..........149 General Guidelines ............150...

  • Page 162: General Guidelines

    If any unsafe conditions are present, you must find out how serious the hazard is and if you can continue before you correct the hazard. All current IBM service supplements outlining feature/model changes, along with the machine history, should be reviewed. Check the following items: Damaged, missing, or changed parts, especially in the area of the On/Off switch and the power supply.

  • Page 163: Parts Catalog

    Parts Catalog Parts Catalog..............151 Parts Catalog of machine type 2193, 2194 and 6345 ..152 Assembly 1 : System Unit .......... 152 Assembly 2 : Diskette Drive, Hard Disk Drive ..... 155 Assembly 3 : CD-ROM, Modem Card......156 Assembly 4 : Keyboard and Mouse ......

  • Page 164: Parts Catalog Of Machine Type 2193, 2194 And 6345

    Parts Catalog of machine type 2193, 2194 and 6345 Assembly 1 : System Unit Asm-Index FRU Number Description Gigabyte 810E, GA- 19K3582 6WMMC7/e1 System board AMD K6-2-533MHz 19K3286 100FSB E7 (w/o heatsink and fan) AMD K6-2-550MHz 19K3412 100FSB E7 (w/o heatsink and fan)
  • Page 165 19K3356 32MB module (PC100) 19K3293 64MB module (PC133) 19K3294 128MB module (PC133) 19K3309 95W Power Supply Power Cord 13F9959 US/CE/CF/Taiwan Power Cord 13F9959 LA – Lo Voltage Power Cord 13F9978 LA – HI Voltage 13F9939 Power Cord Brazil 36L8879 Power Cord APU Countries Power Cord 14F0032 UK/HK/Singapore...
  • Page 166 LED Cable Assembly CMOS Backup Battery 1-21 36L9077 (CR2032) 1-22 09N5409 Screw Pack Microphone 1-23 19K3312 Andrea Noise Cancelling, NC8 Speaker Cable, Internal, Used 1-24 19K3366 w/P&d Card MT/DT Y Audio Cable (for Gigabyte 19K3580 board) 19K3521 Y Audio Cable (for 2193)

  • Page 167: Assembly 2 : Diskette Drive, Hard Disk Drive

    Assembly 2 : Diskette Drive, Hard Disk Drive Asm-Index FRU Number Description 19K3298 5 GB Hard Disk Drive, 3.5” 10K2059 10 GB Hard Disk Drive, 3.5” 19K3299 15 GB Hard Disk Drive, 3.5” 19K3355 20 GB Hard Disk Drive, 3.5” 36L9130 3.5”, Diskette Drive 19K3319...

  • Page 168: Assembly 3 : Cd-Rom, Modem Card

    32XCD-RW, White 40XCD-ROM, Black 19K3349 Bezel 19K3358 CD-ROM Cable 09N5406 CD-ROM Audio Cable (2194) 19K3337 CD-ROM Audio Cable (2193) 19K3302 40X/8X DVD-ROM, White 40X/8X DVD-ROM, Black 19K3350 Bezel Modem, 56K Data Fax, GVC O9N5440 NA/LA/SA/TW/HK/China/ Japan Modem, 56K Data Fax, GVC...
  • Page 169 Modem, 56K Data Fax, 09N5443 ASKEY EMEA Modem, 56K Data Fax, 10K2136 Askey ANZ/India/Singapore 36L9016 7FT Phone Cord 09N5423 7FT Phone Cord, HK Modem Phone Cable Adapter 01N1872 Modem Phone Cable Adapter 01N1874 Modem Phone Cable Adapter 60H6043 Spain/Southern Ireland Modem Phone Cable Adapter 60H6045 Modem Phone Cable Adapter...

  • Page 170: Assembly 4 : Keyboard And Mouse

    Assembly 4 : Keyboard and Mouse Asm-Index FRU Number Description 10L6145 Mouse, Badger 28L1865 Mouse, Scrollpoint II Keyboard, Rapid Access II 37L2590 104 US ENGLISH 103P Keyboard, 37L2591 105 FR CANADIAN 058 (Commercial) Keyboard, 37L2592 105 FR CANADIAN 445 (Consumer) 37L2593 105 LA SPANISH 171 37L2594...
  • Page 171 37L2604 105 PORTUGUESE 163 37L2605 105 SPANISH 172 37L2606 105 SWED/FINNISH 153 37L2607 105 SWISS 150 37L2608 105 UK ENGLISH 166 104 US ENGLISH-EMEA 103P 37L2609 37L2610 109 JAPANESE 194 37L2611 104 CHINESE/US 467 HK/TW 37L2612 105 BELGIUM FRENCH 120 37L2640 105 ICELANDIC 197 PC Next-Lite Model A...
  • Page 172 105 PALM REST EURO 37L2527 GREEK 319 104 PALM REST 37L2528 HEBREW 212 105 PALM REST 37L2529 HUNGARIAN 208 105 PALM REST 37L2530 ICELANDIC 197 105 PALM REST EURO 37L2531 ITALY 142 105 PALM REST EURO 37L2532 NORWEGIAN 155 105 PALM REST 37L2533 POLISH 214 105 PALM REST...
  • Page 173 104 PALM REST CHINESE/US 37L2548 104 PALM REST 37L2550 THAILAND 191 107 PALM REST 37L2517 BRAZILIAN/PORTUGUESE 275 109 PALM REST 37L2547 JAPANESE 194 28L1860 KOREAN 413 Passive Speaker, Zylux Tier 3 (No Adapter Req’d) No Logo, 19K3310 Pearl White w/Sky Blue Grill, PC99 Passive Speaker, Infinity Tier 2 19k3311...

  • Page 174: Parts Catalog Of Machine Type 2196, 2197 And 6344

    Parts Catalog of machine type 2196, 2197 and 6344 Assembly 1: System Unit Asm-Index FRU Number Description 19K3284 Pro283 System board 19K3285 Pro286 System board 19K3584 MSI-6188 810E AMD K6-2-533MHz 19K3286 100FSB E7 (w/o heatsink and fan) AMD K6-2-550MHz 19K3412 100FSB E7 (w/o heatsink and fan) 19K3288...
  • Page 175 Fansink, Supports K6-2 and 19K3348 Celeron Processors 19K3292 Fansink, Supports PIII Processors 19K3356 32MB module (PC100) 19K3293 64MB module (PC133) 19K3294 128MB module (PC133) 19K3309 95W Power Supply (LP) 13F9959 Power Cord US/CE/CF/Taiwan Power Cord 13F9959 LA – Lo Voltage Power Cord 13F9978 LA –...
  • Page 176 Outer (Bezel) Panel (Blue) 1-12 19K3323 w/FDD/PCMCIA/CD-ROM slots Outer (Bezel) Panel 1-12 19K3324 w/FDD/CD-ROM slots, Blue Outer (Bezel) Panel 1-12 19K3325 w/FDD/CD-ROM slots, White Outer (Bezel) Panel w/FDD slot, 1-12 19K3326 White 1-13 19K3327 FDD (Holder) Bracket 1-14 19K3328 HDD (Holder) Bracket 1-15 19K3329 CD-ROM (Holder) Bracket...

  • Page 177: Assembly 2: Diskette Drive, Hard Disk Drive

    Assembly 2: Diskette Drive, Hard Disk Drive Asm-Index FRU Number Description 19K3298 5 GB Hard Disk Drive, 3.5” 10K2059 10 GB Hard Disk Drive, 3.5” 19K3299 15 GB Hard Disk Drive, 3.5” 19K3355 20 GB Hard Disk Drive, 3.5” 36L9130 3.5”, Diskette Drive 19K3341 Hard Disk Drive Cable...

  • Page 178: Assembly 3: Cd-Rom, Modem Card

    Assembly 3: CD-ROM, Modem Card Asm-Index FRU Number Description 19K3360 40X CD-ROM, White 19k3300 48XCD-ROM, White 19K3301 32XCD-RW, White 40XCD-ROM, Black 19K3349 Bezel 19K3342 CD-ROM Cable Audio Cable, CD-ROM 19K3337 (for Pro board)
  • Page 179 Audio Cable, CD-ROM 09N5406 (for MSI board) 19K3302 40X/8X DVD-ROM, White 40X/8X DVD-ROM, Black 19K3350 Bezel Modem, 56K Data Fax, ASKEY 19K3304 w/LP Brkt NA/LA/SA/TW/HK/China Modem, 56K Data Fax, 19K3305 ASKEY w/LP Brkt EMEA Modem, 56K Data Fax, 19K3306 ASKEY w/LP Brkt ANZ/India/Singapore Modem, 56K Data Fax, 19K3307...

  • Page 180: Assembly 4: Keyboard And Mouse

    Assembly 4: Keyboard and Mouse Asm-Index FRU Number Description 10L6145 Mouse, Badger 28L1865 Mouse, Scrollpoint II Keyboard, Rapid Access II 37L2590 104 US ENGLISH 103P 105 FR CANADIAN 058 37L2591 (Commercial) 105 FR CANADIAN 445 37L2592 (Consumer) 37L2593 105 LA SPANISH 171 37L2594 105 BRAZ/PORTUGUESE 275 37L2595...
  • Page 181 37L2602 105 ITALIAN 142 37L2603 105 NORWEGIAN 155 37L2604 105 PORTUGUESE 163 37L2605 105 SPANISH 172 37L2606 105 SWED/FINNISH 153 37L2607 105 SWISS 150 37L2608 105 UK ENGLISH 166 104 US ENGLISH-EMEA 103P 37L2609 37L2610 109 JAPANESE 194 37L2611 104 CHINESE/US 467 HK/TW 37L2612 105 BELGIUM FRENCH 120 37L2640...
  • Page 182 105 PALM REST EURO 37L2526 GERMAN 129 105 PALM REST EURO 37L2527 GREEK 319 104 PALM REST HEBREW 37L2528 105 PALM REST HUNGARIAN 37L2529 105 PALM REST ICELANDIC 37L2530 105 PALM REST EURO ITALY 37L2531 105 PALM REST EURO 37L2532 NORWEGIAN 155 105 PALM REST POLISH...
  • Page 183 109 PALM REST JAPANESE 37L2547 28L1860 KOREAN 413 Passive Speaker, Zylux Tier 2 19K3310 (No Adapter Req’d) No Logo, Blue Grill, PC99 Passive Speaker, Infinity Tier 2 19k3311 (No Adapter Req’d) w/Logo...

  • Page 184: Appendix A. Online Support Information

    Internet World Wide Web sites, the IBM Online HelpCenter support areas, and a Fax-Back service. The IBM Automated Fax-Back System offers a variety of IBM computer-related articles. To access this service, call 800- IBM-3395. The Fax-Back system file library can also be accessed through the PC Company BBS.

  • Page 185: Appendix B. System Board Of Machine Types 2194 And 6345

    Appendix B. System Board of Machine Types 2194 and 6345...
  • Page 186 Layout of System Board of the Machine Type 2194 and 6345 Game & PS/2 COMA JP14 Audio AC97 JP19 JP11 JP18 JP20 JP21 SDRAM 8810 SDRAM JP23 GMCH 82810 810E 6WMMC7-1 ICH/ JP16 JP15 82801 FWH32 DIMM 1 JP13 JP12 JP24 DIMM 2 POWER...
  • Page 187 Jumper and ConnectorSettings of the System Board of the Machine Type 2194 and 6345 I/O Ports Connector USB port. IDE1 For Primary IDE port. IDE2 For Secondary IDE port. For PS/2 Mouse & Keyboard PS/2 port. FLOPPY For Floppy port. For Serial port1 (COM COMA A){Support Modem Ring On}.
  • Page 188 +12V SENSE PWR FAN: Power FAN Connector Pin No. Function GND. +12V SENSE SYS FAN: System FAN Connector Pin No. Function GND. +12V SENSE J9:Buzzer Enable (Optional) Pin No. Function Open Internal Buzzer Disable Close Internal Buzzer Enable J17 RING PWR ON :Internal Modem Card Ring PWR On Pin No.
  • Page 189 CD_R JP11:AUX_IN Pin No. Function AUX_L AUX_R J14:Wake on LAN Pin No. Function +5VSB Signal JP3:TEL –The connector for Modem with internal voice connector. Pin No. Function Phone-in Mono-out JP1:STR Enable Pin No. Function Close STR Enable Open STR Disable (Default) JP14: Case Open Pin No.
  • Page 190 JP15: Timeout Reboot Pin No. Function Open Timeout Reboot. Close No Reboot on Timeout. (Default) JP17: Onboard Sound function (Optional) Pin No. Function 1-2 close Enabled Sound.(Default) 2-3 close Disabled Sound. J13/ J20: USB Port Selection (Optional) Pin No. Function 1-2 close Front Panel USB Port Enabled.
  • Page 191 JP24:FWH Write Protection Pin No. Function Open Normal (Default) Close Write Protection. J12 : For 2X11 PINs Jumper P+P−P− SPKR Soft PWR: Soft Power Connector Open: Normal Operation Short: Power On/Off RES: Reset Switch Open: Normal Operation Short: For Hardware Reset System P+P−...
  • Page 192 SPKR: Speaker Connector PIN 1 : VCC (+) − − − − PIN 2 : NC PIN 3 : NC PIN 4 : Data (−)
  • Page 193 HD: IDE Hard Disk Active LED PIN 1: LED anode (+) PIN 2: LED cathode (− − − − ) GN: Green Function Switch Open : Normal operation Short :Entering Green Mode GD: Green LED PIN 1 : LED anode (+) PIN 2 : LED cathode (−...
  • Page 195 Index Adapter Cards Diagnostic Diskette, 55 Machine Types 2193, Use, 57, 74, 77, 83, 2194 and 6345 84, 85, 86, 91 Installing, 106 Diagnostic Program Removing, 107 Error symptoms, 74 Machine Types 2196, From Recovery CD, 97 2197 and 6344...
  • Page 196 Mouse, 35 PIO Mode, 46 Check Procedure, 86 Mouse Port Removal and Signals, 145 Replacement Multimedia, 34 Machine Types 2193, 2194 and 6345, 111 Machine Types 2196, Online Support 2197 and 6344, 123 Information, 172 Parallel Port, 37, Connector Signals, 147...
  • Page 197 Weight, 50 System Board Connector Pin Signals, Connectors and Functions Machine Types 2194, 2197, 6344 and 6345, 133 Machine Types 2193 and 2196, 136 Jumper Settings Machine Types 2194, 2197, 6344 and 6345, 132 Machine Types 2193 and 2196, 135...
  • Page 198 Printed in U.S.A. International Business Machines Corporation Old Orchard Road, Armonk, New York 10504 Part Number: 19K2493 Pub Number: S19K-2493-00 3/00...

This manual is also suitable for:

21946345219663442197

Table of Contents