McIntosh MX120 Owner's Manual page 34

MENU: INPUT SETUP
SOURCE INPUT
TITLE
DIGITAL INPUT
ZONE A ANALOG INPUT
SURR MODE
VIDEO POWER
HDMI VIDEO
COMPONENT VIDEO
MAIN MENU
HDMI Video Input
The MX120 has Electronic Input Switching for four HDMI
Video Sources and they may be assigned to any of the eight
Analog Audio/Digital Inputs. The following example de-
scribes how to reassign HDMI 2 IN Video Input, which by
default has been assigned to TV Input 4, over to the CD(2)
Input 2.
Notes: The MX120 allows for assigning a HDMI Video Input
to multiple Inputs or switched Off. If there are any
Component Video, S-Video or Composite Video Inputs
to be viewed through the HDMI Video Monitor A
Output, it is necessary to select "COMP" in the HDMI
Video Menu Selection for that Input Source.
32. Using the Up or Down
select SOURCE INPUT from the On-Screen Menu,
followed by pressing the Left
push-buttons to select the TV Input, Number 4. Using
the Up or Down
HDMI VIDEO on the On-Screen Menu, followed by
pressing the Left
tons to select NONE.
33. Using the Up or Down
select SOURCE INPUT from on the On-Screen
Menu, followed by pressing the Left
rectional push-buttons to select CD(2) Input 2. Refer
to figure 23.
34. Using the Up or Down
select HDMI VIDEO from the On-Screen Menu, fol-
lowed by pressing the Left
push-buttons to select the Number 2.
35. If you do not wish to perform COMPONENT
VIDEO Adjustments at this time, proceed to How to
Change the Volume Setup on page 37.
34
4 - IR-TV
DVD2
COAX D LK
RCA
CINEMA 1
ON
2
2
Figure 21
directional push-buttons,
or Right directional
directional push-buttons, select
or Right directional push-but-
directional push-buttons,
or Right
directional push-buttons,
or Right directional
MENU: INPUT SETUP
SOURCE INPUT
TITLE
DIGITAL INPUT
ZONE A ANALOG INPUT
SURR MODE
VIDEO POWER
HDMI VIDEO
COMPONENT VIDEO
MAIN MENU
Component Video Input and Video Converter
The MX120 has Electronic Input Switching for three Com-
ponent Video Sources and they may be assigned to any of
the eight Analog Audio/Digital Inputs. The following ex-
ample describes how to reassign COMPONENT 1 IN Video
Input, which by default has been assigned to SAT Input 3,
over to the VCR Input 6.
Note: The MX120 allows for assigning a Component Video
Input to multiple Analog Audio/Digital Inputs or
switched Off.
36. Using the Up
select SOURCE INPUT from the On-Screen Menu,
followed by pressing the Left
push-buttons to select the SAT Input, Number 3. Us-
ing the Up
select COMPONENT VIDEO on the On-Screen
Menu, followed by pressing the Left
rectional push-buttons to select NONE.
37. Using the Up
select SOURCE INPUT from on the On-Screen
Menu, followed by pressing the Left
rectional push-buttons to select VCR Input 6. Refer
to figure 24A.
di-
38. Using the Up
select COMPONENT VIDEO from the On-Screen
Menu, followed by pressing the Left
rectional push-buttons to select the Number 1.
39. If the VCR Input 6 is to be viewed through the HDMI
Monitor A Output, use the Up
tional push-buttons, select HDMI VIDEO on the On-
Screen Menu, followed by pressing the Left
Right directional push-buttons to select COMP. Re-
fer to figure 24B.
4 - IR-TV
DVD2
COAX D LK
RCA
CINEMA 1
OFF
2
2
Figure 22
or Down directional push-buttons,
or Right
or Down directional push-buttons,
or Down directional push-buttons,
or Down directional push-buttons,
or Down
directional
or Right di-
or Right di-
or Right di-
direc-
or