General Information - Philips eXpanium EXP-2461 User Manual

English
CONTROLS
Supplied Accessories:
1 x headphones AY3805
1 x AC/DC adapter AY3162 (not for all versions)
1
CONTROLS ( see figure )
1 ...........................display
2 2;......................switches the player on, starts playback and pauses playback.
3 ESP ....................selects between the battery powersave mode and
Electronic Skip Protection (ESP). ESP prevents playback
interruptions caused by shocks.
4 PROG .................programs tracks and reviews the program.
5 MODE ................selects playback options (e.g. SHUFFLE, REPEAT).
6 DBB ...................switches the bass enhancement on and off. This button also
switches acoustic feedback (the beep) on/off when it is
pressed for more than 2 seconds
7 9 ........................stops playback/clears programmed tracks/ switches off the
set.
8 ∞ /§................skips and searches tracks backward/forward.
3 /4..................MP3 only: skips forward/backward albums.
9 OPEN 2.............opens the CD lid.
p / LINE OUT....3.5mm headphone jack;
0
jack to connect the player to another audio input of an
additional appliance.
! VOL - / +............adjusts the volume.
@ OFF.....................switches HOLD off.
RESUME ...........stores the last position of a CD track played
HOLD .................locks all buttons.
# 4.5V DC..............jack for external power supply.
POWER SUPPLY
Power adapter (supplied or optionally available)
Only use AY3162 adapter (4.5V/450mA DC, positive
pole to the center pin). Any other product may damage
the player.
1
Make sure local voltage corresponds to the power
adapter's voltage.
2
Connect the power adapter to the 4.5V DC jack of the
player and to the outlet.
Helpful Hints:
– Always disconnect the adapter when you are not using it.

GENERAL INFORMATION

CD player and CD handling
• Do not touch the lens A of the CD player.
• Do not expose the unit, batteries or CDs to humidi-
ty, rain, sand or excessive heat (caused by heating
equipment or direct sunlight).
• You can clean the CD player with soft, slightly
dampened, lint-free cloth. Do not use any cleaning
agent as it may have a corrosive effect.
• To clean the CD, wipe it in a straight line from the center toward the edge
using soft, lint-free cloth. The cleaning agent may damage the disc! Never
write on a CD or attach a sticker to it.
• The lens may cloud over when the unit is moved suddenly from cold to warm
surroundings. In that case, playing a CD is not possible. Leave the CD player in
a warm environment until the moisture has evaporated.
• Active mobile phones in the vicinity of the CD player may cause malfunctions.
• Avoid dropping the unit as this may cause damage.
POWER SUPPLY
Batteries (not included)
Inserting AA (LR6, UM3) batteries
1
Open the battery compartment.
2
Insert 2 x AA batteries as shown into the battery compartment.
3
Close the battery compartment.
Helpful Hints:
– Old and new or different types of batteries should
not be combined.
– Remove batteries if they are empty or if the player is
not going to be used for a long time.
Battery indication
The approximate power level of your batteries is shown in the display.
Battery full
Battery two-thirds full
Battery one-third full
Battery dead or empty.When the batteries
are dead or empty, the symbol A flashes,
rP bAtt is displayed, and the beep tone
sounds repeatedly.
Batteries contain chemical substances, so they
should be disposed of properly.
The type plate is located on the bottom of the set.
GENERAL INFORMATION
ENVIRONMENTAL INFORMATION
• All redundant packing material has been omitted. We have done our utmost to
make the packaging easily separable into two mono materials: cardboard (box)
and polyethylene (bags, protective foam sheet).
• Your set consists of materials which can be recycled if disassembled by a spe-
cialized company. Please observe the local regulations regarding the disposal
of packing materials, dead batteries and old equipment.
The set complies with the FCC-Rules, Part 15 and with 21
CFR 1040.10. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
– Apparatus shall not be exposed to dripping or splashing.
– Do not place any sources of danger on the apparatus
(e.g. liquid filled objects, lighted candles)