Advertisement
Quick Links
HPE StoreFabric SN4000B
SAN Extension Switch
Quick Start Instructions
© Copyright 2015, 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice.
The only warranties for Hewlett Packard Enterprise products and
services are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed as
constituting an additional warranty. Hewlett Packard Enterprise shall
not be liable for technical or editorial errors or omissions contained
herein.
Part Number: 5200-0340
Published: January 2016
Edition: 2
*5200-0340*
Overview
Read these instructions to set up and configure the
HPE StoreFabric SN4000B SAN Extension Switch.
These instructions provide basic configuration
steps. For detailed rack mount and configuration
instructions, download the HPE B-series 16Gb FC
Switches Hardware reference guide from the
Hewlett Packard Enterprise website: http://
www.hpe.com/support/sn4000b/manuals.
Figure 1 (page 1) shows the port side of the
SN4000B SAN Extension Switch.
Figure 1 Port side of the SN4000B SAN
Extension Switch
1. System status LED
3. USB port
5. Console port (RJ-45)
7. 16 Gb FC ports (24)
9. 1/10 GbE ports (16)
Verify the carton contents
Verify that the carton contains the following:
One StoreFabric SN4000B SAN Extension
Switch with two integrated power supply/fan
assemblies
Serial cable with an RJ-45 connector
An RJ-45 to DB-9 adapter
Rubber feet, required to set up the switch as
a standalone unit
Brocade EZ switch and China RoHs
documentation
Two power cords
One accessory kit with the following items:
◦
Rack Mount Kit
◦
Hewlett Packard Enterprise product
documentation, including Read Me First,
Quick Start Instructions, Safety Guides,
HPE SAN Visibility CD, User License, and
Warranty.
2. Power status LED
4. Ethernet management port
6. Serial number pull-out tab
8. 40 GbE ports (QSFP+) (2)
Advertisement
Related Manuals for HP StoreFabric SN4000B
Summary of Contents for HP StoreFabric SN4000B
-
Page 1: Quick Start Instructions
Overview Read these instructions to set up and configure the HPE StoreFabric SN4000B SAN Extension Switch. These instructions provide basic configuration steps. For detailed rack mount and configuration instructions, download the HPE B-series 16Gb FC HPE StoreFabric SN4000B Switches Hardware reference guide from the... -
Page 2: Verifying The Installation Requirements
rack. In this installation, the port side of the device is set back from the edge of the rack, allowing a Verifying the installation requirements more gradual bend in the fiber optic cables. To set up the SN4000B SAN Extension switch for The following items are required to install the device the first time, you will need the following: in a rack:... - Page 3 Attach the rear mounting brackets to the rear Assemble the outer rails as follows: rack uprights. Attach the left outer rail and right outer rail to the rear mounting brackets using the Assemble each of the brackets using two #10-32 x 1/2-inch Phillips panhead screws #10-32 x 1/2-inch Phillips panhead screws with captive star lock washers, as shown with captive star lock washers and two...
-
Page 4: Installing A Standalone Switch
Use the screw type #8-32 x 5/16-inch (in the and secure to the outer rail. Repeat for the screw holes marked 16) to attach the two inner other side. See Figure 7 (page 4). rails to the switch. Eight screws are required Figure 7 Securing the front of the switch to for each rail. - Page 5 When the terminal emulator stops reporting Ethernet connection (hub or switch) information, press Enter to display the login Ethernet and Fibre Channel cables prompt. Disk array with Fibre Channel ports Log in to the switch as admin, using the default password, password.
-
Page 6: Switch Setup
If the serial port is no longer required, use the Enter the tsclockserver command to logout command to log out of the serial synchronize local time using NTP: console. Remove the serial cable and replace switch:admin> tsclockserver the plug in the serial port. <ntp1;ntp2>”... - Page 7 Setting the switch features This completes the initial setup of your StoreFabric SN4000B SAN Extension Switch. For detailed instructions on setting all the supported switch features, see the Fabric OS 7.3.x FCIP Administrator's Guide,Fabric OS 7.3.x administrator's guide and the Fabric OS 7.3.x Command reference manual on the Hewlett Packard Enterprise website: http://www.hpe.com/ support/sn4000b/manuals.