Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Neilsen CT3324
Summary of Contents for Neilsen CT3324
- Page 1 Specification of Multifunction Machine MF360...
- Page 2 B65 0JU.U.K.
-
Page 3: Main Technical Parameters
Preface Please read the specification carefully before using the machine; and proceed to operate it rigidly based on the manual in case any incidents occurred to people, machines and tools. Main technical parameters： Parameters Names Parameters values Gasoline engine type Air cooled vertical single-cylinder four-stroke engine Rated power/speed （HP/rpm）... - Page 4 10. handrail 1. fuel tank 11. worm gear clutch handlebar 2. air filter 12. height adjustment handlebar 3. muffler 13. speed controller 4. protective bracket of engine 14. gears joystick 5. rubber tire 15. emergency cut-off handle 6. accessories’ connector bush 16.
-
Page 5: Warning Signs
Warning signs Please read instructions carefully People must keep a safe distance from before using it and operate the the machine. machinery safely when operation. Unplug sparkplug when repairing and maintaining the machine. Don’t touch rotary section of It is necessary to wear safety the rotary tillage knives or goggles and ear protection when otherwise it may cause injury. - Page 6 Spoke end face Worm wheel end face Diagram 7 Diagram 6 7. Disassemble the four nuts M8. See the diagram 8. 8. Assemble the joint linking sleeve and fasten the nuts。See the diagram 9. Accessories’ connector bush NutM8 Diagram 9 Diagram 8 9.
-
Page 7: Operation And Use
Height control hand lever Hand rail Stop pin Diagram 13 Diagram 12 14. Disassemble the two cotter pins and two plastic bags from the gear lever. See the diagram 14. 15. Put two plastic covers on the two gear levers relatively, and then plug the levers in the hole of plastic covers with cotter pin. - Page 8 ● Pull the cotter pin and the gear lever. See the diagram 20. ● Pull the steering hand lever and rotate it in accordance with instruction to suitable position and then disengage it. See the diagram 21. ● Finally assemble the gear lever and cotter pin and arrange all the assemblies. Gear lever Steering hand lever Cotter lever...
- Page 9 Handle for emergency shutdown Adjusting bolt Input clutch handle Output shaft Guard ring Diagram 24 Diagram 23 4. Handle of Output Clutch ● The handle of output clutch mainly controls the work of attachment. ● The attachment start to work when the handle is in the position of ON while it stops working when the handle is in the position of OFF.
- Page 10 6. Gear Control Lever ● There are two gear control levers on this machine, of which one is to control the gear of forward and reverse and the other is to control the gear of rapid and low. See the diagram 27. ●...
- Page 11 2. Turn the handle of output clutch to the position ON. See the diagram 25. 3. For the easy installation of the accessories, please elevate the rear part of gasoline engine for about 20cm to keep the machine almost in the horizontal position. See the diagram 30. Diagram 30 4.
- Page 12 2. Infuse the fuel oil into the fuel tank of the petrol engine ● Choose the specified brand of the fuel oil reasonably. ● Infuse the oil to the position with plate “Fuel level” when refueling the fueling. See the diagram 33 ●Attention: Do not use the adulterants added or water added, unqualified, and improper brand of the fuel oil, they will cause startup difficulty of the petrol engine! Too much fuel oil will also cause petrol engine’s startup difficulty!
- Page 13 11. If the petrol engine is cold start, then slowly move the choke’s handle from “closed” position to “open” position after starting. See the diagram 34. 12. After the petrol engine starts up, please move the speed controller to the lowest speed. After empty running above five minutes and then load or halt the machine.
-
Page 14: Machine Maintenance
2. Machine maintenance ●maintenance list ：Please maintenance the machine strictly according to the following tables; otherwise it may greatly shorten the machine life. Table 1： Operation gap 20 hrs or within 50 hrs or 100hrs or 100 hrs or Every Day the first month every three every six... - Page 15 ● To change lubricating oil of gasoline engine Attention： As the engine oil used is baneful, it cannot be disposed like general waste. Send to the recommended local special recycle bin. 1） Place engine at horizontal position, and put an appropriate container for old oil under the engine. Then remove the oil dipstick, oil drain bolt and gasket.
- Page 16 3）Infuse lubricating oil SAE 80W-90 into oil filler point of gear case, when it comes to the position of L, check with oil dipstick whether oil lever locates between the upper limit and lower limit. Fill in the oil dipstick after that. (See the diagram 40) Upper limit Floor limit...
- Page 17 2）Clean filter core with warm water containing detergent and then dry them out. Drop it into clean lubricating oil SAE 30 and squeeze out the excessive. 3）Clean other elements with warm water containing detergent and then dry them out. 4）Put all the pars back and tighten the wing nut. ●...
- Page 18 0.7mm-0.8mm Diagram 45 2) 3）Screw in the spark plug with hand, and then tighten it with spark plug cap. Attention：1. Overheating or damage may occur on gasoline if not screw down the spark plug; however, over screwing-down may hurt screw thread. 2.