Index - IBM 1403 Field Engineering Maintenance Manual

Acoustical Dampener Device ................................................ 29
Adjusting Individual Hammer-Magnet
Assemblies for Timing and Density................................ 41
Aligning the Hammer to the Paper Path ........................ 38, 89
Aligning the Train to the Hammer ........ .............................. 90
Appendix ................................................................................ 103
Auxiliary Ribbon - Correction Device ................................ 47
Average Edge ................ .......................................................... 95
Base Adjustments and Removals ........ ................ .................. 72
Bevel Gear Unit Lubrication ................................................ 36
Bypass Needle-Valve Adjustment (Pencil Trace) ................ 60
Bypass Needle-Valve Adjustment (Tach-Generator) ............ 64
Carriage Adjustment with the Tachometer-Generator ...... 63
Carriage Adjustments ............................................................ 57
Cartridge Disassembly . ........ ....... .... ........ ................ ................ 75
Cartridge Gear Replacement ................................................ 77
Cartridge Interlock Switch .................................................... 81
Cartridge Mounting .................................... ............................ 98
Center and Upper Plate Reassembly .. ............ ....... ............... 33
Chain Cartridge Disassembly (Out of Machine) .............. 31
Chain Cartridge Removal ...................................................... 30
Chain Cleaning ...................................................................... 31
Chain-Lubricator Adjustment ................................................ 37
Chain Tension ........................................ ................................ 98
Chain-to-Cartridge Reassembly........ .......... ............ ...... ........ 33
Connectors .............................................................................. 102
Contrast ..... ........... ........... ....................................................... 95
Control-Valve-Body Assembly Removal
(Reservoir not Removed) ..... ...... ........ ........ ......... ..... ..... ...... 53
Control-Valve-Body Assembly Removal
(Reservoir Removed) .......................................................... 52
Convenience Outlet .............................................................. 102
Correct Font ............................................................................ 98
Cover Removal ........................................................................ 10
Density .................................................................................... 95
Density Variation ... ....... .......... .......... ...................... ................ 98
Disassembly of the Ribbon-Drive
and Drag Assembly............................................................ 45
Document-Registration Gage ................................................ 96
Double-Space Single-Shot Adjustments ....... .............. ...... ..... 67
Dynamic Adjustment of the Carriage-Tape
Brushes ................................................................................ 71
Emitter-Brush Timing (Pencil Trace) .................................... 63
Emitter Brush Timing (Tach-Generator) .............................. 69
Excessive Oil and Ink ........ ......... ..... ............. .............. ........... 98
Extraneous Ink ........................................................................ 95
Forms Carts Grounding ................................ ........................ 21
Forms Compressor Adjustment .............................................. 91
Forms Compressor Removal and Replacement .................... 84
Forms-Stacker Assembly Adjustment .................................... 20
Forms Thickness Lever .......................................................... 72
Forms-Tractor Adjustment .................................................... 16
Forms-Width Vernier .............................................................. 12
Ground .................................................................................. 102
Index
Hammer-Magnet-Assembly Removal.................................... 39
Hammer Unit Assembly........................................................ 81
Hammer-Unit Removal.................................................... 37, 81
Heavy Stroke Width ............................................................ 100
Horizontal T -Casting Positioning ...... ........................ .... 26, 90
Hydraulic Detent Stop Adjustment ............................ .......... 59
Hydraulic-Pump Drive-Belt Tension .................................... 55
Hydraulic-Unit Oil-Seal Replacement .................................. 56
Hydraulic-Unit Reassembly .................................................. · 54
Hydraulic-Unit Removal ........................................................ 51
Hydraulic-Unit Replacement ................................................ 52
Hydraulic-Unit Reservoir Removal........................................ 52
mM
1416 Train Cartridge .................................................... 75
Impression Control Bar Adjustment ...................................... 91
Individual Hammer Flight-Time Adjustment ...................... 82
Individual Hammer-Magnet-Assembly Adjustment .............. 40
Individual Hammer-Magnet-Coil Replacement ............ 39, 82
Individual Hammer Magnet Removal and Replacement 82
Individual Hammer Removal................ ........ ........................ 40
Individual Hammer Removal and Replacement ................ 85
Individual Pin-Feed Removal .............................................. 16
Individual Slug Removal and Replacement ................ 35, 80
Installation Procedure ........ ..... ... ......... ....... ......... ........ .... ... .... 5
Left Shock-Mount Leveling .................................................. 21
Light Stroke Width (All Characters) ................................ 100
Light Stroke Width (Individual Hammers) ...................... 100
Light Tops or Bottoms ........................................................ 100
Locations ............ ...... ........ ... ..................... ...... ...... ............ ... ... 102
Lower Plate-to-Cartridge Reassembly:........ ...................... ..... 33
Magnet-Assembly Backstop Adjustment ................................ 83
Magnetic Emitter Adjustment .............................................. 61
Magnetic Emitter Timing (Models 3, 4, 5 and 6) .......... 68
Magnetic Emitter Timing (Pencil Trace) ............................ 62
Magnetic Emitter Timing (Tach-Generator) ...................... 68
Magnetic Read-Head Adjustment ........................................ 36
Main Line Switch ................................................................ 102
Manual-Clutch and Line-Selection Knob ............................ 14
Manual Controls - Adjustment .................................... 11, 72
Model 3 - Information Peculiar To .................................... 72
Model 6 Carriage .................................................................. 51
Motor Rotation Check ............................................................ 8
Movable-Base Adjustment .............................................. 23, 72
Movable-Base Eccentric-Shaft Removal ........................ 23, 72
Movable-Base Removal .................................................... 22, 72
New Style Ribbon-Shield Replacement Procedure .............. 44
Oscilloscope Waveform Charts ............................................ 103
Paralleling the Forms Path, Hammers, and Types .............. 98
PCS Transducer Adjustment ................................................ 94
PCS Transducer Output ........................................................ 94
Phantom Printing .......................................................... 95, 100
Pocket Comparator .................................................................. 96
Preventive Maintenance .......................................................... 5
Print Density . ............. ............ ..... ............ ........ ..... ........ .......... 83
Print Density Control........ .......... ............. ................. ............ 72
105