Sony CDX-M1000TF Installation/Connections

FM/MW/LW
Compact Disc
Player
Installation/Connections
安裝 線路連接
CDX-M1000TF
© 2003 Sony Corporation
1
1
4
7
Equipment used in illustrations (not supplied)
插圖中的裝置（非附送）
Front speaker
前揚聲器
Rear speaker
後揚聲器
Active subwoofer
有源超低音揚聲器
3-251-038-31 (1)
Printed in Korea
2 3
5 6
× 4
8
Power amplifier
功率放大器
CD/MD changer
CD/MD 換碟機
Rotary commander RM-X4S
旋轉式控制器 RM-X4S
2 A
B
Cautions
• This unit is designed for negative earth 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all earth wires to a common earth
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
× 2
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit's rating must be higher than the sum of
each component's fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1 is attached to the unit before
shipping. Before mounting the unit, use the
release keys 6 to remove the bracket 1 from
the unit. For details, see "Removing the
bracket (4)" on the reverse side of the sheet.
•Keep the release keys 6 for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
Note
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
AUDIO OUT
SUB OUT (MONO)
FRONT
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
音源選擇器*
XA-C30
BUS CONTROL IN
Connection example (2)
Note (2-A)
Be sure to connect the earth cord before connecting
the amplifier.
Tip (2-B- )
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1
To a metal surface of the car
First connect the black earth lead, then connect
the orange/white striped, yellow, and red power
input leads.
2
To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see "Notes on the control
and power supply leads."
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To a car's illumination signal
Be sure to connect the black earth lead to a
metal surface of the car first.
6
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see "Notes on the control
and power supply leads."
7
To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
Catch
* not supplied
非附送