Related Manuals for Sony BPU4000
Summary of Contents for Sony BPU4000
- Page 1 BASEBAND PROCESSOR UNIT BPU4000 OPERATION MANUAL [English] 1st Edition (Revised 2)
-
Page 2: Table Of Contents
Table of Contents Overview ..............3 Features ................3 System Configuration ............. 5 Name and Function of Parts ........9 Front Panel ..............9 Rear Panel ..............10 Connection and Setup ..........12 4K System Connection ..........12 Extension Mode Connection ......... 13 HD CUTOUT Video System ......... -
Page 3: Overview
3) Requires BPU4000 software version 3.00 or later. signal (HD tri-level sync or SD black burst) from an external 4) If using a HDCU1000-series unit, please contact your Sony device. representative. - Page 4 SZC-2001/SZC-2001M/SZC-2001W HD CUTOUT software Extracts a region, selected by the operator, from the 4K image as an HD image. SZC-4002/SZC-4002M/SZC-4002W HFR software Transfers HFR (High Frame Rate) video and performs signal processing for the following formats. Note that when an HDC4300 is connected, HD 59.94P (2×)/50P (2×) and HD 59.94P (3×)/50P (3×) are supported without installing SZC-4002/4002M/4002W software.
-
Page 5: System Configuration
Note Production of some of the peripherals and related devices shown in the figures may have been discontinued. For advice on choosing devices, please contact your Sony representative. PMW-F55 connection example Connection example of PMW-F55 and HDCU2000/2500 for operation as a system camera. - Page 6 Viewfinder 4K Video 2K Video Monitor Monitor DVF-EL100 CA4000 Camera DVF-L350 System Adaptor Viewfinder Optical fiber cable CCA-5 BPU4000 Lens RCP-1000 series PMW-F55 Solid-state Remote Control Panel Sync signal input Memory Camcorder DC power supply input Return video input Overview...
- Page 7 Connection example of operation using an F65 as a system camera. 4K Video 2K Video HDVF-EL75/L750/L770 Monitor Monitor DVF-L700 Viewfinder DVF-EL100 Viewfinder SKC-4065+CA4000 BPU4000 +SKC-PB40 Lens Optical fiber cable USB flash drive Sync signal input CAC-6 Return Video Digital Motion Picture Return video input Selector Camera...
- Page 8 Monitor Monitor BKW-401 Viewfinder HDVF-C30WR Rotation Bracket HDVF-C35W Viewfinder Lens HDC4300 Color Camera (for ENG/EFP) Optical fiber cable USB flash drive BPU4000 CAC-6 Return Video VCT-14 Tripod Selector Adaptor Intercom Headset CAC-12 Tripod Sync signal input Microphone Microphone Holder Return video input...
-
Page 9: Name And Function Of Parts
Name and Function of Parts Front Panel a b c d MENU REF IN UNLOCK DISP CANCEL COM ERROR POWER FAN STOP OPTICAL CONDITION MENU LOCK MENU ENTER NETWORK BASEBAND PROCESSOR UNIT BPU-4 0 0 0 USB connector (for service personnel) a Red tally light e MENU control block Turns on when a red tally signal is received. -
Page 10: Rear Panel
h Optical signal condition indicators i NETWORK indicator Displays the communications link optical signal level condition Displays the network system connection status. between the video camera, CCU, and the unit. On: Indicates that an external control device (MSU-1000 CAMTBPU: Signal level from the unit to the video camera Master Setup Unit or RCP-1000 series Remote Control CAMtBPU: Signal level from the video camera to the unit Panel) is connected when the CNS MODE setting in <CNS... - Page 11 e CAMERA connector (optical fiber connector) Connects to a video camera using an optical fiber cable. All video camera signals (power supply, control signals, video signal, audio signal, etc.) can be transmitted and received via a single optical fiber cable. f CCU (camera control unit) connector (optical fiber connector) Connects to a camera control unit using an optical fiber cable.
-
Page 12: Connection And Setup
HD signals down-converted from the 4K signal can be output from SLOT3, SLOT4, and the CCU. 1) Requires the SKC-4065 F65 Adaptor. 2) Requires PMW-F55 software version 2.10 or later. 3) Requires BPU4000 software version 3.00 or later. Connection example Prompter (analog) PROMPTER1... -
Page 13: Extension Mode Connection
HD SDI OUT SLOT2 SDI OUT 1 SDI OUT 2 SDI OUT 3 SDI OUT 4 SDI OUT 5 SDI OUT 6 REMOTE BPU4000 OUT 2 OUT 4 OUT 6 OUT 8 Monitor Remote Control Panel HD-SDI Monitor (4K Quad Link) RCP-1500/1501/1530 For details about assignment of BNC connectors, see “Relationship... -
Page 14: Hd Cutout Video System
Settings Device Setting Menu/Page Item Set value BPU4000 Image format settings CONFIGURATION/ SYSTEM RESOLUTION 4096×2160 (4K system) <OUTPUT FORMAT> FORMAT 1920×1080 (HD HFR system) FREQUENCY Frame frequency Video output connector CONFIGURATION/ SLOT1 to Video output format of each settings <OUTPUT FORMAT>... - Page 15 SDI OUT 1 SDI OUT 2 SDI OUT 3 SDI OUT 4 SDI OUT 5 SDI OUT 6 (digital) HD SDI OUT BPU4000 Reference OUT 2 OUT 4 OUT 6 OUT 8 signal input HD SDI Monitor Optical fiber cable...
-
Page 16: Hfr Video System
HFR Video System The BPU4000 can transfer HFR video and perform signal Optional SZC-4002/4002M/4002W software must be installed processing for the following formats according to the to support formats other than 2× and 3× HD. connected camera. Yes: Supported, No: Not supported... - Page 17 SLOT2 SDI OUT 1 SDI OUT 2 SDI OUT 3 SDI OUT 4 SDI OUT 5 SDI OUT 6 (digital) HD SDI OUT BPU4000 Reference signal input Optical fiber cable HD SDI Monitor Prompter signal input PROMPTER IN REFERENCE CAMERA...
- Page 18 SDI OUT 1 SDI OUT 2 SDI OUT 3 SDI OUT 4 SDI OUT 5 SDI OUT 6 (digital) HD SDI OUT BPU4000 Reference LINK-5 LINK-6 LINK-7 LINK-8 signal input Optical fiber cable HD SDI Monitor Prompter signal input PROMPTER IN...
-
Page 19: Relationship Between Connection Type And Bnc Connector Assignment
Relationship between Connection Type and BNC Connector Assignment The names of output interfaces in Table 1 correspond to BNC output interface for the format you want to use in Table 1, then connector assignments in Table 2 (see page 21). Check the check the signal assignments to BNC connectors in Table 2. - Page 20 Operation Frame rate Slot1/Slot2 Slot3 Slot4 mode Output format Output format Output format HD HFR 59.94 (8×) 1080/59.94P (8x) Octa-Link 1080/59.94P (3G), 1080/59.94i (1.5G), 1080/59.94i (1.5G), 720/59.94P (1.5G) 720/59.94P (1.5G) 1080/59.94i (8×), 1.5G 720/59.94P (8×) Quad-Link-2 50 (8×) 1080/50P (8×) Octa-Link 1080/50P (3G), 1080/50i (1.5G), 1080/50i (1.5G),...
- Page 21 Operation Frame rate Slot1/Slot2 Slot3 Slot4 mode Output format Output format Output format HD CUTOUT 59.94 1080/59.94P Perspective 1080/59.94P (3G), 1080/59.94i (1.5G), 1080/59.94i (1.5G), 720/59.94P (1.5G) 720/59.94P (1.5G) 1080/59.94i, 1.5G 720/59.94P 1080/59.94P Simple HD 1080/59.94i, 1.5G 720/59.94P 4K/59.94P 4K (Quad- Link-1) 4K/59.94i 1.5G...
-
Page 22: S-Log2/S-Log3 Compatibility
MAIN Output 4K / HD HFR / HD CUTOUT SLOT1 SLOT2 Operation Output SDI OUT SDI OUT SDI OUT SDI OUT SDI OUT SDI OUT SDI OUT SDI OUT mode format 5- 6 7- 8 5- 6 7- 8 Perspective CUTOUT CUTOUT CUTOUT... - Page 23 When 4K COLOR SPACE (see page 30) is WIDE SLOT1 SLOT2 SLOT3/4 Wide-D mode Color space Gamma Matrix Gamma Matrix Gamma Matrix Standard (Wide-D off) – 2020 2020 Mode 1 SLOT1 4K Normal S-Log2 2020 2020 S-Gamut S-Log2 S-Gamut 2020 S-Gamut3 S-Log3 S-Gamut3...
-
Page 24: Status Display
BPU t CCU: Signal level on the CAMERA connector of CCU Status Display unit. The device and system status can be monitored using text characters superimposed on the output signal configured for the monitor output (M). For details about checking and changing settings, see “Menu Settings”... -
Page 25: Menu Settings
To change page Menu Settings Check that the , cursor is pointing to the page number then push the control knob. The , cursor changes to a flashing ? (question mark). The device and system status can be monitored and settings Flashing can be modified using the menu displayed in the video output configured for the monitor output (M). -
Page 26: Menu Tree
Turn the control knob to move the , cursor to the Menu Tree desired item and push the knob. The , cursor changes to a flashing * (asterisk). The input fields and , cursor are displayed. CONFIGURATION menu Turn the control knob to move the , cursor to the BARS BPU BARS desired input field and push the knob. - Page 27 OPTION KEY READ(USBtCAM) (C12) INSTALLED OPTION HD CUTOUT HD CUTOUT (C13) MODE CUTOUT POSITION CENTER H CENTER V ZOOM CAMERA TILT CAMERA ROLL FOCAL LENGTH a) Not displayed when a CCU is connected. b) Displayed when a CCU is connected. DIAGNOSIS menu OPTICAL LEVEL OPTICAL LEVEL...
-
Page 28: Menu List
Menu List Legend The following conventions are used in the menu tables. Settings ON, OFF, 0, etc.: Factory default settings shown underlined. ENTER to execute: Execute by pushing the control knob or setting the CANCEL/ENTER lever to the ENTER position. CONFIGURATION menu Page name Item... - Page 29 Page name Item Set value Meaning Page No. <OUTPUT FORMAT> SLOT3 SLOT3 output format settings C, M (M:Monitor, C:Clean) When set to M, character text and markers are output on SLOT3. 1920×1080, 1280×720 SLOT3 output video resolution setting EC, LB Edge Crop (EC) and Letter Box (LB) setting.
- Page 30 Page name Item Set value Meaning Page No. <RETURN> SDI1 1080/59.94i(PsF), 1080/59.94P, Format of video signal input on SDI1 connector 1080/50i(PsF), 1080/50P, (display only) NO SIGNAL, --- ---: When a CCU is connected Available only for extension connection. SDI2 1080/59.94i(PsF), 1080/59.94P, Format of video signal input on SDI2 connector 1080/50i(PsF), 1080/50P, (display only)
- Page 31 Page name Item Set value Meaning Page No. <OTHERS> ASSIGNABLE OFF, BPU BARS Assignable button function select SWITCH HD DOWNCONV 1 to 4 4K video signal to HD signal down-converter filter FILTER type CHARACTER LEVEL 1 to 5 Menu character contrast level Selects the output mode for 2×...
- Page 32 Page name Item Set value Meaning Page No. <BOARD STATUS> OK, NG Internal board status OK, NG OK, NG DPR1 OK, NG DPR2 OK, NG <CONNECTION DOCKING OK, NG, --- Video camera connection status (not displayed for STATUS> HDC4300 connection). ---: When camera system adaptor is not connected.
-
Page 33: Appendix
SOFTWARE versions do not match. the life expectancy of these parts is guaranteed. For details on parts replacement, contact your Sony representative. The life expectancy of the electrolytic capacitor is about 5 years under normal operating temperatures and normal usage (8 hours per day; 25 days per month). -
Page 34: Specifications
OPERATION MANUAL (CD-ROM) (1) Specifications Optional accessories United States and Canada: Plug holder B (2-990-242-01) Other areas: Plug holder C (3-613-640-01) United States and Canada: Power cord set (1-551-812-XX) General Other areas: Power cord set (1-782-929-XX) Power requirement 100 V to 240 V AC, 50/60 Hz CCA-5-3 (3 m) and CCA-5-10 (10 m) connection cables Current consumption 1.4 A (max.) - Page 35 DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER. • SONY WILL NOT BE LIABLE FOR CLAIMS OF ANY KIND MADE BY USERS OF THIS UNIT OR MADE BY THIRD PARTIES. • SONY WILL NOT BE LIABLE FOR THE TERMINATION...
- Page 36 The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any...
- Page 37 Sony Corporation BPU4000 (SY) 4-479-647-13 (1) © 2013...