Table of Contents
Advertisement
www.freeservicemanuals.info
NOTE) INERTIA PLATE should be attached so as to ser small
diameter of central round hole above.
Inertia plate
Roller arm assembly
<Note 3e>
NOTE) When attaching ROLLER ARM ASS'Y,
attach the hook(L3c) before the spring(P3a).
NOTE) After attached ROLLER ARM ASS'Y,
tighten screw(S3g) with slit washer(W3a).
(S4a)
(S4a)
k
[4] S/P conveter board
assembly
h
ONLY USED FOR
HR-S6955MS,
HR-S7955MS
[2] Front panel
assembly
ONLY USED
<Note 2b>
FOR HR-S7955MS
(L2a)
(L2b)
Cassette door
<Note 2b>
Knob assembly
The excessive length portion
of wire should be reat as figure.
right side
(WR2b)
<Note 2a>
To Front S Jack board assembly
(S3a)
<Note 3a>
(S3g)
(S2a)
(L3b)
(W3a)
(P3a)
(L3c)
g
e
(S5b)
(S5a)
b
h
a
(L5a)
k
h
a
f
b
(L4a)
c'
f
h
(L6c)
"Z"
(L2c)
PC Support
(L2d)
[2]Mini front board
assembly
(L2a)
(L6a)
f
(L2b)
f
[6] Bottom cover
(L6b)
(WR3b)
<Note 2a>
DRUM
A
Digitized in Heiloo Netherland
Drum assembly
(WR3a)
g
<Note 2a>
(S3b)
d
<Note 3a>
[3] Mechanism assembly
<Note 3b>
d
(S2a)
<Note 3c>
a
(S3c)
(S3e)
c
<Note 3c>
(S3d)
<Note 3c>
c
Insert the bushing of POWER CORD
(S5b)
so as not to twist the cord.
d
c'
e
(S5b)
[5]Main board
assembly
d'
c'
b
b
Switch knob
<Note 2b>
e
d'
c'
For the prevention of the DRUM FPC damage.
b
When you attach the Mechanism assembly on Bottom chassis.
Attach the Mechanism assembly after the positioning boss "z" of the
Bottom chassis is matched to the positioning hole of the Mehcanism assembly.
b
NOTE) INSERT FFC WIRE TO THE CONNECTOR BEFORE
ATTACHING JOG/SW PWB TO F.PANEL.
f
NOTE)INSERT FFC WIRE TO THE CONNECTOR
BEFORE ATTACHING JOG/SW PWB TO F.PANEL.
f
Back side
ADV. Jog board
assembly
CN7003
(L6b)
(L6a)
(S2b)
f
f
(L6a)
(WR4a)
<Note 2a>
back side
back side
Make a crease
Make a crease
CN916
CN511
CN2001
(WR3a)
<Note 2a>
A/C HEAD
To Adv. Jog board assembly
Fig. 1-2-2d
(S1a)
REAR SIDE
JS3001
<Phase alignment>
Accord the position of V gap on R. Encoder and PWB silk " ".
Accord the position of Boss on R. Encoder and PWB silk " ".
NOTE) WHEN YOU FIX FRONT S Jack PWB WITH THE SCREW.
PUT JIG UNDER FRONT PANEL ASS'Y.
Front S Jack board assembly
(WR2a)
<Note 2a>
Front panel assembly back side
Switch lever
<Note 2b>
NOTE
1. Insert direction of FFC WIRE as follows.
Right side
electrode side
2. FFC WIRE and DRUM FPC WIRE should
be insert as follows.
CN5001
OK
CN
3. Insert direction of POWER CORD.
U/U(C)/JPN
WHITE LINE
NEUTRAL
DETAIL "A"
CN7001
Make a crease
B
P/S CONV PWB
About 5cm
right side
(WR2a)
Make a crease
<Note 2a>
3/28/2017
[1] Top cover
(S1a)
(S1b)
(WR2b)
<Note 2a>
(S2c)
Back side
supporting side
NG
90°
CN
CN
Except U/U(C)/JPN
BLUE
NEUTRAL
CN5001
CN5001
ONLY USED
FOR HR-S7955MS
DETAIL "B"
(WR2c)
FRONT PANEL
CN7002
CN7005
(WR2a)
CN7001
Push the FFC wire from the FRONT PANEL
to rear side.
1-3
Hide quick links:
Advertisement
Table of Contents
