Pre-Operation Checks; Operation Mode - Sharp CV-P09FR Service Manual

[5] PRE-OPERATION CHECKS

LOADING BATTERIES
1 Remove the battery cover at the
back of the remote control.
2 Insert batteries into the com-
partment, making sure the
and polarities are correctly
aligned.
• Lines will appear on the display
when batteries are properly in-
stalled.
3
Reattach the battery cover.
4 Press the RESET button using a
thin pointed implement.
NOTES:
• The battery should last approximately one year under normal use.
• When replacing the batteries, always change both batteries at the same time, and
make sure they are the same type.
• If the remote control does not operate normally after replacing the batteries, press
the RESET button using a thin pointed implement.
• If you will not be using the unit for a prolonged period, remove the batteries from the
remote control.

[6] OPERATION MODE

1. Cool mode
Install the exhaust hose (See Page 8), turn the drainage nozzle to the CLOSE 1
position, and check the drainage nozzle is covered with the stopcock.
Drainage nozzle
"CLOSE position"
Stopcock
3
2
3
1
4
Use two AAA (R03) batteries.
Battery cover
1 Press the MODE button to select COOL
mode.
COOL DEHUM FAN VENT
2 Press the ON/OFF button to start op-
eration.
• The red OPERATION lamp ( ) on the
unit will light.
3 Press the TEMPERATURE button to set
the desired temperature.
• The temperature can be set within the range
of 18°C to 32°C.
4 Press the FAN button to set the de-
sired fan speed.
AUTO QUIET LOW HIGH
TO TURN OFF
Press the ON/OFF button again.
• The red OPERATION lamp ( ) on the unit
will turn off.
HOW TO USE THE REMOTE CONTROL
Point the remote control towards the
units signal receiver window and
press the desired button. A beep will
sound when the unit receives the
signal.
• Make sure nothing, such as curtains,
blocks the signal receiver window.
• The remote control operates up to 7
meters away.
CAUTION
• Do not expose the signal receiver window to direct sunlight. This may adversely
affect its operation. If necessary, close the curtains to block out the sunlight.
• Use of a fluorescent lamp in the same room may interfere with transmission of the
signal.
• The unit may be affected by signals emitted from other remote controllers for televi-
sions, VCRs or other equipment used in the same room.
• Do not leave the remote control exposed to direct sunlight or near a heater. Protect
the remote control from moisture and shock which can discolor or damage it.
To prevent the remote control from
being misplaced, hook it to the unit
when not in use.
When attached, to remove the remote
control from the unit, lift the remote
control up slightly and pull it out.
2. Dehumidification mode
In this mode, the air conditioner dehumidifies the room.
Drainage nozzle
Stopcock
"OPEN position"
Hose clamp
Hose
CAUTION
The unit generates heat during dehumidification mode and the room temperature will rise.
Install the exhaust hose if you do not want the room temperature to rise. This will help to
slightly drop the room temperature, but dehumidification performance will become less
effective than when operating without the exhaust hose.
2 – 4
CVP09FR
Remote control hook
1
Remove the exhaust hose (See Page 8)
2 Turn the drainage nozzle to the OPEN
position.
3 Pull the stopcock out from the drainage
nozzle.
• When the stopcock is removed, a small amount
of water may be discharged from the drainage
nozzle.
• Always perform this procedure with the unit
turned off. Drain water will spout out if
attempted during operation.
4 Insert the hose clamp into a standard
commercially-available hose (12.7 mm in-
ner diameter, 16.7 mm outer diameter)
5 Attach the hose to the drainage nozzle,
and secure it with the hose clamp.
• Depending on room condition, approximately
28 liters of water per day (24 hours) will be
dehumidified.
Prepare some kind of bucket of appropriate
size to collect drain water, or take some appro-
priate measure to drain the water outside of the
room, so that drain water will not overflow or
soak your room.
• Set the hose sloping downwards for easier
drainage. Moreover, do not bend the hose at
any point, nor allow the end to be submerged
in water.
6
Press the MODE button to select DEHU-
MIDIFICATION mode.
COOL DEHUM FAN VENT
7
7 Press the ON/OFF button to start opera-
tion.
• The red OPERATION lamp ( )on the unit will
light.
6
• The temperature cannot be set.
• The fan speed is preset to AUTO and cannot
be changed.
TO TURN OFF
Press the ON/OFF button again.
• The red OPERATION lamp ( )on the unit will turn
off.