Philips 40PFL4706 User Manual page 32

Setting items Description
Select this setting if your router has a Wi-Fi
Protected Setup (WPS) button. Start scanning
for wireless networks on the TV after pressing
Easy connect
the WPS button on your router. If connection
test fails, refer to the router's manual for more
details.
Select this setting if your router has Wi-Fi
Protected Setup (WPS) but does not have a
WPS code WPS button. Enter the 8-digit WPS PIN code
shown on your TV in the router settings menu
via PC before [Connect] is selected.
If your wireless network with authentication
setting (WEP, WPA-PSK or WPA2-PSK), WEP /
WPA Key entry screen will appear. Enter
the WEP / WPA key of the selected wireless
network using Î/ï/ Í /Æ, then press OK.
Manual
[Clear]: Clear the entered number or word.
[All clear]: Clear all the entered numbers or
words.
[a/A/@]: Switch between abc, ABC and @ ! ?
[Cancel]: Shows the cancellation display.
OK]: Set the entered number or word.
[
Confi rmation message will appear. Select [Yes] to complete
•
the settings.
3
Press MENU to exit.
Note
•
For a wireless network with authentication setting, key icon appears to the right hand
of the wireless network name (SSID).
•
Signal icon shows the strength of the signal.
•
WEP / WPA key appears as asterisks on the confi rmation screen.
•
The wireless LAN supports following specifi cations.
- Wireless standards : IEEE 802.11 b/g/n
- Frequency spectrum : 2.4GHz
- Security protocol : WEP / WPA / WPA2
Wireless network setting (Manually enter your SSID)
Set up the connection to the Wireless LAN Access Point (AP) (e.g. wireless
router) manually by entering the wireless network name (SSID).
1
Press MENU on the remote control and then use Î/ï/Í/Æ to select
[Setup] > [Installation] > [Network] k k > [Manual network settings] >
[Wireless network setting [ [ ] > [Manually enter your SSID].
• Wireless LAN Access Point (AP) (e.g. wireless router) Name
(SSID) entry screen will appear.
Enter the wireless network name (SSID) using Î/ï/Í /Æ, then
press OK.
[Clear]
: Clear the entered number or word.
[All clear] : Clear all the entered numbers or words.
[a/A/@] : Switch between abc, ABC and @ ! ?
[Cancel] : Shows the cancellation display.
[OK]
: Set the entered number or word.
2
Use Î/ï to select the authentication setting of the selected
wireless network.
• For a wireless network with authentication setting, select the
authentication setting, according to the security type of the
wireless network.
• For a wireless network without authentication setting, select
[None].
[None]
Set the authentication setting to [None].
[WEP]
Set the authentication setting to [WEP].
[WPA-PSK]
Set the authentication setting to [WPA-PSK].
[WPA2-PSK]
Set the authentication setting to [WPA2-PSK].
If you select [WEP], [WPA-PSK] or [WPA2-PSK], WEP / WPA
•
Key entry screen will appear.
Enter the WEP / WPA key of the selected wireless network
using Î/ï/Í /Æ, then press OK.
[Clear]
: Clear the entered number or word.
[All clear] : Clear all the entered numbers or words.
[a/A/@] : Switch between abc, ABC and @ ! ?
[Cancel] : Shows the cancellation display.
[OK]
: Set the entered number or word.
• Confi rmation message will appear. Select [Yes] to complete
the settings.
3
Press MENU to exit.
IP confi guration
In following cases, select [IP confi guration] to set each setting as necessary.
- When connection test failed with the setting of [Connection test].
- When instructed by your internet service provider to make specifi c
settings in accordance with your network environment.
1
Press MENU on the remote control and then use Î/ï/ Í /Æ to
select [Setup] > [Installation] > [Network] k k > [Manual network
settings] > [IP confi guration].
2
Use Î/ï to select a setting and then press OK.
Setting items Description
Auto Sets the IP setting automatically.
IP setting mode
Manual
Sets the IP setting manually.
A set of numbers which are assigned to
IP address * 1, 3
devices participating in a computer network.
A mask which is used to determine what
Subnet mask * 1, 3
subnet an IP address belongs to.
IP address of the network device (such as
Default gateway * 1, 3
router) which provides internet access.
Auto
Sets the DNS setting automatically.
DNS setting
mode
Manual
Sets the DNS setting manually.
A server which handles the name and IP
Primary DNS * 2, 3
address over the internet.
A server which handles the name and IP
Secondary DNS * 2, 3
address over the internet.
An address which recognizes the devices
MAC address connecting to the network. It is also called
Hardware Address.
1
Items can be selected only when [IP setting mode] is set to [Manual].
*
2
* Items can be selected only when [DNS setting mode] is set to [Manual].
3 Use Î/ï or the Number buttons to input numbers. When you press
*
Î/ï to input numbers then press OK or input the triple digits by using
the Number buttons, the cursor moves to the next entry field. When you
press Î/ï to input numbers then press OK or input the triple digits by using
the Number buttons at the rightmost entry field, numbers will be stored and
go back to the previous menu.
3
Press MENU to exit.
Note
•
The range of input numbers is between 0 and 255.
•
If you enter a number larger than 255, the number will automatically be 255.
•
The manually entered number will be saved even if you change the setting to [Auto].
•
When you enter a wrong number, press Color buttons (red) to cancel. (the number will
be back to [0].)
•
If you want to enter 1 or 2 digit number in one cell, press OK to move on to the next cell.
•
If the entered IP address or the default gateway or primary DNS number is same
as the default setting, IP address setting will be set to [Auto]. (The manually entered
number will be saved).
•
When IP address setting is set to [Manual], the setting of DNS setting will
automatically be [Manual] and when IP address setting is set to [Auto], you can set
either [Auto] or [Manual] for DNS setting.
K
EN
31