Page 3
Preface Notebook Computer W310CZ-T Service Manual...
Page 4
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent ven- dor.
Page 5
This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers. It is organized to allow you to look up basic information for servicing and/or upgrading components of the W310CZ-T series notebook PC.
Page 6
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock and injury to per- sons when using any electrical equipment: 1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong mag- netic fields. These can hinder proper performance and damage your data. Take care when using peripheral devices. Use only approved brands of Unplug the power cord before peripherals.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 10
Preface Related Documents You may also need to consult the following manual for additional information: User’s Manual on DVD This describes the notebook PC’s features and the procedures for operating the computer and its ROM-based setup pro- gram. It also describes the installation and operation of the utility programs provided with the notebook PC. FCC Statement This device complies with Part 15 of the FCC Rules.
Preface System Startup 1. Remove all packing materials. 2. Place the computer on a stable surface. 3. Insert the battery and make sure it is locked in position. 4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Preface Contents Introduction ..........1-1 Schematic Diagrams......... B-1 Overview ..................1-1 System Block Diagram ..............B-2 Specifications ..................1-2 Processor 1/7 - DMI, FDI, PEG ............B-3 External Locator - Top View with LCD Panel Open ......1-4 Processor 2/7 - CLK, MISC ............B-4 External Locator - Front & Right Side Views .........1-5 Processor 3/7 - DDR3 ..............B-5 External Locator - Left Side &...
Page 14
Preface Fan, TP, Connector ............... B-31 Power System ................B-32 VDD3, VDD5 ................B-33 POWER 1.5V/0.75V ..............B-34 POWER 1.05VS, VTT_CPU ............B-35 Power 0.85VS, 1.8VS ..............B-36 POWER VCORE1 ............... B-37 POWER VCORE2 ............... B-38 Power AC In, Smart Charger ............B-39 Click Board ..................
Chapter 1: Introduction Overview This manual covers the information you need to service or upgrade the W310CZ-T series notebook computer. Informa- tion about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information about dri-vers (e.g.
Introduction Specifications Processor Options Pointing Device Intel® Celeron™ Processor Built-in Touchpad 1017U (1.60GHz), 1037U (1.80GHz) Interface 2MB L3 Cache, 22nm, DDR3-1600MHz, TDP 17W Three USB 2.0 Ports Core Logic One HDMI-Out Port Latest Specification Information Intel® NM70 Chipset One External Monitor Port The specifications listed here are correct at the One Headphone-Out Jack BIOS...
Page 17
Introduction Communication Built-In 10/100Mb Ethernet LAN (Factory Option) 1M HD PC Camera Module/300K Pixels PC Camera Module (Factory Option) 3G Mini-Card Module WLAN/ Bluetooth Half Mini-Card Modules: (Factory Option) Intel® Centrino® Wireless-N 105 Wire- less LAN (802.11b/g/n) (Factory Option) Intel® Centrino® Wireless-N 135 Wire- less LAN (802.11b/g/n) + Bluetooth 4.0 (Factory Option) Third-Party Wireless LAN (802.11b/g/n) (Factory Option) Third-Party Wireless LAN (802.11b/g/n) +...
Introduction External Locator - Top View with LCD Panel Open Figure 1 Top View 1. PC Camera (Optional) 2. Built-In Microphone 3. *PC Camera LED (1M HD Camera Only) *When the PC camera is in use, the LED will be illuminated in red 4.
Introduction External Locator - Front & Right Side Views Figure 2 Front View 1. LED Indicators FRONT VIEW Figure 3 RIGHT SIDE VIEW Right Side View 1. Microphone-In Jack 2. Headphone-Out Jack 3. USB 2.0 Port External Locator - Front & Right Side Views 1 - 5...
Introduction External Locator - Left Side & Rear View Figure 4 Left Side View 1. Security Lock Slot 2. DC-In Jack 3. RJ-45 LAN Jack LEFT SIDE VIEW 4. External Monitor Port 5. HDMI-Out Port 6. USB Ports 7. Multi-in-1 Card Reader Figure 5 Rear View...
Introduction External Locator - Bottom View Figure 6 Bottom View 1. Battery 2. Speakers 3. Fan Intake/Vent Overheating To prevent your com- puter from overhea- ting, make sure no- thing blocks any vent while the computer is in use. External Locator - Bottom View 1 - 7...
Introduction Mainboard Overview - Top (Connectors) Figure 9 Mainboard Top Connectors 1. RJ-45 Lan Port 2. External Monitor Port 3. HDMI-Out Port 4. USB Port 5. Keyboard Cable Connector 6. Audio Cable Connector 1 - 10 Mainboard Overview - Top (Connectors)
Chapter 2: Disassembly Overview This chapter provides step-by-step instructions for disassembling the W310CZ-T series notebook’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart.
Disassembly NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the battery is removed too). Maintenance Tools The following tools are recommended when working on the notebook PC: • M3 Philips-head screwdriver •...
Disassembly Maintenance Precautions The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a re- moval and/or replacement job, take the following precautions: Power Safety Warning 1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other Before you undertake components could be damaged.
Disassembly Disassembly Steps The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED. To remove the Battery: 1. Remove the battery page 2 - 5 To remove the Keyboard: 1.
Disassembly Removing the Battery 1. Turn the computer off, and turn it over. Figure 1 2. Slide the latch in the direction of the arrow (Figure 1a Battery Removal 3. Slide the latch in the direction of the arrow, and hold it in place (Figure 1a 4.
Disassembly Removing the Keyboard Figure 2 1. Turn off the computer and remove the battery (page 2 - Keyboard Removal 2. Use only the small tool provided (see picture below) to carefully press the four keyboard latches at the top of the keyboard to elevate the keyboard from its normal position (Figure 2a).
Disassembly Removing the Hard Disk Drive Figure 3 HDD Assembly The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm Removal (h) and a speed of 5400 RPM or lower. Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
Page 34
Disassembly 5. Remove the screws Figure 4c Figure 4 6. Slide the hard disk in the direction of arrow (Figure 4d HDD Assembly 7. Lift the hard disk assembly out of the bay (Figure 4e Removal (cont’d.) 8. Remove the screws , and bracket case from the hard disk (Figure 4f...
Page 35
Disassembly Hard Disk Size Note (Foam Rubber Insert) Note that the hard disks pictured on the following pages are all 9.5mm(H) hard disk drives. In some cases 7mm(H) hard disk drives will be installed. For more information contact your distributor/supplier, and bear in mind your warranty terms.
Disassembly Removing the System Memory (RAM) Figure 6 RAM Module The computer has two memory sockets for 200 pin Small Outline Dual In-line Memory Modules (SO-DIMM) supporting Removal DDRIII (DDR3) Up to 1333/1600MHz. The main memory can be expanded up to 8GB. The SO-DIMM modules sup- ported are 1024MB and 2048MB DDRIII Modules.
Page 37
Disassembly 5. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. Figure 7 6. The module will only fit one way as defined by its pin alignment. Make sure the module is seated as far into the slot RAM Module as it will go.
Disassembly Removing the Wireless LAN Module Figure 8 Wireless LAN 1. Turn off the computer, remove the battery (page 2 - 5), keyboard (page 2 - 6), and bottom case (page 2 - Module Removal 2. The Wireless LAN module will be visible at point (Figure 8a on the mainboard.
Part Lists Appendix A:Part Lists This appendix breaks down the W310CZ-T series notebook’s construction into a series of illustrations. The component part numbers are indicated in the tables opposite the drawings. Note: This section indicates the manufacturer’s part numbers. Your organization may use a different system, so be sure to cross-check any relevant documentation.
Part Lists Parts List Illustration Location The following table indicates where to find the appropriate parts list illustration. Table A - 1 Parts List Illustration Parts Location page A - 3 Bottom page A - 4 page A - 5 page A - 6 A - 2 Parts List Illustration Location...
Schematic Diagrams Appendix B: Schematic Diagrams Table B - 1 This appendix has circuit diagrams of the W310CZ-T notebook’s PCB’s. The following table indicates where to find the SCHEMATIC appropriate schematic diagram. DIAGRAMS Diagram - Page Diagram - Page Diagram - Page...
Schematic Diagrams Processor 4/7 - Power POWER Ivy/Sandy Bridge Processor 4/7 PROCESSOR UNCORE POWER VC OR E U34F VTT_CPU N 38 8.5A VCC 1 N 34 AN 48 N 30 VCC 2 VCC IO1 AN 45 VCC 3 VCC IO2 N 26 AN 42 C344...
Schematic Diagrams Processor 7/7 - RSVD Ivy/Sandy Bridge Processor 7/7 ( RESERVED ) CFG Straps for Processor U 34E PEG Static Lane Reversal - CFG2 is for the 16x 1:(Default) Normal Operation; Lane # CFG2 F 48 definition matches socket pin map definition VCC_DIE_SENSE CFG0 C FG[0]...
Schematic Diagrams PCH 8/9 - POWER PantherPoint - M (POWER) CougarPoint power supply range Voltage Rail Voltage S0 Iccmax Current (A) 1.05VS_VCCA_CLK Voltage *HCB1005KF-121T20 V_CPU_IO 1.05 1 (mA) 1.05VS V5REF 1 (mA) 1.00V 1.05V 1.10V POWER U37J 3.3V V5REF_Sus 1 (mA) 1.43V 1.5V 1.58V...
Schematic Diagrams USB 3.0 TI TUSB7320 3.3V_TI 3VA_TI Pin B14 Status Freq. Note (FREQSEL) Need to program *HCB1608KF-121T25 24MHz Pull Hi (R633) Ti's register and C592 C593 C594 C595 C596 C597 C598 C599 C600 C601 C602 PCH Clock out/ set to 24MHz EXT.
Schematic Diagrams Power Switch & LED Board POWER SW & LED S_3.3VS S_3.3VS POWER SJ_SW 1 LED P/N 20mil SWITCH 6-52-56001-023 SMGND SM_BTN# 6-52-56001-028 6-52-56000-020 85204-03001 6-52-56001-022 220_04 HT-150NB-DT 6-53-3150B-245 6-53-3050B-241 6-53-3050B-240 POWER BUTTON SPWR_SW1 SMGND Sheet 41 of 42 TJG-532-V-T/R SM_BTN# Power Switch &...
Schematic Diagrams Power On SEQ W310CZ-D02 POWER ON SEQUENCE DD_ON 1.98ms 3.3V 2.75ms 102.6ms RSMRST# 157.29ms(RSMRST# to PWR_BTN#) 202.38ms 56.19ms PWR_BTN# 102.55ms SUSC# 671.68us 1.5V 1.41ms DDR1.5V_PWRGD 54.8us(SUSC# to SUSB#) SUSB# Sheet 42 of 42 586.9us VTT_MEM Power On SEQ 1.32ms 3.3VS 1.98ms...
Download the BIOS computer model. 1. Go to www.clevo.com.tw and point to E-Services and click E-Channel. Note that BIOS versions 2. Use your user ID and password to access the appropriate download area (BIOS), and download the latest BIOS files...
BIOS Update Use the flash tools to update the BIOS 1. Make sure you are not loading any memory management programs such as HIMEM by holding the F8 key as you see the message “Starting MS-DOS”. You will then be prompted to give “Y” or “N” responses to the programs being loaded by DOS.