Advertisement
Available languages
Available languages
To in-dash receiver
>#18AWG (0.82mm
25A Fuse
Vehicle battery
Vehicle chassis
For power: Connect the 2 yellow power wires from the BassLink DC
harness to the vehicle's + (positive) battery terminal. You must also install
a fuse holder with a 25A fuse within 18" of the battery.
For ground: Connect the 2 black ground wires from the BassLink DC
harness directly to a solid point on the vehicle's chassis. Use sandpaper
to clear the paint from the metal surface at the chassis location. Use a
star-type lock washer to secure the wire.
Remote: Connect the blue/white remote wire from the BassLink DC
harness to the remote output wire on your head unit, if it has one, and
you're using the line-level inputs.
If you have a head unit with speaker-level outputs only: Use speaker
wire to connect the four speaker-level outputs from the head unit to the
four high-level input wires on the BassLink DC's harness. If you have a
head unit with only two speaker-level outputs, you can connect the two
outputs to either the front or rear high-level input wires.
Speaker wire color codes on the BassLink DC wiring harness (the
colors of your vehicle's speaker wires will vary; consult your
owner's manual, or contact a professional for help identifying
them):
Green
Green/black
White
White/black
Purple
Purple/black
Gray
Gray/black
Plugging in the BassLink DC wiring harness: When you've made all
the necessary power and signal connections to the BassLink DC wiring
harness, plug the harness into the input marked "POWER/HIGH-LEVEL
IN".
HARMAN International
Industries, Incorporated
8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.infinityspeakers.com
+12 volt
Remote
Ground
2
) Wire
>#10AWG (5.26mm
2
) Wire
>#10AWG (5.26mm
2
) Wire
Left rear +
Left rear -
Left front +
Left front -
Right rear +
Right rear -
Right front +
Right front -
© 2016 HARMAN International Industries, Incorporated. All rights reserved.
Infinity is a trademark of HARMAN International Industries, Incorporated, registered in the
United States and/or other countries. Features, specifications and appearance are subject to
change without notice.
Line-level Signal Inputs
If you have a head unit with a dedicated subwoofer output
(line-level): Connect the subwoofer output from the head unit to either the
front or rear line-level inputs using an RCA patch cable (sold separately).
If you have a head unit with four line-level outputs: You can use RCA
patch cables to connect all four line-level outputs to the four line-level
inputs on BassLink DC.
If you have a head unit with only two line-level outputs: You can
connect the two outputs to either the front or rear line-level inputs.
INPUT LEVEL SWITCH
If using an aftermarket radio's RCA-level outpus, set the Input Level switch
to the "LO" position. If using high-level outputs, start the control-setting
process with the Input Level switch set in the "HI" or "HI2" position.
AUTO TURN ON Switch
If you did not connect the BassLink DC's remote turn-on connection, set
the Auto Turn On switch to "On". If you did connect the BassLink DC's
remote turn-on connection, set the Auto Turn On switch to "Off".
1. Setting the Gain
Adjusting the gain lets you match the input sensitivity of BassLink DC with
the output of your receiver, and match the relative volume to the rest of
the speakers in your vehicle.
1. Start with gain control set to minimum, and the crossover control and
bass control rotated midway.
2. Choose music with substantial bass content and turn the volume
control on your receiver to ¾ of its total output.
3. Adjust the gain control clockwise, listening carefully to the bass output. If you
hear distortion, turn the gain control counterclockwise to decrease the gain.
4. Switch the phase back and forth to determine which setting provides
the most clean bass output.
5. Adjust the crossover control until the BassLink DC plays only
low-frequency information – you should not hear elements such as
vocals coming from the woofer.
6. Adjust the bass-boost control clockwise or counterclockwise to suit
your taste.
SPECIFICATIONS
Driver Complement
: 10"(250mm) Woofer and 10"(250mm)
Passive Radiator.
Amplifier Power
: 200W RMS
Frequency Response
: 20Hz – 120Hz
Fuse
: 25A
Maximum Current Draw
: 22.6A
Quiescent Current Draw
: <450mA
Input Sensitivity
: 0.05 V – 2.0 V Low-Level Input;
0.5 V – 20V High-Level Input
Crossover Frequency
: 50Hz – 120Hz
Crossover Slope
: 12dB/octave
Bass Boost
: 0dB to +9dB @ 55Hz
Dimensions (L x W x H)
: 14-1/2" x 11-1/4" x 14-3/8"
(367.5mm x 284.8mm x 364.9mm)
Advertisement
