Page 1 2 0 1 7 O W N E R ’ S M A N U A L...
Page 2 This manual illustrates and describes the operation of VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5 INTRODUCTION CONTENTS INTRODUCTION ..... . .4 VEHICLE IDENTIFICATION NUMBER ..6 HOW TO USE THIS MANUAL ... . .4 VEHICLE MODIFICATIONS/ALTERATIONS .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your autho- rized dealer knows your vehicle best, has factory- Congratulations on selecting your new vehicle. Be trained technicians and genuine MOPAR® parts, and assured that it represents precision workmanship, dis- cares about your satisfaction.
Page 7 INTRODUCTION 5 Consult the following table for a description of the symbols that may be used on your vehicle or through- out this Owner’s Manual:...
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision, bodily injury and/or death. It also contains CAU- TIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 9: Table Of Contents
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ To Lock The Doors ....15 A WORD ABOUT YOUR KEYS ... . .9 ▫...
Page 10 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Seat Belt Systems .....25 ▫ Transporting Passengers ....55 ▫...
Page 11: A Word About Your Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 A WORD ABOUT YOUR KEYS Ignition Key Removal The key fob contains the key fob with an integrated 1. Push the brake pedal and place the transmission into mechanical key. To use the mechanical key, simply push first (1) or reverse (R) gear by selecting/pushing the the key release button.
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
Page 13: Locking Doors With A Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Locking Doors With A Key NOTE: A key which has not been programmed is also considered an invalid key, even if it is cut to fit the You can insert the key with either side up. To lock the ignition switch lock cylinder for that vehicle.
Page 14: Replacement Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED NOTE: Only keys that have been programmed to the The Vehicle Security Alarm monitors the doors and vehicle electronics can be used to start the vehicle. Once decklid for unauthorized entry.
Page 15: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 To Arm The System If the alarm emits a visual signal even when the doors and decklid are closed correctly, a system malfunction With the doors and decklid closed and the ignition key has occurred: in this case, contact a authorized vehicle either turned to STOP (OFF/LOCK) or removed, point Dealership.
Page 16: Illuminated Entry
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Disarming NOTE: The interior light is located in the headliner in between the sun visors. The interior light can be set to To completely disable the alarm (e.g. during a lengthy three different positions (Off/Left Position, Center Po- period of vehicle inactivity), lock the vehicle by turning sition, On/Right Position).
Page 17: To Unlock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 NOTE: The door unlock indicator will illuminate in the instrument panel when one or both doors are unlocked. To Lock The Doors Push and release the lock button on the key fob will lock the doors, switching off the internal roof light and single flashing of direction indicators.
Page 18: Key Fob Battery Replacement
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the doors are locked from outside the vehicle (using the key fob), the door lock indicator will illumi- nate for a few seconds and then start flashing (deterrent function). Battery Replacement Procedure 1 —...
Page 19: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Key Fob Screw Location Key Fob Screw Location 3. Remove battery compartment. General Information The following regulatory statement applies to all Radio 4. Replace battery respecting the polarity. Frequency (RF) devices equipped in this vehicle: 5.
Page 20: Door Locks
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly ap- NOTE: Door locking is carried out with all doors shut. proved by the party responsible for compliance could Unlocking Doors From The Outside void the user’s authority to operate the equipment. Push the unlock button on the key fob or turn the metal DOOR LOCKS insert (located inside the key fob) in the driver side door...
Page 21: Locking/Unlocking Doors From The Inside
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Locking/Unlocking Doors From The Inside Push the lock LED indicator button . The button has an LED that indicates whether the doors are locked or unlocked. Pushing the lock LED indicator button again centrally unlocks all doors and switches off the LED.
Page 22: Door Opening/Closing Mechanism Reset
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Opening/Closing Mechanism Reset If the battery is disconnected or the protection fuse blows, the door opening/closing mechanism must be reset as follows: 1. Close all the doors. 2. Push the unlock button on the key fob or the door locking/unlocking LED indicator button on the dashboard.
Page 23 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Continuous Automatic Operation 4. Make sure that the reset is correct by checking that the windows work automatically. This is activated by pushing one of the two buttons for longer than half a second. The window will stop when WARNING! it is fully opened, or when the button is pushed again.
Page 24: Decklid
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DECKLID NOTE: During normal vehicle operation, the luggage compartment can reach temperatures above 149º F (65° C). Pay attention when transporting objects that may be damaged at such temperatures. Do not keep aerosol cans in the vehicle: danger of explosion.
Page 25: Occupant Restraint Systems
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 NOTE: Maintain a tight grip on the decklid when WARNING! raising, in order to prevent any external occurrence (e.g. • The maximum permitted load in the luggage a gust of wind) from suddenly opening the decklid to end of travel.
Page 26: Occupant Restraint Systems Features
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Occupant Restraint Systems Features 3. Children that are not big enough to wear the vehicle seat belt properly (refer to “Child Restraints” in this • Seat Belt Systems section for further information) should be secured in •...
Page 27: Things To Know Before Starting Your Vehicle 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 9. If the air bag system in this vehicle needs to be Research has shown that seat belts save lives, and they modified to accommodate a disabled person, refer to can reduce the seriousness of injuries in a collision. the “If You Need Consumer Assistance”...
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will turn on and remain on until both outboard front Change Of Status seat belts are buckled. The outboard front passenger If the driver or outboard front seat passenger (if seat BeltAlert is not active when an outboard front equipped with outboard front passenger seat BeltAlert) passenger seat is unoccupied.
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with • It is dangerous to ride in a cargo area, inside or lap/shoulder belts. outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously The seat belt webbing retractor will lock only during injured or killed.
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) of the vehicle in a collision, increasing head and • A lap belt worn too high can increase the risk of neck injury. A seat belt worn under the arm can injury in a collision.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Lap/Shoulder Belt Operating Instructions 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 1. Enter the vehicle and close the door. Sit back and adjust the seat.
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt so that it is snug and lies low 6. To release the seat belt, push the red button on the across your hips, below your abdomen. To remove buckle.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretension- ing devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Switchable Automatic Locking Retractor (ALR) around the occupant’s mid-section so as to not activate the ALR. If the ALR is activated, you will hear a clicking The seat belt in the passenger seating position is sound as the seat belt retracts.
Page 35: Supplemental Restraint Systems (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 How To Engage The Automatic Locking Mode WARNING! (Continued) 1. Buckle the combination lap and shoulder belt. • Do not use the Automatic Locking Mode to re- strain occupants who are wearing the seat belt or 2.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Steering Wheel and Column The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses • Instrument Panel power or it becomes disconnected prior to deployment. •...
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 The diagnostics also record the nature of the malfunc- WARNING! tion. While the air bag system is designed to be main- tenance free, if any of the following occurs, have an Ignoring the Air Bag Warning Light in your instru- authorized dealer service...
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) extending your arms to reach the steering wheel or instrument panel. • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 This vehicle may be equipped with a driver and/or WARNING! (Continued) front passenger seat belt buckle switch that detects • Relying on the air bags alone could lead to more whether the driver or front passenger seat belt is severe injuries in a collision.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because air bag sensors measure vehicle deceleration WARNING! over time, vehicle speed and damage by themselves are • Do not drill, cut, or tamper with the knee impact not good indicators of whether or not an air bag should have deployed.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 impacts, in addition to the injury reduction potential impact side of the vehicle during impacts that require provided by the seat belts and body structure. SABIC occupant protection. In side impacts, the SABICs deploy independently;...
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Relying on the SABICs alone could lead to more inflate, even if they are in an infant or child severe injuries in a collision. The SABICs work restraint.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 • Knee Impact Bolsters along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not • Driver and Front Passenger Air Bags permanent and normally heal quickly. However, if •...
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or until the hazard light button is pressed. The WARNING! hazard lights can be deactivated by pressing the hazard light button. Deployed air bags and seat belt pretensioners can- not protect you in another collision. Have the air •...
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Customer Action Customer Will See Customer Action Customer Will See NOTE: Each step MUST BE held for at least two NOTE: Each step MUST BE held for at least two seconds seconds 1.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Action Customer Will See WARNING! (Continued) • It is dangerous to try to repair any part of the air NOTE: Each step MUST BE held for at least two bag system yourself. Be sure to tell anyone who seconds works on your vehicle that it has an air bag Turn hazard flashers...
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Event Data Recorder (EDR) NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded This vehicle is equipped with an event data recorder by the EDR under normal driving conditions and no (EDR).
Page 48: Child Restraints
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraints There are different sizes and types of restraints for children from newborn size to the child almost large Everyone in your vehicle needs to be buckled up at all enough for an adult safety belt. Always check the child times, including babies and children.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Recommended Type Of Child Re- straint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Con- younger and who have not vertible Child Restraint, facing reached the height or weight limits...
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The infant carrier is only used rear-facing in the vehicle. Older Children And Child Restraints It is recommended for children from birth until they Children who are two years old or who have outgrown reach the weight or height limit of the infant carrier.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Children Too Large For Booster Seats WARNING! Children who are large enough to wear the shoulder • Improper installation can lead to failure of an belt comfortably, and whose legs are long enough to infant or child restraint.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belt out of position. If the shoulder belt contacts the face WARNING! or neck, move the child closer to the center of the • Improper installation or failure to properly secure vehicle, or use a booster seat to position the seat belt on the child correctly.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle Automatic Locking Retractor (ALR) Location • ALR = Switchable Automatic Locking Retractor • Top Tether Anchorage Symbol Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when...
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can the head restraints be re- moved? Can the buckle stalk be twisted to Do not twist the buckle stalk in a tighten the seat belt against the belt seating position with an ALR re- path of the child restraint? tractor.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 7. Finally, pull up on any excess webbing to tighten the Installing Child Restraints Using The Top Tether lap portion around the child restraint while you push Anchorage: the child restraint rearward and downward into the vehicle seat.
Page 56: Transporting Pets
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Always use the tether anchor when using the seat belt 2. Route the tether strap around the outboard side of to install a forward facing child restraint, up to the the head restraint to the tether anchorage. recommended weight limit of the child restraint.
Page 57: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • Avoid excessive idling. ENGINE BREAK-IN RECOMMENDATIONS • Check the engine oil level at every fuel fill. A long break-in period is not required for the drivetrain (engine, transmission, and rear axle) in your new ve- SAFETY TIPS hicle.
Page 58: Exhaust Gas
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected WARNING! inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect Exhaust gases can injure or kill.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Air Bag Warning Light WARNING! The light should come on and remain on for four to An improperly attached, damaged, folded, or eight seconds as a bulb check when the ignition is first stacked floor mat, or damaged floor mat fasteners cycled to ON.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • ONLY use the driver’s side floor mat on the • If the vehicle carpet has been removed and re- driver’s side floor area. To check for interference, installed, always properly attach carpet to the with the vehicle properly parked with the engine floor and check the floor mat fasteners are secure...
Page 61: Periodic Safety Checks You Should Make
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Periodic Safety Checks You Should Make Door Latches Outside The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for patterns.
Page 63 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ High Beams ......72 MIRRORS ......63 ▫...
Page 64 62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Indications On Display — If Equipped ..80 TILT/TELESCOPING STEERING COLUMN . . .76 ▫ Fault Indication..... . .81 SPEED CONTROL —...
Page 65: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield but- ton with a counterclockwise rotation and requires no tools for mounting.
Page 66: Power Mirrors
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.
Page 67: Folding Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 Folding Mirrors SEATS The exterior mirrors are hinged to allow the mirror to Seats are a part of the Occupant Restraint System of the pivot forward or rearward to help avoid damage. The vehicle.
Page 68: Manual Seats
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seats Seat Height Adjustment In order to achieve the ideal driving position, the height Forward And Rearward Adjustment of the seats can also be adjusted. Tools are required to The adjusting bar is at the front of the driver seat, near make this height adjustment.
Page 69: Non-Adjustable Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 WARNING! (Continued) • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision, you could slide under the seat belt, which could result in serious injury or death.
Page 70: To Open And Close The Decklid
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE DECKLID CAUTION! • To prevent possible damage, do not slam the decklid to close it. Use a firm downward push at the center of the decklid to ensure the decklid latch is fully engaged.
Page 71 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 3. Move to the rear of the vehicle and lift the decklid. 4. Lift upward on the decklid prop rod to release it from the stowage retainer. Decklid Lift Point Location Decklid Prop Rod Location 1 —...
Page 72: Lights
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Place the decklid prop rod in the decklid slot to WARNING! (Continued) secure the decklid in the open position. contact with engine, or other components, that may be hot and could burn you if touched. •...
Page 73: Headlights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 Multifunction Lever Headlight Operation Headlights NOTE: When the headlights are turned on, the Daytime Running Lights will be deactivated. Rotate the end of the multifunction lever Daytime Running Lights upward to the first detent for headlight To activate the Daytime Running Lights (DRL), rotate operation.
Page 74: High Beams
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beams Turn Signals Move the multifunction lever up or down and the With the low beams activated, pull the multi- arrows on each side of the instrument cluster display function lever towards the steering wheel to turn will flash to show proper operation of the front and rear on the high beams.
Page 75: Dimmer Controls
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 time the lever is pulled, the activation of the lights will Pushing the up or down arrow will increase or decrease be extended by 30 seconds. The activation of the lights the brightness of the instrument panel lights. can be extended to a maximum of 210 seconds.
Page 76: Windshield Wipers And Washers
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the key is removed from the ignition (within CAUTION! two minutes of the ignition being turned OFF), a 10 second timer is activated. Before getting out of the vehicle be sure that the Overhead Dome Lamp is in the center position or •...
Page 77: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Windshield Wiper Operation Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper op- eration. Rotate the end of the lever upward to the second detent past the intermittent settings for high- speed wiper operation.
Page 78: Tilt/Telescoping Steering Column
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the lever is pulled while in the O (off) position, the wipers will operate for three wipe cycles and then turn off. WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles.
Page 79: Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 80: To Set A Desired Speed
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed WARNING! To resume a previously set speed, push the RESUME Leaving the Speed Control system on when not in button, located on the end of the speed control stalk, use is dangerous. You could accidentally set the and release.
Page 81: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Metric Speed (km/h) Metric Speed (km/h) • Tapping the speed control lever up (+) once will • Tapping the speed control lever down (-) once will result in a two km/h increase in set speed. Each result in a two km/h decrease in set speed.
Page 82: Parking Sensors - If Equipped
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKING SENSORS — IF EQUIPPED Acoustic Signal The vehicle’s parking sensors are located in the rear When REVERSE gear is engaged, and there is an bumper, and will detect the presence of any obstacles obstacle behind the vehicle, an acoustic signal is emitted near the rear part of the vehicle while moving in which varies according to the distance of the bumper...
Page 83: Fault Indication
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 The signal is similar for obstacles in the rear left or right area. The arc that corresponds to the position of the obstacle will flash. The color on the instrument cluster display depends on the distance from and position of the obstacle.
Page 84 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Some conditions may influence the performance of the NOTE: The sensor must be free from mud, dirt snow or parking sensors: ice in order for the system to operate correctly. Be careful not to scratch or damage the sensors while •...
Page 85: Power Outlets
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 POWER OUTLETS CAUTION! Your vehicle is equipped with a 12 Volt (13 Amp) power • The Parking Sensor system is only a parking aid outlet that can be used to power cellular phones, small and it is unable to recognize every obstacle, electronics and other low powered electrical accesso- including small obstacles.
Page 86 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power outlet is located on the central tunnel, WARNING! (Continued) between the two cup holders. It only operates with the • If this outlet is mishandled, it may cause an ignition key at MAR/ON. electric shock and failure.
Page 87: Cigar Lighter And Ash Receiver - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 • Do not damage the socket by using unsuitable adap- CAUTION! tors. • Do not exceed the maximum power of 180 Watts CUPHOLDER (15 Amps) at 12 Volts. If the 180 Watts (15 Amps) power rating is exceeded, the fuse protecting the A cupholder is located in the rear of the center console.
Page 88: Storage
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Seatback Storage Located in the back of both the driver and passenger front seats are pockets that can be used for storage. Cargo Pouch Storage Location Rear Compartment Storage CAUTION! • To prevent possible damage, do not slam the Drivers Side Seatback Storage decklid to close it.
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 CAUTION! (Continued) WARNING! transport objects in the luggage compartment that Do not allow children to have access to rear storage may be damaged at such temperatures. Do not compartment. Always close the hood when your place aerosol cans in the luggage compartment.
Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Access the luggage compartment only with the vehicle stationary. Before exiting the vehicle, you should always place the vehicle into FIRST gear or REVERSE, apply the parking brake, and re- move the key from the ignition.
Page 91: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ Change Engine Oil Indicator System ..117 INSTRUMENT PANEL FEATURES ..90 ▫ Trip Computer ..... .118 INSTRUMENT CLUSTER .
Page 92: Instrument Panel Features
90 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Climate Control Air Outlets 6 — Switch Bank (A/C/Door Lock Switch/Door Mirror Demist- ing) 2 — Multifunction Lever 7 — Climate Controls 3 — Instrument Cluster 8 — Driver Air Bag 4 —...
Page 93: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 91 INSTRUMENT CLUSTER • The digital gauge will likely indicate a higher 1. Temperature Gauge • The temperature gauge shows engine coolant tem- temperature when driving in hot weather, or up mountain grades. It should not be allowed to perature.
Page 94: Warning And Indicator Lights
92 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Driving with a hot engine cooling system could 4. Fuel Gauge damage your vehicle. The digital warning light may • The digital display shows the amount of fuel in the switch on (together with a message on the display) to tank.
Page 95: Red Telltale Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 93 information contained in the Owner’s Manual, which All active telltales will display first if applicable. The you are advised to read carefully in all cases. Always system check menu may appear different based upon refer to the information in this chapter in the event of a equipment options and current vehicle status.
Page 96 94 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking Vehicles equipped with the Anti-Lock Brake System capacity in the event of a failure to a portion of the (ABS) are also equipped with Electronic Brake Force hydraulic system.
Page 97 UNDERSTANDING YOUR INSTRUMENT PANEL 95 Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected.
Page 98 96 UNDERSTANDING YOUR INSTRUMENT PANEL Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition is placed in the MAR/ON/RUN position. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as pos- sible.
Page 99 UNDERSTANDING YOUR INSTRUMENT PANEL 97 Transmission Fault Warning Light Red Telltale What It Means Light Transmission Fault Warning Light This light will illuminate (together with a message in the instrument cluster display and a buzzer) to indicate a transmission fault. Contact your authorized dealer if the message re- mains after restarting the engine.
Page 100 98 UNDERSTANDING YOUR INSTRUMENT PANEL Battery Charge Warning Light Red Telltale What It Means Light Battery Charge Warning Light This light illuminates when the battery is not charging properly. If it stays on while the en- gine is running, there may be a malfunction with the charging system. Contact your autho- rized dealer as soon as possible.
Page 101: Yellow Telltale Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 99 Yellow Telltale Indicator Lights Tire Pressure Monitoring System (TPMS) Warning Light Yellow Telltale What It Means Light Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring.
Page 102 100 UNDERSTANDING YOUR INSTRUMENT PANEL Under-inflation also reduces fuel efficiency and tire NOTE: Some external parameters (eg; outdoor tem- tread life, and may affect the vehicle’s handling and perature) may affect TPMS info on your instrument stopping ability. cluster. Please note that the TPMS is not a substitute for proper CAUTION! tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation...
Page 103 UNDERSTANDING YOUR INSTRUMENT PANEL 101 Generic Warning Indicator Light Yellow Telltale What It Means Light Generic Warning Indicator Light The Generic Warning Light will illuminate if any of the following conditions occur: Oil Change Request, Engine Oil Pressure Sensor Failure, External Light Failure, Fuel Cut-Off Not Available, Parking Sensor Failure, DST System Failure.
Page 104 102 UNDERSTANDING YOUR INSTRUMENT PANEL Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light After the ignition is turned on, the Anti-Lock Brake System (ABS) light illuminates to indi- cate function check at vehicle startup. If the light remains on after startup or comes on and stays on at road speeds, it may indicate that the ABS has detected a malfunction or has be- come inoperative.
Page 105 UNDERSTANDING YOUR INSTRUMENT PANEL 103 Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light — If Equipped The “ESC Indicator Light” in the instrument cluster will come on when the ignition is placed in the MAR/ON/RUN position, and when ESC is activated.
Page 106 104 UNDERSTANDING YOUR INSTRUMENT PANEL Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale What It Means Light Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the MAR/ON/RUN position before engine start.
Page 107 UNDERSTANDING YOUR INSTRUMENT PANEL 105 CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.
Page 108: Green Telltale Indicator Lights
106 UNDERSTANDING YOUR INSTRUMENT PANEL Green Telltale Indicator Lights Turn Signal Indicator Lights Green Telltale What It Means Light Turn Signal Indicator Lights The instrument cluster directional arrow will flash independently for the left or right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunction lever is moved down (left) or up (right).
Page 109 UNDERSTANDING YOUR INSTRUMENT PANEL 107 Park/Headlight On Indicator Light Green Telltale What It Means Light Park/Headlight On Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Cruise Control Engaged Indicator Light — If Equipped Green Telltale What It Means Light...
Page 110: White Telltale Indicator Lights
108 UNDERSTANDING YOUR INSTRUMENT PANEL White Telltale Indicator Lights Cruise Control Ready Indicator Light White Telltale What It Means Light Cruise Control Ready Indicator Light This light will turn on when the speed control is on, but not set. Blue Telltale Indicator Lights High Beam Indicator Light Blue Telltale What It Means...
Page 111 UNDERSTANDING YOUR INSTRUMENT PANEL 109 the odometer. Your instrument cluster display is de- The instrument cluster display consists of the following: signed to display important information about your • Digital Speedometer vehicle’s systems and features. Using a driver interac- • Vehicle Info tive display located on the instrument panel, your instrument cluster display can show you how systems •...
Page 112: Instrument Cluster Display Setup Menu
110 UNDERSTANDING YOUR INSTRUMENT PANEL • UP Arrow Button The setup menu can be activated by pushing the SET/BACK button. Single push on the up or down Push and release the up arrow button to scroll arrow button will scroll through the setup menu op- upward through the main menu and sub- tions.
Page 113 UNDERSTANDING YOUR INSTRUMENT PANEL 111 2. Push the up or down arrow button (by a single push) Speed Buzzer (Speed Limit) to select the new setting. With this function, it is possible to set the vehicle speed limit (MPH or km/h) to immediately alert the driver 3.
Page 114 112 UNDERSTANDING YOUR INSTRUMENT PANEL Briefly push the SET/BACK button to go back to the 2. Push and release the up or down arrow button to menu screen, or push and hold the SET/BACK button select the setting and once selected a beep will occur (approximately one second) to go back to the main to signal the setting is saved.
Page 115 UNDERSTANDING YOUR INSTRUMENT PANEL 113 5. Push and release the up or down arrow button for BACK button (approximately one second) to go back to setting. the main screen without storing the settings. 6. Briefly push the SET/BACK button and “minutes” Set Date will flash on the display.
Page 116 114 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The setting will increase or decrease by one button (approximately one second) to go back to the unit each time the up or down arrow button is pushed. main screen without storing the settings. Push and hold the up or down arrow button to Units (Set Units) increase/decrease the setting rapidly.
Page 117 UNDERSTANDING YOUR INSTRUMENT PANEL 115 7. When accessing the “Fuel Economy” submenu, When you have made the required settings, briefly briefly push the SET/BACK button. Either “mpg,” push the SET/BACK button to go back to the submenu “km/l ” or “l/100km” will appear on the display screen, or push and hold the SET/BACK button (ap- (according to the previous setting).
Page 118 116 UNDERSTANDING YOUR INSTRUMENT PANEL Buzzer Volume (Adjusting The Failure/Warning Push the SET/BACK button briefly. The display shows Buzzer Volume) the service interval in miles (mi) or kilometers (km) according to the previous setting (see the Unit Of With this function, the volume of the buzzer accompa- Measurement paragraph).
Page 119: Change Engine Oil Indicator System
UNDERSTANDING YOUR INSTRUMENT PANEL 117 Daytime Running Lamps Push and release the down arrow button to return to the last menu option (Daylights). This function may be used to activate/deactivate the daytime running lamps. Change Engine Oil Indicator System Proceed as follows to switch this function on or off: Your vehicle is equipped with an engine oil 1.
Page 120: Trip Computer
118 UNDERSTANDING YOUR INSTRUMENT PANEL • A short button push displays the different values. NOTE: Consult your authorized dealer if the oil change indicator message does not reset. • A long button push resets the system and then starts a new trip. Trip Computer The Trip Computer is located in the instrument cluster.
Page 121 UNDERSTANDING YOUR INSTRUMENT PANEL 119 “Current Trip” can be used to display the figures Start Of Trip Procedure relating to: With the ignition on, push and hold the TRIP button for over two seconds to reset trip information. NOTE: “Trip B” functions may be excluded (see “Trip B Data”).
Page 122: Values Displayed
120 UNDERSTANDING YOUR INSTRUMENT PANEL Values Displayed Range This indicates the distance which may be traveled with Indications On Display the fuel remaining in the tank, assuming that driving Each time a value is selected, the following information conditions will not change. The message “----” will is shown in the Instrument Cluster Display: appear on the display in the following cases: •...
Page 123: Cybersecurity
UNDERSTANDING YOUR INSTRUMENT PANEL 121 Current Fuel Consumption Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlaw- This indicates the fuel consumption. The value is con- ful access to vehicle systems and wireless communica- stantly updated.
Page 124: Radio System
122 UNDERSTANDING YOUR INSTRUMENT PANEL Privacy of any wireless and wired communications WARNING! (Continued) cannot be assured. Third parties may unlawfully inter- • ONLY insert media (e.g., USB, SD card, or CD) cept information and private communications without into your vehicle if it came from a trusted source. your consent.
Page 125: Radio Operation And Mobile Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 123 RADIO OPERATION AND MOBILE PHONES CLIMATE CONTROLS Under certain conditions, the mobile phone being on in The Climate Control System allows you to regulate the your vehicle can cause erratic or noisy performance temperature, air flow, and direction of air circulating from your radio.
Page 126 124 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Control Descriptions Icon Description A/C Button Press and release to change the current setting, the indicator illuminates when A/C is on. Performing this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off.
Page 127 UNDERSTANDING YOUR INSTRUMENT PANEL 125 Icon Description Demist/Defrost Button Push and release the Demist/Defrost button to turn on the outside mirror defroster. An indicator will illuminate when the outside mirror defroster is on. The outside mirror de- froster automatically turns off after 20 minutes. Temperature Control Knob Temperature control is used to regulate the temperature of the air forced through the cli- mate system.
Page 128 126 UNDERSTANDING YOUR INSTRUMENT PANEL Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 129: Climate Control Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 127 Climate Control Functions 4. Move the Recirculation Control to Heating After demisting/defrosting, operate the controls as normal to restore the required comfort conditions. To heat the passenger compartment, proceed as follows: NOTE: The climate control system is very useful for 1.
Page 130 128 UNDERSTANDING YOUR INSTRUMENT PANEL Ventilation NOTE: The internal air recirculation system makes it possible to reach the required heating or ventilation To ventilate the passenger compartment properly, pro- conditions more quickly. Do not use the internal air ceed as follows: recirculation function on rainy/cold days to avoid the 1.
Page 131 UNDERSTANDING YOUR INSTRUMENT PANEL 129 3. Turn the Blower Control counterclockwise to reduce System Maintenance the fan speed. In winter, the climate control system must be turned on at least once a month for about 10 minutes. Have the Door Mirror Demisting system inspected at an authorized dealer before the summer.
Page 133 STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....134 DRIVING ON SLIPPERY SURFACES ..145 ▫ Automatic Transmission ....134 ▫...
Page 134 132 STARTING AND OPERATING ▫ Cornering Brake Control System (CBC) ..153 ▫ Tire Types ......170 ▫...
Page 135 STARTING AND OPERATING 133 ▫ Fuel System Cautions....186 FUEL REQUIREMENTS — 1750 TURBO ..183 ▫ Reformulated Gasoline ....184 ▫...
Page 136: Starting Procedures
134 STARTING AND OPERATING STARTING PROCEDURES Irrespective of the mode selected (AUTO/MANUAL), to engage FIRST (1st) gear or REVERSE (R), it is Before starting your vehicle, adjust your seat, adjust necessary to press the brake pedal and push the 1 both inside and outside mirrors, and fasten your seat button on the transmission control panel (or the + belts.
Page 137: Cold Weather Operation
STARTING AND OPERATING 135 engine fails to start within 10 seconds, turn the ignition CAUTION! switch to the STOP (OFF/LOCK) position, wait 10 to 15 • Do not attempt to push or tow your vehicle to get seconds, then repeat the “Normal Starting” procedure. it started.
Page 138: Six-Speed Alfa Twin Clutch Transmission
136 STARTING AND OPERATING Although the pump is rubber-mounted for quiet opera- WARNING! (Continued) tion, it is normal to hear it running during this time. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children SIX-SPEED ALFA TWIN CLUTCH TRANSMISSION to be in a vehicle unattended is dangerous for a...
Page 139 STARTING AND OPERATING 137 • Automatic (AUTO) mode: The system shifts between When the key is turned to the ON position, the current transmission gear will be displayed in the instrument all forward gears automatically. cluster, along with the AUTO indicator. This indicates When the “Race”...
Page 140 138 STARTING AND OPERATING When coming to a stop, the transmission will automati- To drive, press the brake pedal, and select 1 (1st) or R cally select FIRST (1st) gear. The driver must manually (REVERSE) using the transmission gear selector buttons upshift the transmission (by tapping the + shift paddle) on the center console.
Page 141 STARTING AND OPERATING 139 threshold within three seconds of the request; other- Neutral (N) wise, the transmission will shift to NEUTRAL (N). Use this range when the vehicle is standing for pro- The driver should then repeat the request for 1st or R longed periods with the engine running.
Page 142 140 STARTING AND OPERATING With the vehicle in motion, to engage a gear from the 1. Make sure that the vehicle has come to a complete NEUTRAL (N) position, push the 1 button on the stop. transmission control panel (it is not necessary to press 2.
Page 143: Alfa Dna System (Dynamic Vehicle Control System)
STARTING AND OPERATING 141 • Dynamic (This mode alters the transmission’s auto- Assist (HSA) will temporarily hold the vehicle in posi- tion when the brake pedal is released. If the accelerator matic shift schedule for sportier driving [D]). pedal is not applied after a short time, the vehicle will •...
Page 144: Driving Modes
142 STARTING AND OPERATING Driving Modes Electronic Stability Control (ESC) and Anti-Slip Regulation (ASR) systems: The Alfa DNA system lever will always return to the center position after use. The ESC and ASR system ensures more enjoyable, sportier driving while guaranteeing the stability of the The selected driving mode is indicated by the corre- vehicle.
Page 145 STARTING AND OPERATING 143 Race Mode Engine And Gearbox/Transmission: Activation The system adjusts the transmission shift calibration for sportier shifting. Starting in Dynamic mode, move the Alfa DNA system lever upwards (to the letter “D”) and hold in this NOTE: In Race mode, the sensitivity of the accelerator position for five seconds, until the Race mode activation pedal increases considerably.
Page 146: System Failure
144 STARTING AND OPERATING Electronic Q2 system: Engine And Gearbox/Transmission: The system is calibrated to ensure the best driving Standard response shifting. comfort. Deactivation Engine And Gearbox/Transmission: To deactivate All Weather mode and return to Natural Standard response shifting. mode, move the Alfa DNA system lever upwards (to letter “D”) and keep it in this position for half a second.
Page 147: Launch Control
STARTING AND OPERATING 145 The display will become grey (same screen as Natural WARNING! mode) but without an indication of the Alfa DNA setting. The display will also show a warning message. Launch Control is intended for off-highway or off-road use only and should not be used on any Please contact your authorized dealer for service.
Page 148: Traction
146 STARTING AND OPERATING • Replace tires when tread wear indicators first become when there is a difference in the surface traction under the rear (driving) wheels. visible. • Keep tires properly inflated. WARNING! • Maintain sufficient distance between your vehicle Rapid acceleration on slippery surfaces is danger- and the vehicle in front of you to avoid a collision in ous.
Page 149: Shallow Standing Water
STARTING AND OPERATING 147 WARNING! (Continued) WARNING! (Continued) • Failure to follow these warnings may result in and cause your vehicle to sink into deeper water. injuries that are serious or fatal to you, your Furthermore, flowing and/or rising water can carry passengers, and others around you.
Page 150: Parking Brake
148 STARTING AND OPERATING CAUTION! (Continued) after driving through standing water. Do not continue to operate the vehicle if any fluid ap- pears contaminated, as this may result in further damage. Such damage is not covered by the New Vehicle Limited Warranty. •...
Page 151: Brake System
STARTING AND OPERATING 149 WARNING! CAUTION! • Never leave children alone in a vehicle, or with If the Brake Warning Light remains on with the access to an unlocked vehicle. parking brake released, a brake system malfunction • Allowing children to be in a vehicle unattended is is indicated.
Page 152: Esc (Electronic Stability Control) System
150 STARTING AND OPERATING ESC (ELECTRONIC STABILITY CONTROL) WARNING! (Continued) SYSTEM in a reckless or dangerous manner which could The ESC system improves the directional control and jeopardize the user’s safety or the safety of others. stability of the vehicle in various driving conditions. •...
Page 153: System Activation
STARTING AND OPERATING 151 • Oversteer: occurs when the vehicle is turning more System Intervention than it should according to the angle of the steering This is indicated by the flashing of the warning light on wheel. the instrument panel, to inform the driver that the •...
Page 154 152 STARTING AND OPERATING The ABS includes an amber ABS Warning Light. When WARNING! (Continued) the light is illuminated, the ABS is not functioning. The • The ABS cannot prevent accidents, including system reverts to standard non-anti-lock brakes. Turn- those due to excessive speed on corners, driving ing the ignition OFF and ON again may reset the ABS if on low-grip surfaces or aquaplaning.
Page 155: Cornering Brake Control System (Cbc)
STARTING AND OPERATING 153 System Intervention AntiSlip Regulation System (ASR) A slight pulsing of the brake pedal and noise indicates WARNING! the intervention of the ABS: this is completely normal when the system intervenes. • Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the Cornering Brake Control System (CBC) vehicle, nor can it increase the traction afforded...
Page 156: Hill Start Assist (Hsa)
154 STARTING AND OPERATING System Intervention WARNING! (Continued) This is indicated by the flashing of the warning light on adversely affect ESC performance. Improperly the instrument panel, to inform the driver that the inflated and unevenly worn tires may also de- vehicle is in critical stability and grip conditions.
Page 157: Hydraulic Brake Assistant System (Hba)
STARTING AND OPERATING 155 When the two seconds have elapsed, without starting, WARNING! (Continued) the system is automatically deactivated, gradually re- • The HBA system cannot prevent accidents, in- leasing the braking pressure. During this release stage, cluding those due to excessive speed on corners, the typical brake disengagement noise, indicating that driving on low-grip surfaces or aquaplaning.
Page 158: Electronic Q2 System (E-Q2)
156 STARTING AND OPERATING The HBA system is deactivated when the brake pedal is TIRE SAFETY INFORMATION released. Tire Markings Electronic Q2 System (E-Q2) The Electronic Q2 system intervenes during accelera- tion on corners, braking the inner drive wheel and thus increasing the traction of the outer wheel (which bears more of the vehicles weight): the torque is thus distrib- uted optimally between the drive wheels in accordance...
Page 159 STARTING AND OPERATING 157 NOTE: tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preced- • P (Passenger) — Metric tire sizing is based on U.S. ing the size designation. Example: LT235/85R16. design standards.
Page 160 158 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 161: Tire Identification Number (Tin)
STARTING AND OPERATING 159 EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification:...
Page 162: Tire Terminology And Definitions
160 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 163 STARTING AND OPERATING 161 Term Definition less than 1 mile (1.6 km) after sitting for a minimum of three hours. Inflation pressure is measured in units of PSI (pounds per square inch) or kPa (kilopascals). Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire.
Page 164: Tire Loading And Tire Pressure
162 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 165 STARTING AND OPERATING 163 Tire And Loading Information Placard WARNING! • Overloading of your tires is dangerous. Overload- ing can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 166 164 STARTING AND OPERATING This placard tells you important information about the: To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of 1. Number of people that can be carried in the vehicle. occupants and cargo should never exceed XXX kg or 2.
Page 167 STARTING AND OPERATING 165 (5) Determine the combined weight of luggage and NOTE: cargo being loaded on the vehicle. That weight may • If your vehicle will be towing a trailer, load from not safely exceed the available cargo and luggage your trailer will be transferred to your vehicle.
Page 168 166 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overload- ing can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 169: Tires - General Information
STARTING AND OPERATING 167 TIRES — GENERAL INFORMATION WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect ve- hicle handling and can fail suddenly, resulting in Proper tire inflation pressure is essential to the safe and loss of vehicle control. satisfactory operation of your vehicle.
Page 170: Tire Inflation Pressures
168 STARTING AND OPERATING Tread Wear CAUTION! Improper cold tire inflation pressures can cause abnor- After inspecting or adjusting the tire pressure, mal wear patterns and reduced tread life, resulting in always reinstall the valve stem cap. This will pre- the need for earlier tire replacement.
Page 171: Tire Pressures For High Speed Operation
STARTING AND OPERATING 169 inflation pressure should be increased by 3 psi (21 kPa), WARNING! (Continued) which equals 1 psi (7 kPa) for every 12°F (7°C) for this serious collision. Do not drive a vehicle loaded to outside temperature condition. the maximum capacity at continuous speeds above Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) 75 mph (120 km/h).
Page 172: Tire Types
170 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and when ambient temperatures are less than 40°F (5°C) or additional information. if roads are covered with ice or snow. For more infor- mation, contact an authorized dealer. Damaged Run Flat tires, or Run Flat tires that have experienced a loss of pressure should be replaced Summer tires do not contain the all season designation...
Page 173: Run Flat Tires - If Equipped
STARTING AND OPERATING 171 Snow Tires Run Flat Tires — If Equipped Some areas of the country require the use of snow tires Run Flat tires allow you the capability to drive 50 miles during the Winter. Snow tires can be identified by a (80 km) at 50 mph (80 km/h) after a rapid loss of “mountain/snowflake”...
Page 174 172 STARTING AND OPERATING tire. Compact spare tire descriptions begin with the CAUTION! letter “T” or “S” preceding the size designation. Ex- ample: T145/80D18 103M. Because of the reduced ground clearance, do not take your vehicle through an automatic car wash T, S = Temporary Spare Tire with a compact or limited use temporary spare Since this tire has limited tread life, the original equip-...
Page 175 STARTING AND OPERATING 173 Collapsible Spare Tire — If Equipped WARNING! The collapsible spare is for temporary emergency use Compact and Collapsible spares are for temporary only. You can identify if your vehicle is equipped with emergency use only. With these spares, do not drive a collapsible spare by looking at the spare tire descrip- more than 50 mph (80 km/h).
Page 176: Tire Spinning
174 STARTING AND OPERATING Limited Use Spare — If Equipped Tire Spinning The limited use spare tire is for temporary emergency When stuck in mud, sand, snow, or ice conditions, do use only. This tire is identified by a label located on the not spin your vehicle’s wheels above 30 mph (48 km/h) limited use spare wheel.
Page 177: Life Of Tire
STARTING AND OPERATING 175 • Driving style. • Tire pressure – Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life, resulting in the need for earlier tire replace- ment.
Page 178: Replacement Tires
176 STARTING AND OPERATING Replacement Tires you may have on tire specifications or capability. Fail- ure to use equivalent replacement tires may adversely The tires on your new vehicle provide a balance of affect the safety, handling, and ride of your vehicle. many characteristics.
Page 179: Tire Chains (Traction Devices)
STARTING AND OPERATING 177 CAUTION! CAUTION! (Continued) it is important that only traction devices in good Replacing original tires with tires of a different size may condition are used. Broken devices can cause result in false speedometer and odometer readings. serious damage.
Page 180: Tire Rotation Recommendations
100. The relative performance of tires depends wear. Alfa Romeo, in collaboration with Pirelli, devel- upon the actual conditions of their use, however, and oped a specific high performance tire for the 4C model.
Page 181: Temperature Grades
STARTING AND OPERATING 179 WARNING! WARNING! The traction grade assigned to this tire is based on The temperature grade for this tire is established straight-ahead braking traction tests, and does not for a tire that is properly inflated and not over- include acceleration, cornering, hydroplaning, or loaded.
Page 182 180 STARTING AND OPERATING also increase as the vehicle is driven, this is normal and (20°C) and the measured tire pressure is 27 psi (186 there should be no adjustment for this increased pres- kPa), a temperature drop to 20°F (-7°C) will decrease sure.
Page 183: Base System
STARTING AND OPERATING 181 • The TPMS is not a substitute for proper tire mainte- CAUTION! (Continued) nance, and it is the driver’s responsibility to maintain After using an aftermarket tire sealant it is recom- correct tire pressure using an accurate tire gauge, mended that you take your vehicle to an autho- even if under-inflation has not reached the level to rized dealership to have your sensor function...
Page 184 182 STARTING AND OPERATING The TPMS consists of the following components: system fault is detected, the “TIRE PRESSURE MONI- TORING UNAVAILABLE” text message will display. If • Receiver Module. the ignition key is cycled, this sequence will repeat • Four Tire Pressure Monitoring Sensors. providing the system fault still exists.
Page 185: General Information
STARTING AND OPERATING 183 2. If you install the compact spare tire in place of a road General Information tire that has a pressure below the low-pressure This device complies with Part 15 of the FCC rules and warning limit, upon the next ignition key cycle, a RSS-210 of Industry Canada.
Page 186: Reformulated Gasoline
184 STARTING AND OPERATING Light spark knock at low engine speeds is not harmful CAUTION! to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate ser- DO NOT use gasoline containing methanol or gaso- vice is required.
Page 187: Cng And Lp Fuel System Modifications
STARTING AND OPERATING 185 If a Non-FFV vehicle is inadvertently fueled with E-85 without MMT. Gasoline blended with MMT reduces fuel, the engine will have some or all of these symp- spark plug life and reduces emissions system perfor- toms: mance in some vehicles.
Page 188: Fuel System Cautions
186 STARTING AND OPERATING Indiscriminate use of fuel system cleaning agents CAUTION! (Continued) should be avoided. Many of these materials intended Most of these products contain high concentra- for gum and varnish removal may contain active sol- tions of methanol. Fuel system damage or vehicle vents or similar ingredients.
Page 189: Adding Fuel/Smart Fuel
STARTING AND OPERATING 187 Refueling Procedure WARNING! (Continued) 1. Open the fuel filler door pulling towards outside. vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.
Page 190 188 STARTING AND OPERATING 2. There is no fuel filler cap. A flap door inside the pipe Emergency Gas Can Refueling: seals the system. Most gas cans will not open the flapper door. A funnel is provided to open the flapper door to allow emergency refueling with a gas can.
Page 191: Trailer Towing
STARTING AND OPERATING 189 3. Ensure funnel is inserted fully to hold flapper door TRAILER TOWING open. Trailer towing with this vehicle is not recommended. 4. Pour fuel into funnel opening. RECREATIONAL TOWING (BEHIND 5. Remove funnel from filler pipe, clean off prior to MOTORHOME, ETC.) putting back in the storage area.
Page 192 190 STARTING AND OPERATING Towing Condition Wheels OFF The Ground Alfa Twin Clutch Transmis- sion Flat Tow None NOT ALLOWED Dolly Tow Front NOT ALLOWED Rear NOT ALLOWED On Trailer...
Page 193: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Jump-Starting Procedure ....201 HAZARD WARNING FLASHER ..192 IF YOUR ENGINE OVERHEATS ..192 FRONT TOW EYE USAGE .
Page 194: Hazard Warning Flasher
192 WHAT TO DO IN EMERGENCIES • On the highways — slow down. HAZARD WARNING FLASHER • In city traffic — while stopped, place the transmis- The Hazard Warning flasher switch is located on the center console. sion in NEUTRAL, but do not increase engine idle speed.
Page 195: Wheel And Tire Torque Specifications
WHAT TO DO IN EMERGENCIES 193 Torque Specifications CAUTION! Lug Nut/Bolt Torque **Lug Nut/ Driving with a hot cooling system could damage Bolt Size Nut/Bolt your vehicle. If the temperature gauge reads 240°F Socket (116°C) or greater pull over and stop the vehicle. Size Idle the vehicle with the air conditioner turned off until the coolant temperature drops back into the...
Page 196: Tire Service Kit
194 WHAT TO DO IN EMERGENCIES Tighten the lug nuts/bolts in a star pattern until each TIRE SERVICE KIT nut/bolt has been tightened twice. Small punctures up to 1/4 inch (6 mm) in the tire tread can be sealed with the Tire Service Kit. Foreign objects (e.g., screws or nails) should not be removed from the tire.
Page 197 WHAT TO DO IN EMERGENCIES 195 Components And Operation Tire Service Kit Components (Bottom View) 1 — Power Plug Tire Service Kit Components (Top View) 2 — Air Pump Hose (Black) 1 — Sealant Cartridge Receptacle 2 — Pressure Gauge 3 —...
Page 198 196 WHAT TO DO IN EMERGENCIES application use and need to be replaced after each use. Always replace these components immediately at your authorized dealer. • When the Tire Service Kit sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel compo- nents.
Page 199 WHAT TO DO IN EMERGENCIES 197 WARNING! (Continued) WARNING! (Continued) • If the tire has any sidewall damage. immediately with plenty of water if there is any • If the tire has any damage from driving with contact with eyes or skin. Change clothing as soon extremely low tire pressure.
Page 200 198 WHAT TO DO IN EMERGENCIES 3. Place the transmission in PARK and place the igni- Injecting Sealant Into The Tire tion in the OFF position. 1. Always start the engine before turning on the Tire 4. Set the parking brake. Service Kit.
Page 201: Jump-Starting
WHAT TO DO IN EMERGENCIES 199 NOTE: WARNING! (Continued) • If the tire does not inflate to at least 26 psi (1.8 Bar) Failure to follow this warning can result in injuries pressure within 15 minutes the tire is too badly that are serious or fatal to you, your passengers, and damaged.
Page 202: Preparations For Jump-Start
200 WHAT TO DO IN EMERGENCIES NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. WARNING! Do not attempt jump-starting if the battery is fro- zen. It could rupture or explode and cause personal injury.
Page 203: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 201 NOTE: Be sure that the disconnected ends of the cables Jump-Starting Procedure do not touch while still connected to the other vehicle. WARNING! 1. Firmly apply the parking brake, and turn the ignition Failure to follow this jump-starting procedure OFF.
Page 204 202 WHAT TO DO IN EMERGENCIES Connecting The Jumper Cables 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then 1. Connect the positive (+) end of the jumper cable to start the engine in the vehicle with the discharged the positive (+) post of the vehicle with the dis- battery.
Page 205: Front Tow Eye Usage
WHAT TO DO IN EMERGENCIES 203 CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular devices, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
Page 206 204 WHAT TO DO IN EMERGENCIES When using a tow eye be sure to follow the “Tow Eye WARNING! Usage Precautions” in this section. Stand clear of vehicles when pulling with tow eyes. • Do not use a chain with a tow eye. Chains may break, causing serious injury or death.
Page 207 WHAT TO DO IN EMERGENCIES 205 CAUTION! (Continued) • In compliance with the above conditions, towing with a tow eye must take place with two vehicles (one towing, the other towed) aligned as much as possible along the same center line. Damage to your vehicle may occur if these guidelines are not followed.
Page 208: Fire Extinguisher - If Equipped
206 WHAT TO DO IN EMERGENCIES FIRE EXTINGUISHER — IF EQUIPPED EVENT DATA RECORDER (EDR) The fire extinguisher is located under the dashboard in This vehicle is equipped with an Event Data Recorder front of the passenger side seat. (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...
Page 209 MAINTAINING YOUR VEHICLE CONTENTS ▫ Body Lubrication ....218 ENGINE COMPARTMENT — 1750 TURBO . . .209 ▫ Wiper Blades ..... . .218 ONBOARD DIAGNOSTIC SYSTEM —...
Page 210 208 MAINTAINING YOUR VEHICLE ▫ License Plate Lights ....253 REPLACEMENT BULBS ....244 ▫...
Page 211: Engine Compartment - 1750 Turbo
MAINTAINING YOUR VEHICLE 209 ENGINE COMPARTMENT — 1750 TURBO 1 — Fuse Box 3 — Engine Oil Dip Stick 5 — Coolant Reservoir 2 — Battery 4 — Engine Oil Fill...
Page 212: Onboard Diagnostic System - Obd Ii
210 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! (Continued) Your vehicle is equipped with a sophisticated onboard • If the MIL is flashing while the engine is running, diagnostic system called OBD II. This system monitors the severe catalytic converter damage and power loss performance of the emissions, engine, and Alfa Twin will soon occur.
Page 213: Emissions Inspection And Maintenance Programs
MAINTAINING YOUR VEHICLE 211 Normally, the OBD II system will be ready. The OBD II WARNING! (Continued) system may not be ready if your vehicle was recently • Be possible that vehicle systems, including serviced, or recently had a dead battery or a battery safety related systems, could be impaired or a replacement.
Page 214: Replacement Parts
212 MAINTAINING YOUR VEHICLE ignition OFF or start the engine. This means that your REPLACEMENT PARTS vehicle’s OBD II system is not ready and you should Use of genuine parts for normal/scheduled mainte- not proceed to the I/M station. nance and repairs is highly recommended to ensure the •...
Page 215: Maintenance Procedures
MAINTAINING YOUR VEHICLE 213 WARNING! (Continued) CAUTION! (Continued) • Your vehicle has been built with improved fluids have the knowledge and the proper equipment. If that protect the performance and durability of you have any doubt about your ability to perform a your vehicle and also allow extended mainte- service job, take your vehicle to a competent me- nance intervals.
Page 216 214 MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground, NOTE: The actual interval for changing the oil and and has sat overnight, will improve the accuracy of the replacing the engine oil filter depends on the vehicle oil level readings.
Page 217: Engine Oil Filter
MAINTAINING YOUR VEHICLE 215 Materials Added To Engine Oil assure most efficient service. MOPAR engine oil filters are high quality oil filters and are recommended. The manufacturer strongly recommends against the addition of any additives (other than leak detection Engine Air Cleaner Filter dyes) to the engine oil.
Page 218: Engine Cover
216 MAINTAINING YOUR VEHICLE Engine Cover WARNING! To avoid possible damage to the engine cover, please • Battery fluid is a corrosive acid solution and can disconnect each of the four mounting studs by pulling burn or even blind you. Do not allow battery the engine cover upward, and then lift off the complete fluid to contact your eyes, skin, or clothing.
Page 219: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 217 NOTE: CAUTION! • Use only refrigerants and compressor lubricants ap- • It is essential when replacing the cables on the proved by the manufacturer for your air conditioning battery that the positive cable is attached to the system.
Page 220: Body Lubrication
218 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling HFO 1234yf Particular attention should also be given to hood latch- ing components to ensure proper function. When per- HFO 1234yf Air Conditioning Refrigerant is a hydro- forming other underhood services, the hood latch, fluorocarbon (HFC) that is endorsed by the Environ- release mechanism and safety catch should be cleaned mental Protection Agency and is an ozone-saving prod-...
Page 221 MAINTAINING YOUR VEHICLE 219 to avoid damaging the blade. Keep the wiper blade out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines, or wet spots.
Page 222: Windshield Washer Nozzles
220 MAINTAINING YOUR VEHICLE NOTE: The previous operation can be repeated up to three times. In order to move the blades to the most suitable position. 4. Lift the blade from the windshield and proceed with the required operation. 5. Carefully lower the blade, bringing it back in contact with the windshield.
Page 223: Adding Washer Solvent
MAINTAINING YOUR VEHICLE 221 If there is not a jet of fluid, first check that there is fluid 1. To avoid any interference during the procedure, lift in the washer reservoir. Refer to “Adding Washer the windshield wiper blade. Solvent” in this section for further information. 2.
Page 224 222 MAINTAINING YOUR VEHICLE 5. After the check, reinsert the plug with the control pipe in the initial position. 6. Reposition the washer solvent protection panel and tighten the four self-tapping screws. If the level is not sufficient, namely if there is no washer solvent inside the pipe, proceed as follows: 1.
Page 225: Exhaust System
MAINTAINING YOUR VEHICLE 223 WARNING! Commercially available windshield washer sol- vents are flammable. They could ignite and burn you. Care must be exercised when filling or work- ing around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ex- haust system.
Page 226 224 MAINTAINING YOUR VEHICLE WARNING! CAUTION! (Continued) • Damage to the catalytic converter can result if • Exhaust gases can injure or kill. They contain your vehicle is not kept in proper operating carbon monoxide (CO), which is colorless and condition.
Page 227: Cooling System
MAINTAINING YOUR VEHICLE 225 To minimize the possibility of catalytic converter dam- WARNING! (Continued) age: to cool. Never open a cooling system pressure cap • Do not shut off the engine or interrupt the ignition, when the radiator or coolant bottle is hot. when the transmission is in gear and the vehicle is in •...
Page 228 226 MAINTAINING YOUR VEHICLE flushed and refilled with fresh engine coolant (anti- CAUTION! freeze). Check the front of the A/C condenser for any • Mixing of engine coolant (antifreeze) other than accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically specified Organic Additive Technology (OAT) down the face of the condenser.
Page 229 MAINTAINING YOUR VEHICLE 227 Adding Coolant that meets the requirements of FCA Material Stan- dard MS.90032 and distilled water. Use higher con- Your vehicle has been built with an improved engine centrations (not to exceed 70%) if temperatures below coolant (OAT coolant conforming to MS.90032) that −34°F (−37°C) are anticipated.
Page 230 228 MAINTAINING YOUR VEHICLE If HOAT and OAT coolant are mixed in an emer- WARNING! (Continued) gency, have a authorized dealer drain, flush, and • Do not use a pressure cap other than the one refill with OAT coolant (conforming to MS.90032) as specified for your vehicle.
Page 231: Brake System
MAINTAINING YOUR VEHICLE 229 • Maintain engine coolant (antifreeze) concentration at When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the a minimum of 50% OAT coolant (conforming to coolant bottle. Do not overfill. MS.90032) and distilled water for proper corrosion protection of your engine which contains aluminum Points To Remember...
Page 232 230 MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid. WARNING! Refer to “Fluids, Lubricants, And Genuine Parts” in “Maintaining Your Vehicle” for further information. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting WARNING! or riding on the brake pedal can result in abnor- mally high brake temperatures, excessive lining...
Page 233 MAINTAINING YOUR VEHICLE 231 Checking Brake Fluid WARNING! (Continued) • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces.
Page 234 232 MAINTAINING YOUR VEHICLE To check the brake fluid level, proceed as follows: Adding Brake Fluid 1. Loosen the two screws and remove the brake fluid If the fluid level in the reservoir is not sufficient, protection panel. proceed as follows: 1.
Page 235: Alfa Twin Clutch Transmission
MAINTAINING YOUR VEHICLE 233 5. Reposition the brake fluid protection panel and Special Additives tighten the two screws. The manufacturer strongly recommends against using any special additives in the transmission. NOTE: Be very careful while removing the plug from the opening to prevent the plug from falling inside the Transmission fluid is an engineered product and its vehicle body.
Page 236: Appearance Care And Protection From
234 MAINTAINING YOUR VEHICLE you notice fluid leakage or transmission malfunction, hot or cold weather and other extreme conditions will visit your authorized dealer immediately to have the have an adverse effect on paint, metal trim, and under- transmission fluid level checked. Operating the vehicle body protection.
Page 237 MAINTAINING YOUR VEHICLE 235 • If insects, tar, or other similar deposits have accumu- CAUTION! (Continued) lated on your vehicle, use MOPAR Super Kleen Bug • If the engine compartment is washed with an and Tar Remover to remove. high pressure jet, keep it at a distance of at least 8 •...
Page 238 236 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertiliz- NOTE: Many aftermarket wheel cleaners contain strong ers, de-icer salt, etc., be sure that such materials are acids or strong alkaline additives that can harm the well packaged and sealed.
Page 239 MAINTAINING YOUR VEHICLE 237 CAUTION! CAUTION! (Continued) Warranty. USE ONLY MILD SOAP AND WATER Do not use scouring pads, steel wool, a bristle WITH A SOFT CLOTH. Used on a regular basis; brush, metal polishes or oven cleaner. These prod- this is all that is required to maintain this finish.
Page 240 238 MAINTAINING YOUR VEHICLE Interior Care CAUTION! Use MOPAR Total Clean to clean fabric upholstery and • Direct contact of air fresheners, insect repellents, carpeting. suntan lotions, or hand sanitizers to the plastic, Use MOPAR Total Clean to clean vinyl upholstery. painted, or decorated surfaces of the interior may cause permanent damage.
Page 241 MAINTAINING YOUR VEHICLE 239 Do not use abrasive cleaning components, solvents, Instrument Panel Bezels steel wool or other aggressive material to clean the lenses. CAUTION! Glass Surfaces When installing hanging air fresheners in your vehicle, read the installation instructions carefully. All glass surfaces should be cleaned on a regular basis Some air fresheners will damage the finish of with MOPAR, or any commercial household-type glass...
Page 242: Fuses
240 MAINTAINING YOUR VEHICLE Seat Belt Maintenance FUSES Do not bleach, dye or clean the belts with chemical WARNING! solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. • When replacing a blown fuse, always use an appropriate replacement fuse with the same amp If the belts need cleaning, use a mild soap solution or rating as the original fuse.
Page 243: Engine Compartment Fuses
MAINTAINING YOUR VEHICLE 241 Engine Compartment Fuses The ID number of the electrical component correspond- ing to each fuse can be found on the back of the cover. The engine compartment fuse box is located on the left side of the engine compartment, next to the battery. To access the fuses, remove screws, and then remove the cover.
Page 244 242 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Mini Fuse Description 70 Amp Tan – Body Controller 20 Amp Yellow – Ignition Switch 40 Amp Orange – Anti-Lock Brake Pump 20 Amp Yellow – Anti-Lock Brake Valve 40 Amp Orange – Radiator Fan - Low Speed 50 Amp Red –...
Page 245: Dashboard Fuse Box
MAINTAINING YOUR VEHICLE 243 Cavity Maxi Fuse Mini Fuse Description – 10 Amp Red Water Pump, HVAC 30 Amp Green – Headlamp Washer – If Equipped 40 Amp Orange – Alfa Twin Clutch Transmission Pump – 5 Amp Tan After Run Pump –...
Page 246: Vehicle Storage
244 MAINTAINING YOUR VEHICLE Vehicle Fuse Num- Cavity Mini Fuse Description 7.5 Amp Brown Stop Light Switch, Instrument Panel Node 5 Amp Tan Transmission Shifter Module, Cigar Lighter Light, Drive Style Unit, Heated Mirrors Relay 5 Amp Tan Climate Control, Body Controller 20 Amp Yellow Driver Power Window VEHICLE STORAGE...
Page 247: Bulb Replacement
MAINTAINING YOUR VEHICLE 245 Bulb Number Bulb Number Dipped/Main Beam HIR2 NOTE: Numbers refer to commercial bulb types Headlights (Versions that can be purchased from your authorized dealer. With Bi-Halogen Head- If a bulb needs to be replaced, visit your authorized lights) —...
Page 248: Front Light Clusters
246 MAINTAINING YOUR VEHICLE Front Light Clusters Side Lights/Daytime Running Lights (DRL) The front head lamp contains bulbs for the parking These are LEDs. For the replacement, contact the your lights/daytime running lights (DRL), low beam head- authorized dealer. lights, high beam headlights and direction indicators. Low/High Beam Bi-Halogen Headlights To change the bulb, proceed as follows: 1.
Page 249 MAINTAINING YOUR VEHICLE 247 3. Remove protective cover from headlamp assembly. 1 — Electrical Connector Protective Cover 2 — Bulb Holder 4. Remove the electric connector (1) and then rotate the 5. Extract the bulb and replace it. bulb holder (2) clockwise and remove it. 6.
Page 250 248 MAINTAINING YOUR VEHICLE Direction Indicators Front: 1. Turn the steering wheel completely. 2. Open the protective flap by rotating the screw. Protective Cover 4. Rotate the bulb holder counterclockwise and remove 5. Rotate the bulb assembly counter clockwise to re- move from bulb holder.
Page 251: Front Side Marker
MAINTAINING YOUR VEHICLE 249 Side: Front Side Marker To change the bulb, proceed as follows: 1. Adjust the lens in the point shown in to compress the retaining clip, then pull the cluster outwards. 1. Turn the front wheels to gain access and then remove the fastener from the inner wheel liner.
Page 252: Rear Light Clusters
250 MAINTAINING YOUR VEHICLE 2. Fold back wheel liner door to access bulb housing. Front Side Marker Bulb Rear Light Clusters Bulb Housing Location 3. Remove bulb from bulb housing then remove and These contain the bulbs for the side lights, direction replace bulb and reinstall.
Page 253: Tail Lights/Brake Lights
MAINTAINING YOUR VEHICLE 251 First Protective Cap Second Protective Cap 2. Remove the second protective cap insert a hand 3. Rotate clockwise to remove the bulb holder remove inside the opening. the bulb from the bulb holder. 4. Install the bulb by pressing it into bulb holder then turn install the bulb holder and turn it counterclock- wise.
Page 254: Reversing Light
252 MAINTAINING YOUR VEHICLE Reversing Light WARNING! The reversing light are located close to the exhaust pipes; take the utmost care not to get burnt during the bulb replacement. To replace the reversing lights, turn the bulb holder counterclockwise, remove the bulb and replace it. Reversing Light Bulb Holder Third Brake Lights These are LEDs.
Page 255: License Plate Lights
MAINTAINING YOUR VEHICLE 253 License Plate Lights 2. Turn bulb holder (1) counterclockwise, remove bulb (2) and replace it. To replace the bulbs proceed as follows: 1. Position the lens in the point shown laterally to compress the retaining clip, then pull the license plate light cluster out.
Page 256: Roof Light
254 MAINTAINING YOUR VEHICLE Roof Light 2. Open protective flap (2) and replace bulb (1), releas- ing it from the side contacts. Make sure that the new To change the bulb, proceed as follows: bulb is correctly secured between the contacts. 1.
Page 257: Luggage Compartment Roof Light
MAINTAINING YOUR VEHICLE 255 Luggage Compartment Roof Light 2. Open light protector (2) and replace the bulb. To replace the bulb, proceed as follows: 3. Close protector on the lens. 1. Open the luggage compartment and remove luggage 4. Install luggage compartment roof light by inserting it compartment roof light, working in the direction in its correct position, first on one side and then shown by the arrow.
Page 258: Fluid Capacities
256 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 1750 Turbo Engine 10.5 Gallons 40 Liters Reserve Fuel 1.1 Gallons 4 Liters Engine Oil with Filter 1750 Turbo Engine 6.1 Quarts 5.8 Liters Cooling System 1750 Turbo Engine (MOPAR 11.2 Quarts 10.6 Liters Antifreeze/Engine Coolant 10...
Page 259 MAINTAINING YOUR VEHICLE 257 Component Fluid, Lubricant, or Genuine Part Engine Oil – 1750 Turbo Engine We recommend you use SAE 5W-40 API Certified Synthetic Engine Oil, meeting the requirements of FCA Material Standard MS-12991. Engine Oil Filter – 1750 Turbo Engine We recommend you use MOPAR Engine Oil Filter.
Page 260: Chassis
258 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part • Gearbox: Full synthetic 75W-85 manual transmission fluid meeting Alfa Twin Clutch Transmission MS.90021 or FPW9.55550–MZ3 or the API GL4 specification. • Control System: Use only MOPAR C Series DDCT SAE 75W Hydrau- lic Fluid or equivalent.
Page 261 MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart ....262 MAINTENANCE SCHEDULE ... .260...
Page 262 260 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE NOTE: The actual interval for changing the oil and replacing the engine oil filter depends on the vehicle Your vehicle is equipped with an automatic oil change usage conditions and is signalled by the warning light indicator system.
Page 263 MAINTENANCE SCHEDULES 261 • Check front and rear disc brake pad condition and If the vehicle is operated in a dusty or dirty environ- wear. ment the engine air filter has to be changed every 6,500 miles (10,000 km). • Check cleanliness of tailgate locks. Once A Month Or Before A Long Trip/Periodic •...
Page 264 262 MAINTENANCE SCHEDULES Maintenance Chart At Every Oil Change Interval As Indicated By Oil Change Indicator System: Required Maintenance Intervals Inspect brake pads, shoes, rotors, drums, and hoses. Refer to the maintenance schedules on the following Inspect engine cooling system protection and hoses. page for the required maintenance intervals.
Page 265 MAINTENANCE SCHEDULES 263 Mileage or time passed (whichever comes first) Or Months: Or Kilometers: Check lighting system op- eration (headlights, direc- tion indicators, hazard lights, passenger compart- ment lights, boot lights, instrument panel warning lights, etc.) Check vehicle fasteners Check mechanical compo- nents fasteners Check windshield/washer operation...
Page 266 264 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Months: Or Kilometers: Visually inspect condition of: exterior bodywork, car- bon monocoque, aerody- namic bottom, pipes and hoses (exhaust, fuel sup- ply system, brakes), rub- ber elements (boots, drive- shaft boots, sleeves, bushes, etc.) Check condition and wear...
Page 267 MAINTENANCE SCHEDULES 265 Mileage or time passed (whichever comes first) Or Months: Or Kilometers: Check and top off, if re- quired, fluid levels (engine coolant, brake/hydraulic clutch fluid, windscreen washer fluid, battery fluid, etc) Visually inspect the condi- tion of accessory drive belt(s) Check condition of timing belt...
Page 268 266 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Months: Or Kilometers: Replace accessory drive belt(s) Replace spark plugs * Replace toothed timing drive belt ** Change engine oil and oil filter *** Change brake fluid every 24 months***** Replace air filter car- tridge**** •...
Page 269 MAINTENANCE SCHEDULES 267 • Contact your Alfa Romeo Dealer if you have ques- WARNING! tions. • You can be badly injured working on or around a ** Regardless of the distance covered, the timing belt motor vehicle. Do only service work for which must be changed every four years for particularly you have the knowledge and the right equipment.
Page 271: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... .270 Impaired (TDD/TTY).
Page 272: Suggestions For Obtaining Service For Your Vehicle
270 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be Prepare For The Appointment happy with our products and services. If you are having warranty work done, be sure to bring the right papers with you, as well as your warranty Warranty service must be done by an authorized dealer.
Page 273: Alfa Customer Center
IF YOU NEED CONSUMER ASSISTANCE 271 Any communication to the manufacturer’s customer (TTY) in the United States, can communicate with the center should include the following information: manufacturer by dialing 1-800-380-CHRY. • Owner’s name and address Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered •...
Page 274: Warranty Information
272 IF YOU NEED CONSUMER ASSISTANCE service contract that is not a manufacturer’s service WARRANTY INFORMATION contract, and you require service after the manufactur- See the Warranty Information Booklet, located on the er’s New Vehicle Limited Warranty expires, please refer USB card, for the terms and provisions of ALFA RO- to the contract documents, and contact the person listed MEO Automobiles warranties applicable to this vehicle...
Page 275: In Canada
IF YOU NEED CONSUMER ASSISTANCE 273 SE., West Building, Washington, D.C. 20590. You can Service Manuals also obtain other information about motor vehicle These comprehensive Service Manuals provide the in- safety from http://www.safercar.gov. formation that students and professional technicians In Canada need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing FCA US LLC If you believe that your vehicle has a safety defect,...
Page 276 274 IF YOU NEED CONSUMER ASSISTANCE Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA US LLC vehicles. In- cluded are starting, operating, emergency and mainte- nance procedures as well as specifications, capabilities and safety tips.
Page 277 INDEX...
Page 278 276 INDEX Adding Engine Coolant (Antifreeze) ...227 Antifreeze (Engine Coolant)....226, 256 Adding Fuel ......187 Capacities .
Page 279 INDEX 277 Warning Light ......93 Cleaning Break-In Recommendations, New Vehicle ..55 Wheels .
Page 280 278 INDEX Deck Lid, Release ......68 Emission Control System Maintenance ..211 Defroster, Windshield .
Page 281 INDEX 279 Exterior Lights ......59 Octane Rating ......183 Requirements .
Page 282 280 INDEX Ignition ....... . .9 Key, Sentry (Immobilizer) ....11 Key .
Page 283 INDEX 281 Turn Signal ......59, 106 Rearview ......63 Warning (Instrument Cluster Description) .
Page 284 282 INDEX Operating Precautions .....210 Reformulated Gasoline ....184 Operator Manual (Owner’s Manual) .
Page 285 INDEX 283 Lap/Shoulder Belt Operation ....29 Service Manuals ......273 Lap/Shoulder Belts .
Page 286 284 INDEX Tire And Loading Information Placard ..162, 163 To Open Deck Lid ......68 Tire Markings .
Page 287 INDEX 285 Vehicle Security Alarm (Security Alarm) ..12 Vehicle Storage ......244 Warning Flasher, Hazard .
Page 288 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.

Alfa Romeo 4C 2017 Owner's Manual

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

If You Need Consumer Assistance

Quick Links

Chapters

Related Manuals for Alfa Romeo 4C 2017

Summary of Contents for Alfa Romeo 4C 2017