Audiovox Pursuit PRO-9900 Owner's Manual

Pursuit series remote start security system with plug-in shock sensor & starter disable

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

4 Button Remote Start Security System With

Plug-In Shock Sensor & Starter Disable

IMPORTANT ! In order to provide you with the highest level of security to your

vehicle, this system is equipped with selectable manual override circuitry. It is

possible that you will need to override you security system if the transmitter

becomes lost, or inoperative due to battery failure. Reading the sections on

"Manually Overriding Your System" is necessary to fully understand the procedure

required to enable your vehicle in such situations. In addition, the chart on the last

page of this manual has a section for the particular features and options installed

in your vehicle as well as the override method selected. Although the default

mode is "Valet Switch" operation, the system can be configured for "Custom

Code" operation for enhanced security. Confirm the override mode selected on

the last page of this manual, and familiarize yourself with the section on it's opera-

tion.

FEATURES :

! 1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control

! Six Channel Code Learning Programmable Receiver

! External Superheterodyne Transceiver Antenna

! Single Or Two User Programmable W/Separate Control Outputs

! Single Button Lock/Unlock or Separate Button Lock/Unlock or Both

! Remote Keyless Entry With Optional Access Guard (must have power door

locks)

! Selectable Manual Override Mode

! New Enhanced Panic Feature (Any button other than unlock stops siren, no

change to the units state)

! Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )

! Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect

Off, City Mode)

! Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or

For R/S)

! 24 Hour Time Start Mode

! Cold Temperature Start Mode

! 2 or 4 Hour Automatic Start Mode

! Parking Meter Count Down Timer On LCD Remote

! Additional Count Down Timer Mode

! Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds

To Engage)

! Improved Custom Code Override, User Selectable and Programmable

Model PRO-9900

Owner's Manual

Page 1

128-7398

1 of 24

Table of Contents

Summary of Contents for Audiovox Pursuit PRO-9900

Page 1 ! Additional Count Down Timer Mode ! Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds To Engage) ! Improved Custom Code Override, User Selectable and Programmable Model PRO-9900 Owner’s Manual Page 1 128-7398 1 of 24...
Page 2: Your "Code Hopping" Transmitters
! Protected Push Button Valet/Override Switch ! 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming ! Intrusion Alert With Memory ! Instant Siren Activation ! Starter Disable Output ! Additional Engine Immobilizer Output, (Optional Relay Required) ! True Last Door Arming (Hardwire Only) ! Defective Zone By-Pass ! Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)
Page 3: Arming The System - Active
known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system. Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then re-transmits your signal, the alarm system will not respond.
Page 4: Arming The System - Passive (Automatic)
" The dash mounted LED begins to flash slowly. " Parking Lights flash one time. " Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired.
Page 5: Disarming The System
started. " Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. " Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle.
Page 6: While The System Is Sounding
automatically. Open any door to suspend the automatic arming. " Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered.
Page 7: Programming Your Custom Override Code
LED turns on solid. The system will remain in the valet mode. 3. To return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE: Always remember to return the system to normal operation. This will ensure that the vehicle remains protected at all times.
Page 8: Eliminating The Normal Arm / Disarm Chirps
Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3.
Page 9: Remote Panic Operation
1. Turn the ignition key on then off. 2. Within 10 seconds, press and release valet switch three times. 3. If the chirps were on before you started, then you will hear two chirps indicat- ing they have been turned off. If the chirps were off before you started, then you will hear one chirp indicating they have been turned on.
Page 10: Remote Starting The Vehicle
In this mode, the pre-detect chirps will change from six pre-warning tones to a full 10 seconds of warning chirps. The full detect trigger duration will be reduced from 30 seconds to 15 seconds. NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only.
Page 11: Operating On Automatic Start Up Timer Mode
monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged. To Remote Start The Vehicle: Press and release the programmed channel of your keychain transmitter two times within 2 seconds. The vehicle will start and remain running for the pre- programmed 5, 10, 15, or 20 minutes.
Page 12 The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. CANCELING THE AUTOMATIC START UP TIMER To cancel the automatic start up timer do one of the following; 1. Start the vehicle manually with the use of the ignition key and depress the brake pedal.
Page 13: Turbo Timer Mode
Some of the more common uses for this channel are: # Remote Car Starter # Remote Window Closure # Remote Garage Door Interface To remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. ADDITIONAL REMOTE FUNCTION ( CHANNEL 6 ) Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter, or by and independent button or combination of buttons.
Page 14: Telematic Upgrade
set up for turbo timer during installation. Consult with your installation center to be certain this feature was activated and how long the vehicle will continue to run, 3, 5, or 10 minutes after the ignition switch is turned off. To activate the turbo timer: Anytime the engine is running for more than 15 seconds: 1) Place the gear selector in park.
Page 15 unit shuts off the exhaust indication will turn off and the trans- mitter will play a melody. If text mode was selected, the screen will scroll the words Engine Running. Note Engine can be started in many modes armed, disarmed, valet, etc...
Page 16 When the vehicle is armed, and a door is opened, or ajar, the transmitter will chirp 3 times, the lights will flash, and the display will indicate a door trigger as shown on the previous page. In the text mode the word Armed, Door Opened will appear.
Page 17 ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below: NOTE: Transmitter must be within operating range of the vehicle, approximately 1000 ft.
Page 18 the transmitter will emit a tone confirming the feature is active. Note: the unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide.
Page 19 NOTE: Your system is shipped with two transmitters, 1 two way, shown on the left and the one way transmitter, shown right. The one and two way transmitters are programmed from the factory with separate lock & unlock buttons, the trunk/ key icon button operates remote start and remote trunk release where applicable.
Page 20 (i) You can set the unit to provide a Tone, or Vibrate upon activation (j) You can set the Countdown Timer (k) You can set the Alarm Clock (l) You can set the Clock Your transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left.
Page 21 Throughout this manual you will find screen shots where they apply if using the two way transmitter. If using the one way transmitter while the two way transmitter is within range of the vehicle, the two way transmitter will update it's screen.
Page 22 THIS PAGE LEFT BLANK INTENTIONALLY Page 22 128-7398 22 of 24...
Page 23 3 CHIRPS 4 CHIRPS * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH 2 FLASHES 3 FLASHES PRO-9900 PASSIVE ARMING/ACTIVE ARMED DISARMED VALET MODE INTRUSION ZONE 3 INTRUSION ZONE 2 INTRUSION ZONE 1...

Audiovox Pursuit PRO-9900 Owner's Manual

Quick Links

Related Manuals for Audiovox Pursuit PRO-9900

Summary of Contents for Audiovox Pursuit PRO-9900

Table of Contents