Advertisement
To Charge/Recharge
• Use only the Charging Base
may range to 240V AC. Your
provided.
new Trimmer Charging Base
may be used with voltage
• (Re)charge at tempera-
ranging from 110-130V AC
tures between 40˚F and
only.
95˚F. Charging at lower or
higher temperatures
1. Be certain Trimmer is OFF
adversely affects lifetime
(Fig. 1).
of battery.
2. Charge the Trimmer in the
• Charging requires a full
Charging Base.
10 hours.
3. Plug the cord of Charging
• Recharging longer than
Base into the electrical
the required period of time
outlet.
will not harm Trimmer.
4. Green Charging Indicator
However, continuously
Light will light to indicate
charging Trimmer will
Trimmer is (re)charging
reduce life of battery.
(Fig. 2).
VOLTAGE
In North America, Central
America, and South America,
the most common voltage is
between 110 and 130V AC.
When traveling to other
countries, common voltage
1
2
9
8
7
6
5
4
3
2
1
Hair Length Selector
NOTE:
• Trimmer Guard
Attachment must be in
1. The Charging Base can
place on the Trimmer in
also be used to store the
order to use the Zoom
Trimmer.
Ring.
2. In order to ensure the
• Zoom Ring with Trimmer
longest possible working
Guard Attachment ensures
life of the battery:
precise trimming and has
• Do not charge for more
9 adjustable settings (see
than 24 hours.
chart below).
• Do not keep the Charging
• Zoom Ring will "click" into
Base permanently plugged
position at each setting.
in.
#1
Stubble Length or Closely Cropped
• Plug in the Charging Base
#2
Short
only when you hear the
sound indicating the
#3
rechargeable battery will
#4
be empty soon.
#5
Medium
• Discharge the battery
#6
completely once a year
#7
by letting the motor run
#8
until it stops.
#9
Long
3. If the battery is empty and
you want to trim your
beard, charge Trimmer for
at least 1.5 hours and you
3
will have enough power
for one use.
4. If the Trimmer hasn't
been used for a long
period of time, Trimmer
must be recharged for a
full 10 hours.
Trimmer Guard Attachment
• Start at a longer setting
To Remove
(#7, 8 or 9) to prevent
Remove Trimmer Guard
accidentally trimming
Attachment if you are:
hairs too short (Fig. 3).
• Defining hair lines
• Trim against the direction
• Trimming nape of neck
of hair growth (Fig. 4)
• Removing single, unwanted
• As you become familiar
hairs
with the settings, adjust
1. Be certain Trimmer is in the
Zoom Ring to desired
OFF position.
trimming length.
2. Hold Trimmer Base with
one hand, grasp sides of
Trimmer Guard Attachment
.06 in./1.5 mm
and gently slide Attachment
off Trimmer (Fig. 5).
.1 in./2.5 mm
.16 in./4 mm
NOTE: Zoom Ring can be
on any setting when remov-
.22 in./5.5 mm
ing or replacing Trimmer
.3 in./7.5 mm
Guard Attachment.
.38 in./9.5 mm
To Replace
.48 in./12 mm
1. Be certain Trimmer is in the
.6 in./15 mm
OFF position.
.72 in./18 mm
2. Hold Trimmer in one hand
and replace Attachment
4
5
9
8
7
6
back onto Trimmer until it
the desired amount of hair.
"clicks" into position.
To Trim Outer Edge of Beard
NOTE: The Trimmer Guard
& Add Definition
Attachment can be placed
1. Remove Trimmer Guard
on Trimmer only one way.
Attachment.
If it does not fit properly,
reverse it.
2. Hold Trimmer diagonally
with front of Trimmer facing
To Trim Beard
away from you (Fig. 7).
1. Comb hairs outward so that
3. Turn Trimmer ON.
they are at their maximum
height and in the same
4. Start at chin and work back
direction.
toward ear.
2. With Trimmer Guard
5. Follow line of jawbone to
Attachment in place,
cut away longer hairs on
set Zoom Ring to desired
outer edge of beard.
setting.
6. Turn Trimmer OFF.
3. Slide ON/OFF switch to the
NOTE: Practice is best for
ON position and begin trim-
optimum results.
ming (Fig. 6).
To Define Beard Line
4. Turn Trimmer OFF.
1. Hold Trimmer vertically
IMPORTANT: If using Trimmer
with front of Trimmer fac-
without Trimmer Guard
ing you.
Attachment, use a slow, very
2. Start with trimmed edge of
light "skimming" technique to
beard and with downward
prevent trimming off more than
6
7
Advertisement
