Error Message Displays - Panasonic AJ-D200P Operating Instructions Manual

Error
messages which appear
during operation
Error display
Cause
Remedial action
TOO
BRIGHT
ERROR
This appears
when
the white balance
is
to
be
adjusted
(when the
AUTO
W/B BAL
switch
was
operated) or
when
the
screen
is
excessively
bright.
Stop
down
the
iris
a
little
more,
and
adjust
the
white balance.
If
the error display remains,
insert
the
electronic shutter
or attach the
ND
filter.
TOO DARK ERROR
This
appears
when
the white
balance
is
to
be
adjusted
(when
the
AUTO
W/B BAL
switch
was
operated) or
when
the
screen
is
excessively
dark.
Open
the
iris
a
little
more, increase
the gain
(if
this
is
warranted by
the subject brightness),
and
adjust the white balance.
If
the error display
remains,
direct
some
light
onto the
subject.
LENS UNIT
ERROR
This
appears
when
the lens cable
has been
disconnected or
when
the lens
iris
control circuit
has been damaged.
The cause
is
almost always a
disconnected
lens
cable.
If
the
display
appears even when
the
cable
is
connected
properly, consult with your
dealer.
SELECT
SW
ERROR
This appears
when
the
AUTO
W/B BAL
switch
was
operated with the white balance selector
switch
at
a
position
other than
MEMO.
Adjust the white balance (operate the
AUTO
W/B BAL
switch) with the white balance
selector
switch at
the
MEMO
position.
OUTPUT
SW
ERROR
This appears
when
the
AUTO
W/B BAL
switch
was
operated with the
OUTPUT
switch
at
a
position
other than
CAM.
Adjust the white balance (operate the
AUTO
W/B BAL
switch) with the
OUTPUT
switch
at
the
CAM
position.
BLACK BAL
ERROR
This
points to
a malfunction
in
the
camera
unit.
Consult
with your dealer.
WHITE BAL
ERROR
TRY AGAIN
This
appears
when
the white balance
was
not
attained
properly due
to
some
condition or
other.
If
the
TOOL
BRIGHT ERROR,
TOO DARK
ERROR
or
LENS
UNIT
ERROR
message
has
appeared,
take the corresponding
measure, and
then
try
adjusting the white balance
again.
If
the
WHITE
BAL
ERROR
TRY
AGAIN
message
has appeared
but the
TOOL
BRIGHT
ERROR,
TOO DARK ERROR
or
LENS
UNIT
ERROR
message
has
not
appeared, proceed
to
attain
the white balance again.
If
the display
still
appears even
after
two
or
three
attempts,
consult with your
dealer.
Remarks:
The above
errors
are detected
when
the white balance
is
adjusted
(when
the
AUTO
W/B BAL
switch
has been
operated).
The
LENS
UNIT
ERROR
is
also
detected immediately
after
the
power has been
switched
on.
SERVO
This
appears
when
an unrecorded
part of
a tape
is
played
back
or at other times
when
the
VTR
servo
lock
is
disengaged.
It
is
normal
for this
display
to
appear
with
unrecorded
parts
of
tapes.
If
the display
appears during the playback
of
an
obviously
recorded tape
or during recording,
this points
to
a malfunction. Consult
with
your
dealer.
HUMID
This
signifies
that
condensation has
formed.
Refer
to
page 63 where
detailed instructions
can be
found.
Refer
to
page 63 where
detailed instructions
can be
found.
POWER
OFF
This
is
not
an
error
message.
It
is
a
warning which
indicates that the
power
will
be
turned
off
very
shortly.
17