: Silver Nano Health System and Deodorizing/ Catechin Filter are adopted. Silence Mode : When you use the "Silence Mode", you can experience extremely quiet operation of your air conditioner. AQV18FAX, AQV24FAX, AQV24FAXXSA For more information, Please access to our service web site(http://itself.sec.samsung.co.kr)
5-3 Ass’y Control In ..........................5-4 Ass’y Control Out ..........................16. Electrical Parts List ........................17. Wiring Diagram ..........................7-1 Indoor Unit ............................7-2 Outdoor Unit ............................ 18. Schematic Diagram ........................8-1 Indoor Unit ............................8-2 Outdoor Unit ............................ Samsung Electronics...
Page 3
14-2 Low Refrigerant Pressure Distribution 14-2 ..................14-3 Pressure & Capacity mark 14-3 ......................14-4 Q & A for Non-trouble 14-4 ........................14-5 Cleaning/Filter Change 14-7 ......................... 14-6 Installation 14-9 ............................14-7 Installation Diagram of Indoor Unit and Outdoor Unit 14-10 ............Samsung Electronics...
Good Morning Mode can help you sleep quickly and soundly and wake up refreshed. Multi functional cleaning system With Silver Nano Health System and Deodorizing/Catechin Filters makes your room more refreshed. Silence Mode When you use the “Silence Mode”, you can experience extremely quiet operation of your air conditioner. Samsung Electronics...
880 x 638 x 310(mm³) Indoor Unit 48dB↓ 48dB↓ Noise Outdoor Unit 58dB↓ 60dB↓ Silver Nano Evaporator Silver Nano Evaporator Air Purifying System Filter Catechin Filter Catechin Filter Deodorizing Fiter Deodorizing Fiter Indoor Display Three Color LED Display Three Color LED Display Samsung Electronics...
3) Loosen 1 of the right screw(CCW) and detach the Terminal Cover. (Use +Screw Driver.) 4) Detach the thermistor from the Front Grille. 5) Loosen 2 fixing screws(CCW) of Front Grille. 6) Unlock 3 hooks to fix Panel Front and Tray Drain. (Use +Screw Driver.) Samsung Electronics...
Page 22
2) Detach the outdoor unit connection wire from the Terminal Block. 3) Loosen 4 fixing screws(CCW) of Ass'y Control-In. (Use +Screw Driver.) You can disassembly Ass'y Control In without evaporator disassembled. Tray Drain 1) Pull Tray Drain out from the Back Body. Samsung Electronics...
Page 23
Evaporator from indoor unit. Fan Motor 1) Loosen the fixing screw(CCW). & (Use +Screw Driver.) Cross Fan 2) Detach the Fan Motor from the Fan. 3) Detach the Fan From the left Holder Bearing. Samsung Electronics...
1) Loosen 1 fixing screw(CCW) of the Cover- Control and detach the Cover Control. 2) Loosen fixing screws(CCW) and detach the Cabinet-Upper. 3) Loosen 1 screw(CCW) fixed to assemble Control Box with Cabinet-Side RH. 4) Loosen 6 fixing screws(CCW) and detach the Cabinet-Side RH. Samsung Electronics...
Page 25
Disassembly and Reassembly Parts Procedure Remark 5) Loosen 2 screws(CCW) fixed on the Guide Condenser. 6) Loosen fixing screws(CCW) of the Cabinet Front. Samsung Electronics...
Page 26
Motor 2) Detach the Fan Propeller. 3) Loosen 4 fixing screws(CCW) to detach the Motor. 4) Disconnect the wire between Ass’y Control Out and Motor. 5) Loosen 2 fixing screws(CCW) and detach the Bracket Motor. Samsung Electronics...
Page 27
Compressor 1) Loosen the fixing nut(CCW) and detach the Compressor Lead Wire. 2) Disassemble the Felt Comp Sound. 3) Loosen the 3 bolts(CCW) at the bottom of Compressor like the picture on the right side. Samsung Electronics...
The compressor operates in a reverse cycle to remove Indoor fan and outdoor fan stop operation intermittently exterior ice in a HEAT mode, and indoor fan and outdoor in a HEAT mode. fan do not operate intermittently for within 20% of the total heater operation 12-1 Samsung Electronics...
Replace fuse FUSE(F701) : T3.15[A]/250[V] Check the output of SMPS on the control board. Input power: AC230±15%[V] PCB should be replaced IC02 Input: DC12[V] IC02 output: DC5[V] Check the setting temperature Samsung Electronics 12-2...
Page 31
Is there no error at the insertion of PCB? Exchange the PCB. Exchange the PCB. Are the BLDC FAN Wire Is the +,- of C102 short? 1 and 3 short? Exchange the PCB. Exchange the BLDC FAN. Normal Operation Exit 12-3 Samsung Electronics...
Page 32
Voltage at pin #30~#34 of micom (IC04) Micom (IC04) is faulty. change?(Squarewave) Voltage at Driver IC05/06 (ULN2003A) is faulty. pin #2 ~ #5 of CN61(motor connector) change?(Squarewave) Up/Down louver motor is faulty. Samsung Electronics 12-4...
Page 33
Pull out the power cord and during the operation?(Square-Wave) execute the following step after 30 seconds. Disassemble the BLDC FAN Wire. Is the short between Exchange the PCB. the BLDC FAN Wires? Exchange the BLDC FAN MOTOR. Exchange the PCB. 12-5 Samsung Electronics...
Page 34
Pull out the power cord and exchange the PCB from the case after 30 seconds. Is the assembly of Micom and Exchange the PCB. peripheral circuit part good? Check again after assembly of PCB. Samsung Electronics 12-6...
Page 35
4 way valve coil. Dose the voltage of AC 220V Exchange apply to the connector of 4 way the outdoor PCB. valve coil during the operation? Go to the next page 4 way valve main body error 12-7 Samsung Electronics...
Page 36
Connect the connector. correctly? Check the resistance value Outdoor fan error of outdoor fan. Dose the voltage of DC300V apply to the connector of outdoor Check the motor wire. fan during the operation of outdoor unit? Outdoor PCB error Samsung Electronics 12-8...
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 18.2K? Exchange the PCB. Exchange the PCB. Normal operation Exit 400.0 350.0 300.0 250.0 200.0 150.0 100.0 50.0 12-9 Samsung Electronics...
Page 38
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 24K? Exchange the PCB. Exchange the PCB. Normal operation Exit 600.0 500.0 400.0 300.0 200.0 100.0 Samsung Electronics 12-10...
Page 39
Exchange the sensor. (Refer to the R/T TABLE) Is the resistance value of sensor connection pull_up 18.2K? Exchange the PCB. Exchange the PCB. Normal operation Exit 400.0 350.0 300.0 250.0 200.0 150.0 100.0 50.0 12-11 Samsung Electronics...
Page 40
4) Is the resistance value of sensor connection pull_up correct? 2. Troubleshooting procedure Remove the Fan lock. Isn't the Fan locked? Is the connector connected correctly? Connect the connector. Is the color of Fan wire matched correctly? Exchange the Fan. Exchange the PCB. Normal operation Exit Samsung Electronics 12-12...
Page 41
1, 2 correct after power supply? Is the capacitor(C101, C102, C103) Connect the connector. for DC-Link assembled in accordance the specification? Are R113, R114, R115 470kohm? Exchange the PCB. Is R116 14.3kohm? Exchange the Fan. Exchange the PCB. Normal operation Exit 12-13 Samsung Electronics...
Page 42
Is the position of temperature sensor Correct the sensor position or and the sensing value normal? exchange the sensor. Is the connection cable for Correct the cable connection. the compressor and power terminal normal? Exchange the PCB. Samsung Electronics 12-14...
Correct the wrong wiring. and communication cable error? Is the connection of Correct the connection of communication cable normal? communication cable. Is it the outdoor Exchange the indoor/outdoor unit PCB. 2 Micom(Inverter + Main) model? Exchange the outdoor unit PCB. 12-15 Samsung Electronics...
Page 44
Exchange the compressor. compressor (u↔v, v↔w, w↔u) normal? Is the compressor body and Exchange the compressor. interphase resistance insulated? Is the connection cable for the Correct the cable connection. compressor and power terminal normal? Exchange the PCB. Samsung Electronics 12-16...
Page 45
Exchange the compressor. compressor (u↔v, v↔w, w↔u) normal? Is the compressor body and Exchange the compressor. interphase resistance insulated? Is the connection cable for the Correct the cable connection. compressor and power terminal normal? Exchange the PCB. 12-17 Samsung Electronics...
Page 46
Is the resistance for the Exchange the PCB. detection of DC Link voltage normal? Is the resistance value of Exchange the PCB. DC Link discharge normal? Is the reactor insulation damaged? Exchange the PCB. Exchange the reactor. Samsung Electronics 12-18...
Page 47
12-2-18 The others 1. AC Line Zero Cross Signal OUT – Check the assembly condition of peripheral part of IC21, ZD21, ZD20 and D200 on the PCB. 2. Capacity miss match – Check again the indoor unit option code. 12-19 Samsung Electronics...
2) The fan motor of the indoor unit doesn’t run. • Fan Motor Connector(CN72) is faulty 3) The power voltage between terminal #3 and #5 • ASS’Y Main PCB is faulty of the connector(CN72) is 0V. • Connection is faulty Samsung Electronics 12-20...
Page 49
1) Is CN01 1, 3 over 250V? • Outdoor PCB Error 2) Is CN01 3, 5 within 1V~5V? • BLDC Motor Error 3) Is the voltage of CN01 6 changed? 4) Is the resistance of BLDC Motor 1, 3 opened after power off? 12-21 Samsung Electronics...
∞, 0Ω . . . Open or Short Stepping Motor Measure the resistance between the red wire and each terminal wire with a tester. Normal About 300Ω at the normal temperature (20˚C ~ 30˚C) Abnormal ∞, 0Ω . . . Open or Short Samsung Electronics 12-22...
• Because the Test Mode operate the cool mode by force not related to the set temperature / indoor temperature, check whether each subordinate is operated normally or not after completing installation and must turn off the power of the air conditioner. Samsung Electronics...
Option error ◑ ◑ ◑ Option Setting (option wasn’t set up or option data error) Remote Control on/off ◑ ◑ Outdoor unit error Outdoor Unit Power Reset ● : Lamp on, : Lamp off, ◑ : Lamp blink Samsung Electronics...
● Power ON reset(1sec) ◎ ○ ○ Capacity miss match ○ ◎ ◎ Test Operation at Cooling Mode ◎ ◎ ◎ Test Operation at Heating Mode ● : LED ON, ○ : LED OFF, ◎ : LED BLINK Samsung Electronics...
Push the button to set the display panel to . Every time you push the button, the display panel reads . . . repeatedly. Samsung Electronics...
Page 55
If all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry. If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the correct option code is set up for its model. Samsung Electronics...
: BLADE CONTROL SELECT(UP/DOWN) MELODY CONTROL PART SLEEP OPERATION DC5V VOLTAGE REGULATOR ANION SELECT SPEAKER AUTO CLEAN SELECT OPTION ENERGY SAVING SELECT DC12V SMPS POWER BLOCK SOUND ON/OFF SELECT DIGITAL ON/OFF DC5V DC12V AC230V AC INPUT DC25V 13-1 Samsung Electronics...
Page 58
Block Diagram INDOOR FAN CONTROL BUZZER CONTROL SMPS AC COMMUNICATION SUB-PCB Samsung Electronics 13-2...
• 4 WAY CONTROL SIGNAL COMPRESSOR • PFC CONTROL SIGNAL • COMPRESSOR CONTROL(6P, BLDC) • LED CONTROL SIGNAL • INDOOR COMMUNICATION SIGNAL • 4 WAY VALVE SMPS • EEV INDOOR UNIT PFC CIRCUIT DC5V AC INPUT DC12V DC15V AC300V AC230V DC25V 13-3 Samsung Electronics...
Page 60
Block Diagram DIODE OUTDOOR FAN IGBT DC_LINK CAP SMPS Samsung Electronics 13-4...
10. PCB Diagram 10-1 Indoor PCB The red number connecter is not used. Power Temperature Sensor Motor RPM Feedback Auto Grill Remocon Module HVPS(High voltage Generator) Humidity Sensor BLADE-H Step Motor Anions Display Indoor Fan Motor Samsung Electronics 10-1...
10-2 Outdoor PCB The red number connecter is not used. Power N COND/OLP Temperature Sensor Power L DIS/OUT Temperature Sensor BLDC FAN EEV Connector AC FAN Comp. Connector Wire Communication 485 Reactor Connector Wire 10-2 Samsung Electronics...
9. Circuit Descriptions 9-1 PCB Circuit Descriptions 9-1-1 Indoor Unit SMPS BUZZER PART INDOOR FAN CONTROL SUB PCB CONNECTOR ZERO CROSSING PART DISPLAY STEP MOTOR & ION INDOOR TEMPERATURE SENSOR This Document can not be used without Samsung’s authorization. Samsung Electronics...
Page 88
Circuit Descriptions Circuit Descriptions 9-1-2 Outdoor Unit TEMPERATURE SENSOR & EEV BLDC FAN COMMUNICATION SMPS INVERTER This Document can not be used without Samsung’s authorization. Samsung Electronics...
9-2 Refrigerating Cycle Diagram Indoor Unit Outdoor Unit 2 way valve Expansion valve Liquid side Heat Exchanger (Evaporator) Heat Exchanger (Condenser) Cross Fan Gas side 4 way valve 3 way valve Cooling Compressor Heating Gas Leak Check Point Samsung Electronics...
11-1-1 Indoor Unit The design and shape are subject to change according to the model. Air Inlet Temperature sensor Air filter Air flow blades (under the grille) (outlet) Operation indicator (GREEN) Timer indicator (GREEN) Turbo indicator (RED) Power(On/Off) button Samsung Electronics 11-1...
Page 91
Operating Instructions 11-1-2 Outdoor Unit Air Inlet (Rear) Air Outlet Connection Valve 11-2 Samsung Electronics...
Maximum Silence mode Heat Mode Press the button on the remote control until is displayed. Press the button to select the fan speed until the required setting is displayed. Automatic (rotated : Medium High Maximum Silence mode 11-4 Samsung Electronics...
Page 94
You can select the Turbo function in the Auto, Cool and Heat mode. If you select this function in the Dry or Fan mode, it will return to the Auto mode. Good Morning Press the button one or more times until is displayed on your Mode remote control. Samsung Electronics 11-5...
③ : Use the " ③ " digit for classification between indoor and outdoor. Indoor "N" & Outdoor "X". ④ : Use the “ ④ ” digit for KD models. "CKD" "1" & "SKD" "2". Except the RAC Export Models for China. 14-1 Samsung Electronics...
It occurs when the drain pump is plugged out or it is out of order. Check the power of the drain pump and the position of the drain hose, and when the pump is faulty, contact the drain pump manufacturer. Samsung Electronics do not manufacture drain pumps.
Page 99
Also, the remote controller may not work under intensive light from a 3-wave length lamp or a neon sign due to the EMI. In this case, take the remote controller closer to the receiver. 14-5 Samsung Electronics...
Page 100
There is a cost table. But, our service engineer needs to visit to total up the cost correctly. When you move in, make sure to contact Samsung Electronics Service Center or Authorized Service Agent in advance to streamline the process.
Hook Body Note : • If you have not used the air conditioner for a long period of time, set the fan going for three to four hours to dry the inside of the air conditioner thoroughly. 14-7 Samsung Electronics...
Page 102
3. Wash the filters with clean water, then dry them in the shade. Bio Filter 4. Insert the filters into the original position. Note : • You can change the position of filters with each other. 5. Close the front grille. Samsung Electronics 14-8...
Electric and earth work shall meet the "Electric Facility Technology Standard" and the "Internal Wire Regulation" of the Electric Business Laws. Inspection & Trial Run Upon completion of the tests, you shall make a trial run while you explain the main functions of the air conditioner to finish the installation. 14-9 Samsung Electronics...
183kgf•cm with a torque wrench. 7) Check for gas leakage. - At this time, especially check for gas leakage from the 3 way valve’s stem nuts, and from the service port cap. Samsung Electronics...
Page 105
• Make sure you do not bend the connection pipes in the middle and store together with the cables. • Move the indoor and outdoor units to a new location. • Remove the mounting plate for the indoor unit and move it to a new location. 14-11 Samsung Electronics...
Do not place a cloth or other materials over it. Remove the batteries if you don’t use the remote control for a long time. (If applicable) Use the remote control within 7 meters from the indoor unit. (If applicable) Samsung Electronics...
Young children or infirm persons should be always supervised when they use the air conditioner. Max current is measured according to IEC standard for safety. Current is measured according to ISO standard for energy efficiency. Samsung Electronics...