Advertisement
1
Connect
Start with the 'Basic Connection.'
If you have a VCR, follow the instructions for 'Connection with a VCR or similar device'.
Basic Connection
Television (rear)
To antenna or
SCART IN
set-top box
To AC
power
Philips recorder
(rear)
EXT 2
AUX - I/O
EXT 1
TO TV - I/O
TV-OUT
ANTENNA-IN
~
MAINS
A
Before connecting, unplug the antenna cable that
is currently connected to your TV.
B
Connect the antenna cable to the ANTENNA-
IN
jack on the recorder.
C
Use the supplied RF coaxial cable to connect the
TV-OUT
jack on this recorder to the
Antenna In jack on the TV.
D
Use the SCART cable to connect the EXT1 TO
TV-I/O socket on this recorder to the
corresponding SCART input socket on the TV.
E
Connect the power cable from the recorder to
an AC power outlet.
dvdr3383_eu_qsg_eng_26261.indd 2
dvdr3383_eu_qsg_eng_26261.indd 2
Connection with a VCR or
similar device
A
Before Connecting
Your new Philips recorder replaces the VCR for your
recording needs. First, unplug all the connections
from your VCR.
B
Connecting
Television (rear)
To antenna or
SCART IN
set-top box
VCR or similar
device (rear)
To
AC power
EXT 2
AUX - I/O
EXT 1
TO TV - I/O
TV-OUT
ANTENNA-IN
~
MAINS
Philips
recorder
(rear)
A
Follow the steps under 'Basic Connections'
B
before you proceed to step
below.
B
Use another SCART cable (not supplied) to
connect the EXT2 AUX-I/O SCART socket
on this recorder to the SCART OUT socket on
the VCR.
C
Connect the power cable from your VCR to an
AC power outlet.
Note In this setup, the VCR cannot record TV
programmes.
For additional connection diagrams, see
the accompanying User Manual.
Set up
2
A
Finding the viewing channel
STANDBY-ON
Philips recorder (front panel)
A
Press STANDBY-ON on the recorder.
B
Switch on the TV set.
Note If connected to your VCR, make sure it
is switched off or in standby mode before
proceeding.
C
In case you do not see the recorder's blue
wallpaper, press "0" and the Channel Down
button on the TV's remote control repeatedly
(or AV, SELECT, ° button) until you see this
screen. This is the correct viewing channel for
the recorder.
B
Initial Installation
A
Press SYSTEM MENU
on the remote
control.
System Menu - General
Screen Saver
On
Country
Germany
Video Output Format
PAL
Restore Factory Settings
OK
Note Use up
or down
keys to toggle through
the options. Select an item by pressing right
. To
confi rm a setting, press OK
.
B
Select the country of your residence.
Highlight
and press right
.
Select { Country } and press right
to
access the options. Press OK
to confirm
your selection.
C
Select the OSD language.
.
Highlight
and press right
Select { On-Screen Display Language } and
press right
to access the options. Press
OK
to confirm your selection.
D
Setup and install TV channels.
Highlight
and press right
.
Select { Channel Search } and press OK
on the remote control to start automatic TV
channel search.
E
Setting the date and time.
Highlight
and press right
.
Select { Date (dd/mm/yy) } or { Time
(hh/mm/ss) } and press OK
.
Use the numeric keypad 0
-9
to
input the date/time, then press OK
to
confi rm.
Note The settings will be updated according to the
broadcast channel information of preset Programme
Number 1.
F
Press SYSTEM MENU
to exit.
2006-09-27 6:27:08 PM
2006-09-27 6:27:08 PM
Advertisement
