Table of Contents
Advertisement
Insert for liquid detergent
Position the insert for dispensing liquid detergent:
– Remove the detergent drawer completely
– Slide the insert forwards.
Do not use the insert (slide upwards):
– for gel detergents and washing powder,
– for programmes with
Prewash or the end time option.
Care
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Remove detergent and cleaning agent residue immediately.
– Do not clean with a jet of water.
Cleaning the detergent drawer ...
... if it contains detergent or fabric softener residues.
1. Pull out, press insert down, remove drawer completely.
2. To remove the insert: press the insert upwards from below with your finger.
3. Clean the detergent dispenser tray and insert with water and a brush and
dry it.
4. Attach the insert and engage (connect the cylinder to the guide pin).
5. Push in the detergent drawer.
Leave the detergent drawer open so that any residual water can
evaporate.
Drum
Leave the washing machine door open so that the drum can dry out.
Rust stains - use chlorine-free cleaning agent, not steel wool.
Descaling
This is not necessary if the detergent is dosed correctly. However, if it is necessary, follow the
instructions of the descaler manufacturer. Suitable descaling products can be purchased from
our website or after-sales service (
Information on the display panel
Door open?
Close the washing machine door properly; laundry may be caught.
Tap closed?
Open the tap completely, supply hose kinked or trapped; Clean the
filter
page 11, Water pressure too low.
Pump blocked?
Detergent solution pump blocked; Clean the detergent solution pump
page 11.
Drainage hose/waste pipe blocked; Clean the drainage hose at the
siphon
Top-up not possible;
Not possible to add more laundry. To continue, press the Start/Reload
water level too high
button.
or Temperature too high
F: 23
Water in the base tub, appliance leaking. Call the after-sales service.
F: 34
Washing machine door cannot be locked. Open the washing machine
door and close it with an audible "click"; switch the appliance off and
on again; set the programme and make your settings; start the
programme.
Other displays
Switch off the appliance, wait for 5 seconds and switch it back on. If
the display appears again, call the after-sales service
Downloaded From WashingMachine-Manual.com Manuals
model-dependent
page 10.
– Risk of electric shock. Disconnect the mains plug.
– Risk of explosion. No solvents.
No laundry in the machine.
page 13).
depending on model
page 11.
Information about blockages
Detergent solution pump
Turn the programme selector to Off and disconnect the mains plug.
1. Open and remove the service flap.
2. Take the drainage hose out of the retainer.
Remove the sealing cap, allow the detergent solution to flow out.
Push the sealing cap back on.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution
pump must rotate).
5. Replace the pump cover and screw it on tightly. The handle is vertical. Place the drainage hose
back into the retainer.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into
compartment II and start the
Drainage hose at the siphon
Turn the programme selector to Off and disconnect the mains plug.
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose clamp.
Filter in the water supply
Risk of electric shock
Do no immerse the Aqua-Stop safety device in water (it contains an electrical valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except
3. Choose
Start/Reload. Let the programme run for approximately 40 seconds.
4. Turn the programme selector to Off. Disconnect the mains plug.
5. Clean the filter:
Disconnect the hose from the tap.
Clean the filter with a small brush.
and/or for Standard and Aqua-Secure models:
Remove the hose from the rear of the appliance.
Remove the filter with pliers and clean.
6. Connect the hose and check for leaks.
page 13.
10
– Risk of scalding. Allow the detergent
solution to cool down.
– Turn off the tap.
Drain programme.
Spin/
Drain).
11
Advertisement
Table of Contents
