Table of Contents
Advertisement
www.freeservicemanuals.info
3.5.4 Separation - 1
Signal
Mode
Equipment
Measuring point (D)
EVR mode
EVR address
Specified value
Adjustment tool
(1) Set an audio signal mode of the RF signal generator to
alternate L-ch 300 Hz 14% modulated.
(2) Connect the equipment (C) to the measuring point (D).
(3) Set the VCR to the EVR mode by transmitting the code
(F1) from the Jig RCU.
(4) Set the EVR address to (F2) by transmitting the code (F3)
from the Jig RCU.
(5) Transmit the code (F4) from the Jig RCU to adjust so that
the level of the measuring point (D) becomes the speci-
fied value (G).
(6) Release the EVR mode of the VCR by transmitting the
code (F1) from the Jig RCU again. (When the EVR mode
is released, the adjusted data is memorized.)
3.5.5 Separation - 2
Signal
Mode
Equipment
Measuring point (D)
EVR mode
EVR address
Specified value
Adjustment tool
(1) Set an audio signal mode of the RF signal generator to
alternate L-ch 5 kHz 14% modulated.
(2) Connect the equipment (C) to the measuring point (D).
(3) Set the VCR to the EVR mode by transmitting the code
(F1) from the Jig RCU.
(4) Set the EVR address to (F2) by transmitting the code (F3)
from the Jig RCU.
(5) Transmit the code (F4) from the Jig RCU to adjust so that
the level of the measuring point(D) becomes the speci-
fied value (G).
(6) Release the EVR mode of the VCR by transmitting the
code (F1) from the Jig RCU again. (When the EVR mode
is released, the adjusted data is memorized.)
•
(A)
RF signal
(Audio: L-ch 300 Hz 14% modulated)
•
(B)
Tuner
•
EE
•
(C)
Audio level meter
•
IC6501 pin 26
•
(F1)
Jig code "57"
•
(F2)
A : 23
•
(F3)
Jig code "22" and "23"
•
(F4)
Jig code "18" or "19" (Channel +/-)
•
(G)
Minimum level
•
(H)
Jig RCU [PTU94023B]
•
(A)
RF signal
(Audio: L-ch 5 kHz 14% modulated)
•
(B)
Tuner
•
EE
•
(C)
Audio level meter
•
IC6501 pin 26
•
(F1)
Jig code "57"
•
(F2)
A : 24
•
(F3)
Jig code "22" and "24"
•
(F4)
Jig code "18" or "19" (Channel +/-)
•
(G)
Minimum level
•
(H)
Jig RCU [PTU94023B]
Published in Heiloo Holland
3.5.6 SAP VCO
•
Signal
(A)
No. signal
•
Mode
(B)
Tuner
•
EE
•
Equipment
(C)
Frequency counter
•
Measuring point (D1)
IC6501 pin 26
•
Short point
(D2)
C6505 (–) terminal
•
EVR mode
(F1)
Jig code "57"
•
EVR address
(F2)
A : 25
•
(F3)
Jig code "22" and "25"
•
(F4)
Jig code "18" or "19" (Channel +/-)
•
Specified value
(G)
78.67 ± 0.5 kHz
•
Adjustment tool
(H)
Jig RCU [PTU94023B]
(1) Connect the short wire between the short point (D2) and
the GND (Ground).
(2) Connect the equipment (C) to the measuring point (D1).
(3) Set the VCR to the EVR mode by transmitting the code
(F1) from the Jig RCU.
(4) Set the EVR address to (F2) by transmitting the code (F3)
from the Jig RCU.
(5) Transmit the code (F4) from the Jig RCU to adjust so that
the frequency of the measuring point (D1) becomes the
specified value (G).
(6) Release the EVR mode of the VCR by transmitting the
code (F1) from the Jig RCU again. (When the EVR mode
is released, the adjusted data is memorized.)
(7) Disconnect the short wire between the short point (D2)
and the GND (Ground).
3.6 Digital circuit
3.6.1 D-VHS REC level
•
Signal
(A1)
Ext. input
•
(A2)
Optional
•
(A3)
DF-300
•
Mode
(B1)
D-VHS STD REC
•
(B2)
D-VHS HS REC
•
Equipment
(C)
Oscilloscope
Measuring point (D)
(STD)
(HS)
External trigger
(E)
(STD)
(HS)
•
EVR mode
(F1)
Jig code "57"
EVR address
(F2)
(STD)
(HS)
(F3)
(STD)
(HS)
•
(F4)
Jig code "18" or "19" (Channel +/-)
•
Specified value
(G)
100 (105-110) mVp-p
•
Adjustment tool
(H)
Jig RCU [PTU94023B]
(1) Insert the cassette tape (A3) to enter the mode (B1).
(2) Apply the external trigger signal to D.FF (E) to observe
the waveform appeared at the measuring point (D).
(3) Set the VCR to the EVR mode by transmitting the code
(F1) from the Jig RCU.
(4) Set the EVR address to (F2) by transmitting the code (F3)
from the Jig RCU.
(5) Transmit the code (F4) from the Jig RCU to adjust so that
the waveform signal level "a" becomes the specified value
(G).
29/11/2016
•
TP601 (REC LEVEL1)
•
TP602 (REC LEVEL2)
•
TP111 (VIDEO/STD/HS1 FF)
•
TP112 (A/HS2 FF)
•
A:08
•
A:09
•
Jig code "20" and "28"
•
Jig code "20" and "29"
3-6
Hide quick links:
Advertisement
Table of Contents
