Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Curtis ILGD
Summary of Contents for Curtis ILGD
- Page 1 Service Manual – Digital Interlock Grinders ind out more on the web wilburcurtis Models Included u IlGd u Tl-IlGd IlGd dIGITal InTerlock coffee GrInders Wilbur Curtis Company • montEbEllo, Ca usa FOR THE LATEST SPEC INFORMATION GO TO WWW.WILBURCURTIS.COM Iso 9001 reGIsTered...
-
Page 2: Table Of Contents
Parts list ................10 Warranty ................11 IMPORTANT IMPORTANT SAFEGUARDS/CONVENTIONS This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should SAFEGUARDS/ be performed by an authorized Wilbur Curtis service center. CONVENTIONS • Do NOT immerse the unit in water or any other liquid • No user serviceable parts are located inside. Repair should be done only by authorized service personnel. • Keep hands and other items out of the hopper during operation. -
Page 3: Contents & Unpacking
SHIPPING CARTON CONTENTS & UNPACKING UNPACKING UNPACKING All products manufactured by the Wilbur Curtis Company are thoroughly inspected at the factory, and are warrantied to be free of all defects and faulty workmanship. Each grinder is packaged for maximum protec- tion during shipping. Make sure the shipping carton is not damaged or punctured. Unpack the carton care- fully, inspecting the contents for any damage that may have occurred in transit. -
Page 4: Troubleshooting Guide
TROUblE- ShOOTING This appliance is designed for commercial use. any servicing other than cleaning and maintenance should be performed by an authorized Wilbur curtis service center. GUIDE SyMPTOM: MOTOR DOES NOT RUN POSSIblE CAUSE SOlUTION 1. Circuit breaker may be tripped. -
Page 5: Adjusting Grinds
ADjUSTING 1. Empty hopper of coffee beans. Run grinder to clear grinding burrs of coffee. 2. Open housing cover to locate adjustment screw (8) and lock nut (7). loosen lock nut. ThE GRINDS* 3. Run motor during adjustment. Turning adjustment screw clockwise will result in a finer grind (if, while turning, you hear the grinding burrs starting to touch, immediately, back off 1/8th turn). Turning counter clockwise will produce a coarser grind. 4. with a screwdriver holding the adjustment screw in place, tighten the locknut. 5. Run some coffee beans through the machine to check the grind adjustment. -
Page 6: Programming
Weigh your out- 10.0 put, then make adjustments as 11.8 necessary. 13.5 ROUGh-IN DRAWINGS 13.50" (34.2 cm) 2.00" (5.1 cm) IlGD / Tl-IlGD 29.38" (74.5 cm) TOP ViEW 10.00" 14.50" " (25.4 cm) (37.0 cm) (7.0 cm) -
Page 7: Electrical Schematics
ElECTRICAl SChEMATICS IlGD / Tl-IlGD... -
Page 8: Parts Diagrams
PARTS DIAGRAMS HOPPER & TOP COVER 9 10 CENTER COVER & GEARMOTOR... -
Page 9: Parts Diagrams
PARTS DIAGRAMS MOTOR & bASE... -
Page 10: Parts List
MOTOR, GEAR 115V DUAl GRINDER WC-1504 BREAKER, CIRCUIT 10A 120/250VAC wC- 689* CONTROl bOARD, IlGD, DhGIlD wC-9164 COVER ASSEMBly, SPOUT (OPTIONAl FOR DHG-20) wC-9126 GUIDE, SPOUT W/A ShG DhG IlGD wC-39212 MEMbRANE CONTROl PANEl, IlGD wC-39248 MEMbRANE CONTROl PANEl, Tl-IlGD wC-3796 lAbEl, ADjUSTMENT INFO ShG, DhG wC-9107-6* DISK, SHEAR COFFEE GRINDER 6PK... -
Page 11: Warranty
Wilbur curtis company, Inc. The Wilbur curtis company will not accept any responsibility if the fol- lowing conditions are not met. The warranty does not cover and is void under the following circumstances: 1) Improper operation of equipment: The equipment must be used for its designed and intended purpose and function. - Page 12 WIlBur curTIs coMPany, Inc. 6913 Acco Street • Montebello, CA 90640-5403 USA Phone: 800-995-0417 (M-F 5:30A - 4:00P PST) • Fax: 323-837-2410 Technical support email: Techsupport@wilburcurtis.com www.wilburcurtis.com 3/09 . F-3117 rev.C 3/30/8 . 10.8 . ecn 9382 9/1/00 15.6 . F - 3117 RevA.p65 ECN 3719 7/5/01.13.0.F-3117revB.qxd.ECN-4383...