Sanyo VHR-VK310A Service Manual
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. VCR
  5. VHR-VK310A
  6. Service manual
Sanyo VHR-VK310A Service Manual

Sanyo VHR-VK310A Service Manual

Video cassette recorder
Hide thumbs Also See for VHR-VK310A:
Table of Contents

Advertisement

Quick Links

See also: User Manual
SERVICE MANUAL
Video Cassette Recorder
STOP
EJECT
-
CHANNEL
+
VIDEO IN
L-AUDIO IN-R
AV2
(VHR-VK910A)
CAUTION
This product utilizes a laser.
The adjustment other than those specified herein
may result in hazardous radiation exposure.
REW
FF
P/STILL
REC/ITR
PLAY
FILE NO.
VHR-VK310A
(Product Code : 168 233 577)
(AUSTRALIA)
VHR-VK310A/NZ
(Product Code : 168 233 579)
(NEWZEALAND)
VHR-VK910A
(Product Code : 168 233 578)
(AUSTRALIA)
VHR-VK910A/NZ
(Product Code : 168 233 580)
(NEWZEALAND)
REFERENCE No.SM310001

Advertisement

Table of Contents
loading

Related Manuals for Sanyo VHR-VK310A

Summary of Contents for Sanyo VHR-VK310A

  • Page 1 FILE NO. SERVICE MANUAL Video Cassette Recorder VHR-VK310A (Product Code : 168 233 577) (AUSTRALIA) VHR-VK310A/NZ (Product Code : 168 233 579) (NEWZEALAND) VHR-VK910A (Product Code : 168 233 578) (AUSTRALIA) VHR-VK910A/NZ (Product Code : 168 233 580) (NEWZEALAND) STOP...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS SECTION 1 CIRCUIT DIAGRAMS ....3-30 1. Power Circuit Diagram ....3-30 SUMMARY 2.

  • Page 3: Key To Abbreviations

    SECTION1 SUMMARY KEY TO ABBREVIATIONS :Alternating Current :Low Pass Filter :Automatic Color Control :Maximum ACSS :Automatic Channel Setting System :Modulator :Adjust MECHA.CTL :Mechanism Control :Audio Erase :Microphone :Automatic Frequency Control :Minimum :Automatic Fine Tuning :Mixer, Mixing :Automatic Gain Control M.M. :Monostable, Multivibrator A.H.SW :Audio Head Switch...

  • Page 4: Product Safety Servicing Guidelines For Video Products

    When servicing this product, under no circumstances should the original design be modified or altered without permission from SANYO Electronics Corporation. All components should be replaced only with types identical to those in the original circuit and their physical location, wiring and lead dress must conform to original layout upon completion of repairs.

  • Page 5: Servicing Precautions

    SERVICING PRECAUTIONS CAUTION : Before servicing the VCR covered by this service Electrostatically Sensitive (ES) Devices data and its supplements and addends, read and follow the Some semiconductor (solid state) devices can be damaged SAFETY PRECAUTIONS. NOTE : if unforeseen circum- easily by static electricity.

  • Page 6: Protection

    PROPOSAL FOR APPLYING SHORT PROTECTION • The Contents of Examination As all the IC that is applied to VCR is controlled by IIC, mutual communication, if Vcc of IC is short or open with detecting ‘Acknowledge’ data of the specific IC according to each power(5V, 5VT) µ-COM gets unable to detect ‘ACK’...

  • Page 7: Service Notice On Replacing Eeprom

    SERVICE NOTICE ON REPLACING EEPROM In case that defective EEPROM of PAL models is replaced, to operate these sets from the initial state MP KEY must be repaired as well before delivering to the customer. If MP KEY isn’t repaired the setting of RF OUT channel or LANGUAGE might be different from that for cus- tormer’s country.

  • Page 8: Ic Setting

    Insert the PAL SP Test Tape and play. Note - Adjust the distance of X, pressing the MODEL NAME BINARY Tracking(+) or Tracking(-) when the “ATR” is VHR-VK310A OPTION1 00000000 blink after the PAL SP Test Tape is inserted. (AUSTRALIA) OPTION2 00000000 b) Press the Auto PG KEY on JIG Remocon(1’st) or Press...

  • Page 9: Specifications

    SPECIFICATIONS General Power : 110~240V, 50/60Hz Power consumption : Approx. 12 watts(Energy Saving mode : 3 watts) Video Head system : Rotary 2heads, helical scanning system (2HD MODEL) Double azimuth 4 heads, helical scanning system (4HD MONO, 4HD Hi-Fi Model Only) Tape speed : 23.39 mm/sec (SP mode)11.69 mm/sec(LP mode) Tape format...

  • Page 10: Service Method

    SECTION2 CABINET & MAIN FRAME SERVICE METHOD (1) Disassembly Flow (2) Re-assembly Flow for service like Fig. 2-1 Top Case LED C.B.A Bottom Cover Main C.B.A Front Panel Housing & Deck Assembly Housing & Deck (3) To check and replace Electrical parts Assembly Disassemble the unit according to No.1) Disassembly Flow.

  • Page 11: Exploded Views

    EXPLODED VIEWS 1. Cabinet and Main Frame Section NOTE) Refer to “SECTION 5 REPLACEMENT PARTS LIST” in order to look for the part number of each part. _ OPTIONAL PARTS...

  • Page 12: Packing Accessory Section

    2.Packing Accessory Section INSTRUCTION ASS'Y 810 CABLE SET ASS'Y BATTERY 803 PACKING 900 REMOCON 804 BAG 802 BOX...

  • Page 13: Electrical Adjustment Points Arrangement

    SECTION 3 ELECTRICAL ELECTRICAL ADJUSTMENT POINTS ARRANGEMENT : Measurement point : Adjustment point 3/4 CH SWITCH A/V JACK SMPS AVCP Hi-Fi DECK CNT. TUNER & MODULATOR SYSTEM U-COM DRIVE CLK/DOT DISP BOARD(L) BOARD(R)

  • Page 14: Electrical Adjustment Procedures

    ELECTRICAL ADJUSTMENT PROCEDURES 1. Servo Adjustment 1) PG Adjustment • Test Equipment a) OSCILLOSCOPE b) PAL TEST TAPE (VHS SP) c) JIG REMOCON (AUTO PG SETTING) • Adjustment And Specification MODE MEASUREMENT POINT ADJUSTMENT POINT SPECIFICATION V.Out PLAY 6.5 ± 0.5H H/SW(W714, W715) •...
  • Page 15 ELECTRICAL ADJUSTMENT PROCEDURES • WAVEFORM H/SW 6.5H(416us) Composite VIDEO • Attension and Reference a) The PG checking must do when RF Level is Maximum and SERVO system is Locking (MTR MODE) b) V.H/SW Level is 2Vpp.

  • Page 16: Electrical Troubleshooting Guide

    ELECTRICAL TROUBLESHOOTING GUIDE 1. Power Circuit(SMPS) (1) No 5.3VA. No 5.3VA. Replace the F101 Is the F101 normal? (Use the same Fuse). Is the BD101 normal? Replace the BD101. Is the R101 normal? Replace the R101. Does the oscillation waveform appear at Is Vcc(about 13~15V) permittable at the the IC101 Pin 7? IC101 Pin 3?
  • Page 17 7. Power Circuit(SMPS) (2) No 12VA.(Capstan) No 12VA. Does 5.3VA work normally? Check whether 5.3VA is out of order. Is the D109 normal? Replace the D109. Check 12VA Line of the Main PCB short. (3) No 12V (Hi-Fi, Buffer) No 12VA. Is Vcc(about 12V) put into the Q152(E)? Replace the Peripheral Circuitry of ZD152.
  • Page 18 7. Power Circuit(SMPS) (4) No 5V No 5V. Is 5.3VA put into the Q155(Q157) collector? Is the Q156 Base “H”? Check the µ-com Control. Is about 4.7V put into the Check the Q156 Q155(Q157) Base? whether it works normally. Check or Replace the Q155(Q157).

  • Page 19: Servo Circuit

    2. Servo Circuit Unstable Video in PB Mode. Does the on screen noise level change periodically? Do CTL pulses appear at IC501 pin 97? Does the CFG divide Is the height of the CTL waveform appear at IC501 Head adjusted correctly? pin 87? Do the CTL pulses move Adjust the CTL Head.
  • Page 20 Drum Motor stopped. Does 12V appear at PMC01 PIN8? Does Drum CTL signal appear at PMC01 Check Power. PIN12? Does Drum PWM appear at IC501 Check Connector and Drum Motor Ass’y. Pin 76? Check the Components and foil Pattern Do DPG/FG Pulses appear at PMC01 between IC501 Pin 76 and PMC01 Pin 11? Pin 12 for shorts.
  • Page 21 Capstan Motor Stopped. Does 12VA appear at PMC01 Pin 2? Does 2.8V appear at PMC01 Pin 9? Check Power. Check Connector and Capstan Does PWM wave appear at IC501 Motor Ass’y. Pin 77? Check the Components and foil Patterns Does the CFG signal appear at PMC01 Connected between IC501 Pin 77 and Pin 1? PMC01 Pin 9 for shorts.

  • Page 22: System & Front Panel Circuit

    3. System & Front Panel Circuit Auto stop. Does SW30 waveform appear at IC501 Pin 18? Do Take-up reel pulses Check the Drum Motor appear at IC501 Pin 80? Signal. Does 5.3V appear at Change IC501. RS501. Replace the Take-Up Reel Photocoupler on Main Check the Power.
  • Page 23 Cassette tape loading is unstable. Is REG 12V applied to PMC01 Pin 8? Is High signal applied to IC501 Pin 58 Check the power. When inserting the CST? Is 5.3V applied to R544? Does Low signal occur form IC501 Pin 60 Check the CST SW and Check the power.
  • Page 24 Non working functon buttons. Is the voltage of IC501 Pin 99, 5V? Does LED CLOCK, LED DOT display change when a function button is Check the power. pressed? Replace the defective Switch. Replace IC501. (Function SW) LED CLOCK, LED DOT doesn’t work. Is 5V applied to IC501 Pins 37 and Check the power circuit.

  • Page 25: Y/C Circuit

    4. Y/C CIRCUIT (1) No Video in EE Mode, No Video in EE Mode Check the Video Input Does the Video signal Jack. appear at the IC301 Pin 48? (Line In Jack) Is 5V applied to the IC301 Check the 5.2V, 5.4VA Pins 18, 24, 42, 55, 72, 91? Line.
  • Page 26 3. Y/C CIRCUIT (2) When the Y(Luminance) signal doesn’t appear on the screen in PB Mode, Is 5.2VT, 5.4VA applied to the Check the line of the 5.2V Line. (Power Circuit) IC301 Pins 24, 42, 55, 72, 91? Is the I C Bus siganl applied Refer to ‘SYSTEM I C BUS...
  • Page 27 3. Y/C CIRCUIT (3) When the C(Color) signal doesn’t appear on the screen in PB Mode, Is 5.2V/5.3VA applied to the Check the line of the 5.2V/ 5.3VA Line. (Power Circuit) IC301 Pins 24, 42, 55, 72, 91. Is the Color Rotary signal Check the Color Rotary applied to the IC301 Circuit.
  • Page 28 3. Y/C CIRCUIT (4) When the Video signal doesn’t appear on the screen in REC Mode, Is the EE signal normal? Check EE Mode. Is 5.2V/5.3VA applied to the Check the line of the 5.2V/ IC301 Pins 24,42,55,72,91? 5.3VA Line.(Power Circuit) Does PB Mdoe operate Check PB Mode.

  • Page 29: Tuner/If Circuit

    5. Tuner/IF circuit (1) No picture on the TV screen No picture on the TV screen Does the Video signal at Is +30V applied to Check 34V line. the TU701 Pin24? TU701 Pin 16? Is +5.2V applied to Check 5.2V line. TU701 Pin 13? Does the Clock signal Check the liC Clock...
  • Page 30 (2) No sound (Mono Model) No sound Check the Vcc of IC301 Pin 18. Check 5.2V power. Check the Tuner Audio signal Chekc the signal flow from TU701 at IC301 Pin 13. Pin21 to IC301 Pin 13. Check the Audio signal at IC301 Pin 11. Replace IC301.
  • Page 31 (3) No sound (Hi-Fi Model) No sound Check the Vcc of IC751 Pins 1, 19, 33. Check 5V power. Check the Tuner SiF signal at IC751 Pin 2. Check the Tuner Audio of TU701 Pin 21. Check the oscillator of IC751 Pins 5, 6. Replace X751.

  • Page 32: Hi-Fi Circuit

    6. Hi-Fi Circuit (Hi-Fi Model) Hi-Fi Playback. Check the Vcc of No sound IC801.(Pins 34, 40) Check the Hi-Fi Selection Check power. Switch and the Tape quality. Is the RF Envelope at Is the Head switching signal Check IC501 Pin 19. IC801 Pin 44 over 2Vp-p? IC802 Pin 41 O.K? (Audio head switch 25)
  • Page 33 Hi-Fi REC. It is impossible to record and playback Hi-Fi Audio signal. Check Vcc of IC801. (Pins 34,40) Check IC801 Pin 42(Data),Pin 43(CLOCK). Check Power. Do Audio signals appear at IC801 Check ports of µ-COM. Pins 16, 17? Do FM Audio signals appear at IC801 Check Audio input signal of IC801 Pin 36? Pins 2, 3(TU.A.), 6, 7(Scart 1)
  • Page 34 SECTION 4 MECHANISM CONTENTS DECK MECHANISM PARTS DECK MECHANISM ADJUSTMENT LOCATIONS • Tools and Fixtures for Service ....4-12 1. Mechanism Alignment Position Check..4-13 • Top View............4-1 2. Preparation for Adjustment......4-14 • Bottom View ..........4-1 3. Checking Torque ........4-14 4. Guide Roller Height Adjustment....4-15 DECK MECHANISM 4-1.

  • Page 35: Deck Mechanism Parts Locations

    DECK MECHANISM PARTS LOCATIONS • Top View Procedure Fig- Part Fixing Type Starting 1 Drum Assembly 3 Screw 2 Plate Top 2 Hook 3 Holder Assembly CST Chassis Hole 4 Opener Door Chassis Hole 5 Bracket Assembly 3 Hook L/D Motor 2,3,4 6 Gear Assembly Rack F/L 1 Hook, Chassis Hole A-2...

  • Page 36: Deck Mechanism Disassembly

    DECK MECHANISM DISASSEMBLY Stator (S2) (S2) (S3) Drum Motor (S3) Rotor Drum Sub Assembly (Fig. A-1-1) Drum FPC Carbon Brush (S1) (S1) (S1) Holder FPC Fig. A-1 (Fig. B-1) 1. Drum Assembly (Fig. A-1-1) 1) Unplug the Drum FPC Connector. 2) Remove three Screws(S1) on bottom side and separate the Drum assembly.
  • Page 37 DECK MECHANISM DISASSEMBLY (Fig. A-2-1) Plate Top (B') (Fig. A-2-2) Holder Assembly CST (Fig. A-2-6) Arm Assembly F/L (C1) (Fig. A-2-7) Lever Assembly S/W (H8) Bracket Assembly L/D Motor Spring Lever S/W (Fig. A-2-4) (C') (E') Opener Door (Fig. A-2-3) (H6) Chassis Gear Assembly Rack F/L...

  • Page 38: Plate Top

    DECK MECHANISM DISASSEMBLY 2. Plate Top (Fig. A-2-1) 2) Unhook three Hooks(H3, H4, H5) on bottom side of the Chassis, lift up the Bracket Assembly L/M and disassem- 1) Pull the (B) portion of the Plate Top back in direction of ble the Bracket Assembly L/D Motor.

  • Page 39: Arm Assembly Cleaner

    DECK MECHANISM DISASSEMBLY Arm Assembly Cleaner (Fig. A-3-1) (S4) Base Assembly A/C Head (Fig. A-3-3) Head F/E (Fig. A-3-2) Chassis Fig. A-3 9. Arm Assembly Cleaner (Fig. A-3-1) 11. Base Assembly A/C Head (Fig. A-3-3) 1) Breakaway the (A) portion as Fig. A-3-1 from the 1) Remove the Screw(S4) and lift the Base Assembly A/C embossing of the Chassis, turn the Arm assembly Head up.

  • Page 40: Brake Assembly T

    DECK MECHANISM DISASSEMBLY Arm Assembly Tension (Fig. A-4-3) (H11) Spring TB Brake Assembly T (Fig. A-4-1) Spring Tension Reel S Reel T (Fig. A-4-4) (Fig. A-4-4) Spring RS Brake Assembly RS (Fig. A-4-2) (H12) (H9) (H10) Base Tension Chassis Fig. A-4 12.

  • Page 41: Base Assembly P4

    DECK MECHANISM DISASSEMBLY Opener Lid (Fig. A-5-2) Assembly Pinch (Fig. A-5-3) Base Assembly P4 Lever T/up (H13) (Fig. A-5-1) (Fig. A-5-4) (H13) Arm T/up (Fig. A-5-5) Chassis Fig. A-5 16. Base Assembly P4 (Fig. A-5-1) NOTE 1) Breakaway the (A) portion of the Base Assembly P4 from When reassembling, confirm the (C) portion of the Arm the embossing of the Chassis.

  • Page 42: Belt Capstan/Motor Capstan

    DECK MECHANISM DISASSEMBLY Belt Capstan (Fig. A-6-1) Motor Capstan (Fig. A-6-2) Washer(W1) Clutch Assembly D35 (Fig. A-6-4) (L1) (L1) Brake Assembly Capstan (Fig. A-6-5) Lever F/R (Fig. A-6-3) (L2) Chassis (S5) Fig. A-6 20. Belt Capstan (Fig. A-6-1)/ 22. Clutch Assembly D35 (Fig. A-6-4) Motor Capstan (Fig.

  • Page 43: Gear Drive/Gear Cam

    DECK MECHANISM DISASSEMBLY (H14) Gear Cam Hole(B) Gear Cam (Fig. A-7-2) Gear Drive Hole(A) Washer (W2) Gear Sector (Fig. A-7-3) Plate Slider Gear Drive (Fig. A-7-4) (Fig. A-7-1) Lever Tension (Fig. A-7-5) Lever spring (L3) (Fig. A-7-6) Gear Drive Hole(C) Base Loading (H15) (H16)

  • Page 44: Gear Assembly P2

    DECK MECHANISM DISASSEMBLY Gear Assembly P2 Hole Gear Assembly P3 Hole Gear Assembly P3 (Fig. A-8-2) Gear Sector Hole(A) Lever Spring Boss Gear Assembly P2 Plate Slider Hole(B) (Fig. A-8-1) Chassis Base Assembly P3 (Fig. A-8-4) Base Assembly P2 (Fig. A-8-3) Fig.

  • Page 45: Base Loading

    DECK MECHANISM DISASSEMBLY (S7) Base Tension Base Loading (Fig. A-9-2) Arm Assembly Idler (Fig. A-9-1) (Fig. A-9-3) Chassis Fig. A-9 31. Base Loading (Fig. A-9-1) 33. Arm Assembly Idler (Fig. A-9-3) 1) Remove the Screw(S7). 1) Make narrower the two parts, (A) and (B), as Fig. A-9-3. 2) Lift the Base Loading up.

  • Page 46: Deck Mechanism Adjustment

    DECK MECHANISM ADJUSTMENT • Tools and Fixfures for Service 1. Cassette Torque Meter 2. Alignment Tape 3. Torque Gauge SRK-VHT-303(Not SVC part) Parts No NTSC: DTN-001 600g.Cm ATG Parts No: D00-D006 PAL:DTN-0002 Parts No:D00-D002 4. Torque Gauge Adaptor 5. Post Height Adjusting Driver 6.

  • Page 47: Mechanism Alignment Position Check

    DECK MECHANISM ADJUSTMENT 1. Mechanism Alignment Position Check Purpose:To determine if the Mechanism is in the correct position, when a Tape is ejected. Test Conditions (Mechanism Test Equipment/ Fixture Check Point Condition) • Mechanism and Mode Switch Position • Blank tape •...

  • Page 48: Preparation For Adjustment

    DECK MECHANISM ADJUSTMENT 2. Preparation for Adjustment (To set the cassette without tape. Cover the holes of the End Sensors at the both sides of Deck Mechanism of the loading state the Chassis to prevent a light leak. without inserting a cassette tape). Then the Deck Mechanism drives to the Stop Mode.

  • Page 49: Guide Roller Height Adjustment

    DECK MECHANISM ADJUSTMENT 4.Guide Roller Height Adjustment Purpose: To regulate the height of the tape so that the bottom of the tape runs along the tape guide line on the Lower Drum. 4-1. Preliminary Adjustment Test Equipment/ Fixture Test Conditions (Mechanism Condition) Adjustment Point •...

  • Page 50: Audio/Control (A/C) Head Adjustment

    DECK MECHANISM ADJUSTMENT 5. Audio/Control (A/C) Head Adjustment Purpose: To insure that the tape passes accurately over the Audio and Control Tracks in exact alignment of the both Record and Playback Modes. 5-1. Preliminary Adjustment (Height and Tilt Adjustment) Perform the Preliminary Adjustment, when there is no Audio Output Signal with the Alignment Tape. Test Equipment/ Fixture Test Conditions (Mechanism Condition) Adjustment Point...

  • Page 51: Precise Adjustment(Azimuth Adjustment)

    DECK MECHANISM ADJUSTMENT 5-2. Confirm that the tape passes smoothly (2) If folding or curling is observed at the top of it then slowly turn the Tilt Adjustment Screw(C) in the between the Take-up Guide and Pinch counterclockwise direction. Roller(using a mirror or the naked eye). 1) After completing Step 5-1.(Preliminary Adjustment), check NOTE: that the tape passes around the Take-up Guide and Pinch...

  • Page 52: Waveform

    DECK MECHANISM ADJUSTMENT 7. Adjustment after Replacing Drum Assembly (Video Heads) Purpose: To correct for shift in the Roller Guide and X value after replacing the Drum. Test Conditions Test Equipment/ Fixture Connection Point Adjustment Points (Mechanism Condition) • CH-1: PB RF Envelope •...

  • Page 53: Maintenance/Inspection Procedure

    MAINTENANCE/INSPECTION PROCEDURE 1. Check before starting repairs The following faults can be remedied by cleaning and oil- ing. Check the needed lubrication and the conditions of cleanliness in the unit. Check with the customer to find out how often the unit is used, and then determine that the unit is ready for inspec- tion and maintenance.

  • Page 54: Required Maintenance

    MAINTENANCE/INSPECTION PROCEDURE 2. Required Maintenance 4. Supplies Required for Inspection and Maintence The recording density of a VCR(VCP) is much higher than that of an audio tape recorder. VCR(VCP) components must (1) Grease : Kanto G-311G (Blue) or equivalent be very precise, at tolerances of 1/1000mm, to ensure com- (2) Isopropyl Alcohol or equivalent patibility with the other VCRs.

  • Page 55: Greasing

    MAINTENANCE/INSPECTION PROCEDURE 5-2) Greasing (2) Periodic greasing Grease specified locations every 5,000 hours. (1) Greasing guidelines 1) Loading Path Inside & Top side 6) Plate Slider Guide Sections Apply grease, with a cleaning patch. Do not use excess 2) Base Assembly P2,P3 stopper 7) Plate Slider Guide Sections grease.
  • Page 56 MAINTENANCE/INSPECTION PROCEDURE Lever, F/R, Base, Tension GEAR AY, P2 & P3 Boss Lever, F/R Base, Tension Clutch (G-754. Yellow) Arm Tension Guide Hole 4-22...

  • Page 57: Mechanism Troubleshooting Guide

    MECHANISM TROUBLESHOOTING GUIDE 1.Deck Mechanism Auto REW doesn't work. Is the output of END sensor of supply side "H"? “H”: more than 3.5V “L”: less than 0.7V~1V Is the Vcc. voltage of End Check the syscon power. sensor 5V? Replace the End sensor. Is the voltage across IR LED Replace the IR LED.
  • Page 58 MECHANISM TROUBLESHOOTING GUIDE AUTO STOP. (PLAY/CUE/REV) Check alignment positions (page 4-14). In Play/Cue/Rev, Is the Pinch Roller in contact with the Is the output of DFG, DPG OK? Replace the Drum Motor. Capstan Shaft? Are there T/up and Supply Reel Check the Servo, Syscon.
  • Page 59 MECHANISM TROUBLESHOOTING GUIDE In PB mode Tape Presence not sensed. Is the Pinch Roller attached Check Alignment positions to the Capstan Motor Shaft? (page 4-14). Does the T/Up Reel turn? Is the Belt ok? Replace the Belt. Check the Clutch and Idler Does the Capstan Motor turn? Assembly.

  • Page 60: Main P.c.board

    MECHANISM TROUBLESHOOTING GUIDE 2. Front Loading Mechanism Cassette cannot be inserted. Does the Lever Assembly Is the Lever Assembly Switch Replace or add the Lever Switch work? Spring damaged or omitted? Assembly Switch Spring. Does the CST IN Switch work Replace the CST IN Switch.
  • Page 61 MECHANISM TROUBLESHOOTING GUIDE Cassette does not load. Does the cassette insert? Does the Opener Lid work? Does the Gear Assembly Rack F/L Replace the Opener Lid. work? Replace the Gear Rack F/L. Does the Opener Door work? Check the opener Door assembled Does the Arm Assembly F/L work? correctly.

  • Page 62: Exploded Views

    EXPLODED VIEWS 1. Front Loading Mechanism Section 4-28...

  • Page 63: Moving Mechanism Section (1)

    EXPLODED VIEWS 2. Moving Mechanism Section(1) OPTIONAL PART 4-29...

  • Page 64: Moving Mechanism Section (2)

    EXPLODED VIEWS 3. Moving Mechanism Section(2) OPTIONAL PART 4-30...
  • Page 65 MEMO...

  • Page 66: Replacement Parts List

    Parts that are shaded are critical NOTES) With respect to risk of fire or NOTES) electricial shock. SECTION 5 REPLACEMENT PARTS LIST SANYO MODEL : VHR-VK310A(SANYO) AUSTRALIA NSP : Not available as service parts. RUN DATE :19-SEPTEMBER-03 AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION...
  • Page 67 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C115 LG624-085D CAPACITOR CE 47UF/50V KME (SMPS) C116 LG0CE108BF630 CAPACITOR,FIXED ELECTROLYTIC 1000UF KME 16V M FM5 BULK C117 LG0CE3376D638 CAPACITOR,ELECTROLYTIC 330UF SMS 10V M FM5 TP5 C120 LG0CE477BH630 CAPACITOR,AL.ELECTROLYTIC 470UF KME TYPE 25V M FM5 BULK...
  • Page 68 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C341 LG0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S C342 LG0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA C343 LG0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V)
  • Page 69 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C561 LG0CE1064F638 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) C566 LG0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V TA26 C567 LG0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V TA26 C568 LG0CN1020K518 CAPACITOR TUBULA(HIGH DIELE)
  • Page 70 ALTERNATE IC102 LG6500RDB010A SENSOR PC123YN2 SHARP PHOTOCOUPLER IC103 LG0IKE431000A IC,KEC KIA431 3 PIN TP IC301 LG0ILNRSA006B IC,LINEAR LA71730EM SANYO 100PIN QFP TRA IC501 LG0IMCRMI026E IC,MICRO CONTROLLER M37762MCA-1M0GP MITSUBISHI 100 IC503 LG0IAL241600B IC,ATMEL AT24C16 - - - - IC503 LG0ICS241600B IC,CATALYST...
  • Page 71 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS L314 LG0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP L501 LG0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP L510 LG0LR0682K035 INDUCTOR RADIAL LEAD 68M K 6X6 L5 TP...
  • Page 72 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS Q504 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ALTERNATE Q506 LG0TR120109AC TRANSISTOR SRC1201 TP AUK TO92 4.7K,4.7K Q507 LG0TR198009CA TRANSISTOR 2SA1980G TP AUK TO92 Q5S1 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92...
  • Page 73 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R318 LG0RD3901F608 RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5% TA26 R319 LG0RD5600F608 RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5% TA26 R320 LG0RD1500F608 RESISTOR,FIXED CARBON FILM 150 OHM 1/6 W 5% TA26...
  • Page 74 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R532 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26 R533 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26 R534 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26...
  • Page 75 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R705 LG0RD1201F608 RESISTOR,FIXED CARBON FILM 1.2K OHM 1/6 W 5% TA26 R707 LG0RD5600F608 RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5% TA26 R790 LG0RD1501F608 RESISTOR,FIXED CARBON FILM 1.5K OHM 1/6 W 5% TA26...
  • Page 76 RACK F/L LG4261R-0023A ARM ASSY LG4510R-0046A LEVER ASSY SWITCH LG6723R-0304B DRUM(CIRC) ASSEMBLY SUB D35-2CH (8M2) LG4680R-B008A MOTOR(MECH) DRUM VH4302-800 SANYO FOR D35K LG4680R-B010A MOTOR(MECH) DRUM MDVC-035KA LGIT FOR D35K ALTERNATE LG4680R-B009A MOTOR(MECH) DRUM I2OAL21 SANKYO FOR D35K ALTERNATE LG4680R-B005A MOTOR(MECH)
  • Page 77 VHR-VK310A(SANYO) AUSTRALIA AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS LG4470R-0100A GEAR RACK F/L 054A LG4970R-0124B SPRING COIL D35 (RACK F/L) LG4470R-0097A GEAR DRIVE(D35) LG4470R-0096A GEAR CAM(D35) LG4510R-0040A LEVER F/R(D35) LG4265R-0005A CLUTCH ASSEMBLY D35 (M) LG4470R-0098A GEAR SECTOR(D35) LG4261R-0021A ARM ASSY...
  • Page 78 NOTES) With respect to risk of fire or NOTES) electricial shock. SECTION 5 REPLACEMENT PARTS LIST SANYO MODEL : VHR-VK310A/NZ(SANYO) NEW ZEALAND NSP : Not available as service parts. RUN DATE :19-SEPTEMBER-03 S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION...
  • Page 79 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C115 LG624-085D CAPACITOR CE 47UF/50V KME (SMPS) C116 LG0CE108BF630 CAPACITOR,FIXED ELECTROLYTIC 1000UF KME 16V M FM5 BULK C117 LG0CE3376D638 CAPACITOR,ELECTROLYTIC 330UF SMS 10V M FM5 TP5 C120 LG0CE477BH630 CAPACITOR,AL.ELECTROLYTIC...
  • Page 80 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C341 LG0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S C342 LG0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA C343 LG0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V)
  • Page 81 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C561 LG0CE1064F638 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5) C566 LG0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V TA26 C567 LG0CN1020K518 CAPACITOR TUBULA(HIGH DIELE) 1000P 50V TA26 C568 LG0CN1020K518 CAPACITOR TUBULA(HIGH DIELE)
  • Page 82 IC102 LG6500RDB010A SENSOR PC123YN2 SHARP PHOTOCOUPLER ALTERNATE IC103 LG0IKE431000A IC,KEC KIA431 3 PIN TP IC301 LG0ILNRSA006B IC,LINEAR LA71730EM SANYO 100PIN QFP TRA IC501 LG0IMCRMI026E IC,MICRO CONTROLLER M37762MCA-1M0GP MITSUBISHI 100 IC503 LG0IAL241600B IC,ATMEL AT24C16 - - - - IC503 LG0ICS241600B IC,CATALYST...
  • Page 83 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS L501 LG0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP L510 LG0LR0682K035 INDUCTOR RADIAL LEAD 68M K 6X6 L5 TP L511 LG0LR0221J0N5 INDUCTOR,RADIAL LEAD 2.2UH 5% TP 3X5 TR5...
  • Page 84 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS Q504 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ALTERNATE Q504 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ALTERNATE Q504 LG0TR319909AF TRANSISTOR,BIPOLARS KTC3199-BL MINI TP KEC Q506 LG0TR120109AC TRANSISTOR SRC1201 TP AUK TO92 4.7K,4.7K...
  • Page 85 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R315 LG0RD0472F608 RESISTOR,FIXED CARBON FILM 47 OHM 1/6 W 5% TA26 R317 LG0RD5601F608 RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5% TA26 R318 LG0RD3901F608 RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5% TA26...
  • Page 86 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R529 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26 R531 LG0RD4701F608 RESISTOR,FIXED CARBON FILM 4.7K OHM 1/6 W 5% TA26 R532 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26...
  • Page 87 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R5S1 LG0RD5601F608 RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5% TA26 R704 LG0RD1201F608 RESISTOR,FIXED CARBON FILM 1.2K OHM 1/6 W 5% TA26 R705 LG0RD1201F608 RESISTOR,FIXED CARBON FILM 1.2K OHM 1/6 W 5% TA26...
  • Page 88 RACK F/L LG4261R-0023A ARM ASSY LG4510R-0046A LEVER ASSY SWITCH LG6723R-0304B DRUM(CIRC) ASSEMBLY SUB D35-2CH (8M2) LG4680R-B008A MOTOR(MECH) DRUM VH4302-800 SANYO FOR D35K LG4680R-B010A MOTOR(MECH) DRUM MDVC-035KA LGIT FOR D35K ALTERNATE LG4680R-B009A MOTOR(MECH) DRUM I2OAL21 SANKYO FOR D35K ALTERNATE LG4680R-B005A MOTOR(MECH)
  • Page 89 VHR-VK310A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS 052A LG4980R-0023A SUPPORTER CAPSTAN(D35) LG4470R-0100A GEAR RACK F/L 054A LG4970R-0124B SPRING COIL D35 (RACK F/L) LG4470R-0097A GEAR DRIVE(D35) LG4470R-0096A GEAR CAM(D35) LG4510R-0040A LEVER F/R(D35) LG4265R-0005A CLUTCH ASSEMBLY D35 (M)
  • Page 90 Parts that are shaded are critical NOTES) With respect to risk of fire or NOTES) electricial shock. SECTION 5 REPLACEMENT PARTS LIST SANYO MODEL : VHR-VK910A(SANYO) AUSTRALIA NSP : Not available as service parts. RUN DATE :19-SEPTEMBER-03 S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION...
  • Page 91 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C115 LG624-085D CAPACITOR CE 47UF/50V KME (SMPS) C116 LG0CE108BF630 CAPACITOR,FIXED ELECTROLYTIC 1000UF KME 16V M FM5 BULK C117 LG0CE3376D638 CAPACITOR,ELECTROLYTIC 330UF SMS 10V M FM5 TP5 C120 LG0CE477BH630 CAPACITOR,AL.ELECTROLYTIC...
  • Page 92 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C341 LG0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S C342 LG0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA C343 LG0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V)
  • Page 93 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C553 LG0CQ3332K409 CAPACITOR,FIXED FILM 0.033UF S 50V J PE TP C554 LG0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S C561 LG0CE1064F638 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5)
  • Page 94 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C716 LG0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 C720 LG0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 C751 LG0CE4764C638 CAPACITOR,ELECTROLYTIC 47M SRA 6.3V M FM5 TP(5)
  • Page 95 IC102 LG6500RDB010A SENSOR PC123YN2 SHARP PHOTOCOUPLER ALTERNATE IC103 LG0IKE431000A IC,KEC KIA431 3 PIN TP IC301 LG0ILNRSA006B IC,LINEAR LA71730EM SANYO 100PIN QFP TRA IC501 LG0IMCRMI026E IC,MICRO CONTROLLER M37762MCA-1M0GP MITSUBISHI 100 IC503 LG0IAL241600B IC,ATMEL AT24C16 - - - - IC503 LG0ICS241600B IC,CATALYST...
  • Page 96 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS L314 LG0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP L501 LG0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP L510 LG0LR0682K035 INDUCTOR RADIAL LEAD 68M K 6X6 L5 TP...
  • Page 97 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS Q504 LG0TR319909AF TRANSISTOR,BIPOLARS KTC3199-BL MINI TP KEC Q504 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ALTERNATE Q504 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ALTERNATE Q506 LG0TR120109AC TRANSISTOR SRC1201 TP AUK TO92 4.7K,4.7K...
  • Page 98 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R315 LG0RD0472F608 RESISTOR,FIXED CARBON FILM 47 OHM 1/6 W 5% TA26 R317 LG0RD5601F608 RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5% TA26 R318 LG0RD3901F608 RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5% TA26...
  • Page 99 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R533 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26 R534 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26 R541 LG0RD2201F608 RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5% TA26...
  • Page 100 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R707 LG0RD5600F608 RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5% TA26 R753 LG0RD1001F608 RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5% TA26 R754 LG0RD3301F608 RESISTOR,FIXED CARBON FILM 3.3K OHM 1/6 W 5% TA26...
  • Page 101 LG4931R-0047A HOLDER ASSY LG4261R-0023A ARM ASSY LG4510R-0046A LEVER ASSY SWITCH LG6723R-0306C DRUM(CIRC) ASSEMBLY SUB D35-6CH (8P6C) LG4680R-B008A MOTOR(MECH) DRUM VH4302-800 SANYO FOR D35K LG4680R-B010A MOTOR(MECH) DRUM MDVC-035KA LGIT FOR D35K ALTERNATE LG4680R-B009A MOTOR(MECH) DRUM I2OAL21 SANKYO FOR D35K ALTERNATE LG4680R-B005A MOTOR(MECH)
  • Page 102 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS LG3041R-0037A BASE ASSY LG3041R-0038A BASE ASSY LG3041R-0039A BASE ASSY LG5870R-0005A OPENER LID(D35) LG3041R-0036A BASE ASSEMBLY A/C HEAD (ALPS) LG4408R-0003A REEL LG4970R-0140A SPRING COIL RS D35 LG4421R-0008A BRAKE ASSEMBLY LG4970R-0128A SPRING...
  • Page 103 VHR-VK910A(SANYO) AUSTRALIA S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS LG4930R-0276A HOLDER SIDE(L) LG4930R-0274A HOLDER LG4930R-0275A HOLDER SIDE(R) LG4510R-0044A LEVER STOPPER LG5870R-0004A OPENER DOOR LG4260R-0035A ARM F/L(L) LG3070R-0002A BODY LG4970R-0127A SPRING COIL D35 (F/L(R)) LG4260R-0036A ARM F/L(R) LG4510R-0042A LEVER...
  • Page 104 NOTES) With respect to risk of fire or NOTES) electricial shock. SECTION 5 REPLACEMENT PARTS LIST SANYO MODEL : VHR-VK910A/NZ(SANYO) NEW ZEALAND NSP : Not available as service parts. RUN DATE :19-SEPTEMBER-03 S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION...
  • Page 105 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C115 LG624-085D CAPACITOR CE 47UF/50V KME (SMPS) C116 LG0CE108BF630 CAPACITOR,FIXED ELECTROLYTIC 1000UF KME 16V M FM5 BULK C117 LG0CE3376D638 CAPACITOR,ELECTROLYTIC 330UF SMS 10V M FM5 TP5 C120 LG0CE477BH630 CAPACITOR,AL.ELECTROLYTIC...
  • Page 106 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C341 LG0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S C342 LG0CN1040K948 CAPACITOR,FIXED TUBULAR(High d 0.1UF D 50V 80%,-20% F(Y5V) TA C343 LG0CN4730K948 CAPACITOR,FIXED TUBULAR(High d 0.047UF D 50V 80%,-20% F(Y5V)
  • Page 107 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C553 LG0CQ3332K409 CAPACITOR,FIXED FILM 0.033UF S 50V J PE TP C554 LG0CN223AK948 CAPACITOR,TUBULAR(HIGH DIELEC) 0.022UF 50V Z F TA26 S C561 LG0CE1064F638 CAPACITOR,ELECTROLYTIC 10M SRA 16V M FM5 TP(5)
  • Page 108 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS C716 LG0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 C720 LG0CN1030F678 CAPACITOR TUBULA(HIGH DIELE) 0.01M 16V M Y TA26 C751 LG0CE4764C638 CAPACITOR,ELECTROLYTIC 47M SRA 6.3V M FM5 TP(5)
  • Page 109 IC102 LG6500RDB010A SENSOR PC123YN2 SHARP PHOTOCOUPLER ALTERNATE IC103 LG0IKE431000A IC,KEC KIA431 3 PIN TP IC301 LG0ILNRSA006B IC,LINEAR LA71730EM SANYO 100PIN QFP TRA IC501 LG0IMCRMI026E IC,MICRO CONTROLLER M37762MCA-1M0GP MITSUBISHI 100 IC503 LG0IAL241600B IC,ATMEL AT24C16 - - - - IC503 LG0ICS241600B IC,CATALYST...
  • Page 110 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS L314 LG0LA1000K018 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP L501 LG0LR1000K035 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP L510 LG0LR0682K035 INDUCTOR RADIAL LEAD 68M K 6X6...
  • Page 111 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS Q504 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ALTERNATE Q504 LG0TR534309BA TRANSISTOR 2SC5343-L TP AUK TO92 ALTERNATE Q504 LG0TR319909AF TRANSISTOR,BIPOLARS KTC3199-BL MINI TP KEC Q506 LG0TR120109AC TRANSISTOR SRC1201 TP AUK TO92 4.7K,4.7K...
  • Page 112 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R315 LG0RD0472F608 RESISTOR,FIXED CARBON FILM 47 OHM 1/6 W 5% TA26 R317 LG0RD5601F608 RESISTOR,FIXED CARBON FILM 5.6K OHM 1/6 W 5% TA26 R318 LG0RD3901F608 RESISTOR,FIXED CARBON FILM 3.9K OHM 1/6 W 5% TA26...
  • Page 113 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R533 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26 R534 LG0RD1002F608 RESISTOR,FIXED CARBON FILM 10K OHM 1/6 W 5% TA26 R541 LG0RD2201F608 RESISTOR,FIXED CARBON FILM 2.2K OHM 1/6 W 5% TA26...
  • Page 114 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS R707 LG0RD5600F608 RESISTOR,FIXED CARBON FILM 560 OHM 1/6 W 5% TA26 R753 LG0RD1001F608 RESISTOR,FIXED CARBON FILM 1K OHM 1/6 W 5% TA26 R754 LG0RD3301F608 RESISTOR,FIXED CARBON FILM 3.3K OHM 1/6 W 5% TA26...
  • Page 115 SUB D35-6CH (8P6C) LG4680R-B003B MOTOR(MECH) DRUM VH4301 KUMAGAYA DRUM MOTO ALTERNATE LG4680R-B009A MOTOR(MECH) DRUM I2OAL21 SANKYO FOR D35K ALTERNATE LG4680R-B008A MOTOR(MECH) DRUM VH4302-800 SANYO FOR D35K LG4680R-B010A MOTOR(MECH) DRUM MDVC-035KA LGIT FOR D35K ALTERNATE LG4680R-B007A MOTOR(MECH) DRUM MDVC-035AA LGIT FOR D-35, ALTERNATE...
  • Page 116 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS LG3041R-0037A BASE ASSY LG3041R-0038A BASE ASSY LG3041R-0039A BASE ASSY LG5870R-0005A OPENER LID(D35) LG3041R-0036A BASE ASSEMBLY A/C HEAD (ALPS) LG4408R-0003A REEL LG4970R-0140A SPRING COIL RS D35 LG4421R-0008A BRAKE ASSEMBLY...
  • Page 117 VHR-VK910A/NZ(SANYO) NEW ZEALAND S AL LOCA. NO. PART NO. DESCRIPTION SPECIFICATION REMARKS LG4930R-0276A HOLDER SIDE(L) LG4930R-0274A HOLDER LG4930R-0275A HOLDER SIDE(R) LG4510R-0044A LEVER STOPPER LG5870R-0004A OPENER DOOR LG4260R-0035A F/L(L) LG3070R-0002A BODY LG4970R-0127A SPRING COIL D35 (F/L(R)) LG4260R-0036A F/L(R) LG4510R-0042A LEVER SWITCH...
  • Page 118 SANYO Electric Co.,Ltd. Osaka, Japan September/'03...

This manual is also suitable for:

Vhr-vk910aVhr-vk910a/nzVhr-vk310a/nz

Table of Contents