Installation - Toshiba AW-DC1000CM Owner's Manual

Attaching the water inlet hose to the faucet
If you attach the water inlet hose completely, it may cause a water leakage.
Faucet shape Wall-mounted faucets are best.
Wall-mounted Movable
Square
shaped
faucet
faucet
The distance is needed
1.6 cm or more
Attaching the hose union
1 Push the lock lever of the water
inlet hose. Pulling the sleeve down,
lower the entire hose to disconnect the
hose union.
2 Check the diameter of the faucet.
When the faucet mouth is large,
loose the screws and remove the
inside ring to facilitate, attachment.
3 Loose 4 screws of the hose union,
push the hose union to the water
faucet.
4 Tighten the four screws evenly around
the faucet. In this time check the gap
is approx. 4 mm between the nozzle
and the ring.
Connecting the water inlet hose
1 Pull the sleeve down, then insert
the water inlet hose.
2 Separate the sleeve until a click is
heard, then push it up.
3 Check to ensure that the lock
lever is hung on the nozzle. Next,
check to ensure that the water
inlet hose does not come off by
pulling down on it.
The water inlet valve may be clogged by lees or grimes.
You should remove inlet hose
a
and clean valve filter by brush.
If you remove the water supply
a
carelessly, water may splash.
Therefore, use the following
procedure.
Drain all water from the
basket, drainage hose
and water inlet hose
after using the machine.

INSTALLATION

Caution
•
The old inlet hose should not be reused.
•
Multi-home
If the faucets are not suited, please contact your dealer.
faucet
•
Do not connect the hot water supplying convenience.
•
In order to provide a permanent source of water
for your washing machine, it is suggested
that a branching water pipe (available separately)
be used.
Hose Union
 
Lock
lever
Water
inlet
hose
Ring
Approx.
4 mm.
Joint
seal
4 Tighten the hose nut
Nozzle
Lock
lever
②
①
Hose nut
Sleeve
Water inlet valve
If the filling water becomes not good
Inlet hose
Valve filter
Water inlet valve
In case of water may freeze
If the water is frozen
1 Remove the water inlet hose and pour in warm water (under 40°C).
2 Fill warm water (under 40°C) into the basket until the pulsator is
completely covered. Leave it for 30 minutes. Then check to see whether
the pulsator can be turned by hand.
5 Remove the seal from the union
and turn to the arrow destination
the nozzle to tighten securely.
6 Check the gap is approx. 1 to
Sleeve
3 mm between the nozzle and
the ring.
•
If the gap is wide, it may cause the water leak.
Inside
•
ring
If it cause the water leakage during operation,
tighten the nozzle more securely.
Caution
•
If you attach the hose union again because of
moving house etc., loose the gap is approx. 4 mm
between the nozzle and the
ring. Then attach it according
a b ove m e t h o d s. T h ey a re
preventable the water leakage.
Caution:
•
on the end of the
Check to ensure that the water inlet
water inlet hose
hose is properly installed by turning the
securely to the water
water on and checking for leakage.
inlet valve.
If there is leakage, connect it from the
first.
Inlet hose •
If you remove the water inlet hose
after supplying water, water may splash.
Refer to the following "Removing the
water inlet hose" .
Removing the water inlet hose
1 Turn off the water faucet.
2 Press the
Hose nut
machine then press the
3 After water level indicator will light up,
press the
4 Loosen the hose nut and then remove inlet hose.
Branching
water pipe
Hose union
Ring
button to open the washing
button.
button.
under 40°C
Approx.
1 to 3 mm
Nozzle
Approx.
4 mm
31