Related Manuals for ASROCK IMB-142
Summary of Contents for ASROCK IMB-142
-
Page 1: User Manual
IMB-142 User Manual Version 1.0 Published June 2013 Copyright©2013 ASRock INC. All rights reserved. -
Page 2: Copyright Notice
ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warran- ties or conditions of merchantability or fitness for a particular purpose. -
Page 3: Table Of Contents
Contents 1 Introduction ............5 1.1 Package Contents ............5 1.2 Specifications ..............6 1.3 Motherboard Layout ............7 1.4 I/O Panel ............... 8 2 Installation ............9 2.1 Screw Holes ..............9 2.2 Pre-installation Precautions ........... 9 2.3 Installation of Memory Modules (DIMM) ......10 2.4 Expansion Slot .............. -
Page 4: Introduction
In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. -
Page 5: Specifications
1.2 Specifications Form Dimensions - Mini-ITX (6.7-in x 6.7-in) Factor ® - Intel Dual-Core Atom™ CedarView Processor D2550/N2600/N2800 - Supports Hyper-Threading Technology Core Processor Number System - D2550/N2800: 1.86 GHz Max Speed - N2600: 1.6GHz L3 Cache - N/A Chipset - NM10 BIOS - UEFI... - Page 6 Max Data SATA Transfer - SATA2 (3.0Gb/s) Rate - 1 (DVI-D) HDMI DisplayPort - 0 Rear I/O Ethernet - 2 (USB 2.0 compliant) Audio - 2 (Mic-in, Line-out) Serial PS/2 - 6 (USB 2.0 compliant) LVDS/ - 1/0 Inverter Serial - 2 (RS-232) SATA - 2 x SATA2 (3.0Gb/s)
-
Page 7: Motherboard Layout
1.3 Motherboard Layout 17.0cm (6.7 in) JCF PWR1 ErP/EuP Ready CPU_FAN1 CHA_FAN2 CHA_FAN1 VGA1 CON1 PCIE1 LVDS1 USB 2.0 T: USB0 B: USB1 SMBUS1 SATAII_1 SATAII_2 16Mb BIOS Super COM2 USB4_5 USB6_7 PLED PWRBTN JPWR1 USB2_3 HDLED RESET JGP IO1 COM1 SATAPWR1 PANEL 1... -
Page 8: I/O Panel
1.4 I/O Panel Line out (Lime) USB 2.0 Ports (USB01) Microphone (Pink) DVI-D Port (DVI1) LAN RJ-45 Port HDMI Port (HDMI1) LAN RJ-45 Port * There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications. -
Page 9: Installation
Chapter 2: Installation This is a Mini-ITX form factor (6.7" x 6.7", 17.0 x 17.0 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. -
Page 10: Installation Of Memory Modules (Dimm)
2.3 Installation of Memory Modules (SO-DIMM) This motherboard provides two 204-pin DDR3 (Double Data Rate 3) SO-DIMM slots. It is not allowed to install a DDR or DDR2 memory module into DDR3 slot; otherwise, this motherboard and SO-DIMM may be damaged. Installing a SO-DIMM Please make sure to disconnect power supply before adding or removing SO-DIMMs or the system components. -
Page 11: Expansion Slot
2.4 Expansion Slots (PCI and mini-PCIe Slots) There is 1 PCI slot and 1 mini-PCIe slot on this motherboard. PCI Slot: PCI slot is used to install expansion cards that have the 32-bit PCI interface. PCIE Slot: MINI_PCIE1 (mini-PCIe slot) is used for PCI Express mini cards. Installing an expansion card Step 1. -
Page 12: Jumpers Setup
2.5 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”... -
Page 13: Onboard Headers And Connectors
2.6 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! SATAII Connectors These two Serial ATAII (SATAII) connectors support (SATAII_1: see p.7, No. - Page 14 RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating.
- Page 15 ATX 12V Power Connector Please connect an ATX 12V power supply to this connector. (4-pin ATX12V1) (see p.7 No. 2) Serial port Headers Each COM1 header supports a serial port module. (9-pin COM1) (see p.7 No. 24) (9-pin COM2) (see p.7 No. 25) JCF Power Connector (3-pin JCF PWR1) (see p.7 No.
-
Page 16: Smbus Connector
SMBUS Connector (2-pin SMBUS1) (see p.7 No. 9) LVDS Connector LVDS Connector Pin Definition (30-pin LVDS1) Pin 1, 2, 3, 4 : Backlight PWR (see p.7 No. 27) Pin 5, 6, 11, 17, 18, 29, 30 : GND Pin 7, 9 : LCD VDD PWR Enable Pin 8 : LCD PID1 Pin 10 : LCD PID0 Pin 12 : EDID CLK...