Panasonic WV-CF224 Service Manual
Panasonic WV-CF224 Service Manual

Panasonic WV-CF224 Service Manual

Color cctv camera
Hide thumbs Also See for WV-CF224:

Advertisement

SPECIFICATIONS

The Product with PbF
Pick-up device:
Scanning area:
Synchronization:
Scanning system:
Scanning:
Horizontal:
Vertical:
Horizontal resolution:
Video output:
Automatic Gain Control (AGC):
Automatic Tracing White Balance (ATW): ON only
Signal-to-noise ratio:
Minimum illumination:
Back Light Compensation (BLC):
Detail:
Lens:
Focal length:
F number:
Panning range:
Tilting range:
Azimuth range:
Ambient operating temperature:
Ambient operating humidity:
Power source and
power consumption:
Dimensions:
Weights:
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
768 (H) x 492 (V) pixels, interline transfer CCD
3.6 (H) x 2.7 (V) mm (equivalent to scanning area of 1/4" pick-up tube)
Internal, Line-lock (24 V AC only) or multiplexed vertical drive (VD2), selectable
2 : 1 interlace
525 lines / 60 fields / 30 frames
15.734 kHz
59.94 Hz
480 lines
1.0 V[p-p] NTSC composite 75 Ω
+18 dB
50 dB (equivalent to AGC Off, weight On)
2.0 lx (0.2 foot-candle) at F1.4 (WIDE)
On or Off
Sharp or Soft, selectable
2x variable focal lens
f=2.8 - 6.0 mm
F1.4 - 1.8, close
±100 °
±75 °
±100 °
–10 °C to +50 °C (14 °F to 122 °F)
Less than 90 %
12 V DC, 235 mA
24 V AC 60 Hz, 2.8 W
ø135 mm x 90 mm (H)
ø 5-5/16" x 3-9/16" (H)
0.46 kg (1.01 lbs.)
R
Color CCTV Camera
WV-CF224
2 0 0 3
M a t s u s h i t a E l e c t r i c I n d u s t r i a l C o . , L t d .
A l l r i g h t s r e s e r v e d . U n a u t h o r i z e d c o p y i n g a n d
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
ORDER NO. AVS0309513C1
S02

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic WV-CF224

  • Page 1: Specifications

    ORDER NO. AVS0309513C1 Color CCTV Camera WV-CF224 SPECIFICATIONS The Product with PbF Pick-up device: 768 (H) x 492 (V) pixels, interline transfer CCD Scanning area: 3.6 (H) x 2.7 (V) mm (equivalent to scanning area of 1/4" pick-up tube) Synchronization:...
  • Page 2: Standard Accessories

    Y WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians.
  • Page 3: Table Of Contents

    CONTENTS MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ............1-1 ADJUSTMENT PROCEDURE ......................2-1 WIRING DIAGRAM ..........................3-1 SCHEMATIC DIAGRAM SENSOR BOARD ...........................4-1 MAIN BOARD ..........................4-2 SW BOARD ............................4-3 POWER BOARD ..........................4-4 CONDUCTOR VIEW SENSOR BOARD ...........................5-1 MAIN BOARD ..........................5-2 SW BOARD.............................5-3 POWER BOARD ..........................5-4 EXPLODED VIEW (1/3) ..............................6-1...
  • Page 4: Major Operating Controls And Their Functions

    MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS q Camera Panel SHARP* SOFT w Pan/Tilt/Azimuth Table Adjusts the panning/tilting and azimuth angle of the cam- OFF* era. SYNC INT* e Focus Lever i Aperture Level Selector Fixes the focus position after adjusting. SHARP: Sharpens the image outline.
  • Page 5: Adjustment Procedure

    1. Test Equipment Required Adjustment The following Test Equipment is required for Adjustment of the Color CCTV Camera WV-CF224. 8 Referring to Fig. 2-1, remove the Rubber Cap from the 8 Oscilloscope Panel Cover Ass'y, and remove one screw that secures 8 Digital Voltmeter the Panel Cover Ass'y.
  • Page 6 8 Referring to Fig. 2-3, remove two screws and three washers 8 Referring to Fig. 2-5, remove two screws that secure the that secure the Main Unit, and remove the Main Unit from Main Board, disconnect the Connector CN1 on the Main the Camera Unit.
  • Page 7 3. Connection and Setting Up for (2). Installing E.V.R. Adjustment Program Adjustment 8 Make a copy of following necessary files to your comput- 3.1. Connection er from original floppy disk of the E.V.R. Adjustment Kit. LADJ.EXE 8 The Fig. 3-1 shows the connection diagram for the CF224P.SEQ Adjustment Procedure.
  • Page 8 L301 (LL VCO) Sensor Board 8 Set the Synchronization Mode Selector (on the SW Board SW1) to LL position. PANASONIC REMOTE EVR ADJUSTMENT SYSTEM (C) MCI Co. CCTV PRODUCT:CF224 EEPROM:0 MENU Page (1/1) NTSC 8 Connect the Digital Voltmeter to TP1.
  • Page 9 (1). FSC Adjustment (5.1). OB Level Adjustment Test Point: Pin 3 of IC5 (28MHz) Sensor Board Test Point: Video Output Connector 8 Connect the terminated Oscilloscope with 75Ω to Video 8 Confirm that the Synchronization Mode Selector (on the Output Connector. SW Board SW1) is set to INT Position.
  • Page 10 (6). Burst Level Adjustment (7.3). 3200°K Phase Adjustment Test Point: Video Output Connector Test Point: Video Output Connector 8 Keep the Color Temperature at 3 200°K. 8 Keep the Color Temperature at 3 200°K. 8 Aim the Camera at the Logarithmic Gray Scale Chart. 8 Aim the Camera at the Color Chip Chart.
  • Page 11 (7.5). Color Center Point Adjustment (8.1). ATW Confirmation (Don't Change Data) Test Point: Video Output Connector 8 Press the ENTER key for next adjustment. 8 Keep the Color Temperature at 3 200°K. 8 Aim the Camera at the Color Chip Chart. (8.2).
  • Page 12: Wiring Diagram

    WIRING DIAGRAM POWER BOARD SW BOARD MAIN BOARD (LL VCO) SENSOR BOARD VIDEO OUTPUT CABLE (28MHz) POWER CABLE VIDEO OUTPUT CONNECTOR L301 (LL VCO) OPTICAL ASS'Y (IC1) LENS (M20)
  • Page 13 SCHEMATIC DIAGRAM OF SENSOR BOARD SENSOR BOARD <INDEX> SENSOR Note BOARD • IC1 (Optical Ass'y) is not included in the Sensor Board Ass'y. AGC CONT D2,D3 AMP GAIN OB CONT B2,B3 B3,B4, C3,C4 B4,B5, C4,C5 V-DRIVER R203 0R00 IC301 C202 L301 C1,D1 OSUB...
  • Page 14 SCHEMATIC DIAGRAM OF MAIN BOARD MAIN BOARD <INDEX> MAIN BOARD 4.7/25 FWHD 1/25 DC-DC OPEN OPEN C4,D4 OPEN LP SYNC VCO) 3.3V OPEN OPEN OPEN OPEN CBLK OPEN COMMON VDD OPEN R100 OPEN OPEN 0R00 TD13 TD17 TD21 TD25 TD27 TD29 TD11 TD15...
  • Page 15 SCHEMATIC DIAGRAM OF SW BOARD SW BOARD VIDEO OUTPUT VIDEO CABLE (E1) VIDEO(I) (WITH VIDEO ALC/ELC VIDEO JACK OUTPUT VIDEO(O) CONNECTOR) NTSC : 0R00 PAL : 0R00 JAPAN : OPEN ALC/ELC SOFT/SHARP BLC ON/OFF INT/LL VIDEO(I) 0R00 3.3V LL DET 1-8 : SYNCHRONIZATION MODE SELECTOR(1) MAIN...
  • Page 16 SCHEMATIC DIAGRAM OF POWER BOARD POWER BOARD <INDEX> POWER (12V DC) (24V AC) BOARD LIVE – 3.15A NEUTRAL 250V POWER CABLE (E3) B3,C3 10.5V LLDET Attachment1 Attachment2 BOARD AGND Note: The value indicated in the schematic DGND diagram should be read as follows: <Example>...
  • Page 17 CONDUCTOR VIEW OF SENSOR BOARD SENSOR BOARD <INDEX> SENSOR BOARD (COMPONENT SIDE) A1,A2,B1,B2 IC301 A1,B1 D301 D302 D303 (COMPONENT SIDE) SENSOR BOARD <INDEX> SENSOR BOARD (PATTERN SIDE) A1,A2 A1,A2,B1,B2 (PATTERN SIDE)
  • Page 18 CONDUCTOR VIEW OF MAIN BOARD MAIN BOARD <INDEX> MAIN BOARD (COMPONENT SIDE) A1,A2 B1,B2 (COMPONENT SIDE) MAIN BOARD <INDEX> MAIN BOARD (PATTERN SIDE) (PATTERN SIDE)
  • Page 19 CONDUCTOR VIEW OF SW BOARD SW BOARD <INDEX> SW BOARD (COMPONENT SIDE) (COMPONENT SIDE)
  • Page 20 CONDUCTOR VIEW OF POWER BOARD POWER BOARD POWER BOARD (COMPONENT SIDE) (PATTERN SIDE) <INDEX> <INDEX> POWER BOARD POWER BOARD (COMPONENT SIDE) (PATTERN SIDE) A1,B1 A1,B1...
  • Page 21: Exploded View

    EXPLODED VIEW (1/3) PACKAGING WV-CF224 Camera Unit (Refer to the page 6-2.) Bar Code Label...
  • Page 22: Camera Unit

    EXPLODED VIEW (2/3) Numbers show screws and washers. Screws Description XYN2+J4FN Pan Head Machine Screw and Washer Ass'y XSS26+5FN Flush Head Machine Screw XSB3+5FZK Binding Head Machine Black Screw XXE2D3FZK Binding Head Machine Black Screw Camera Unit Main Unit (Refer to the page 6-3.) Power Unit (Refer to...
  • Page 23: Main Unit

    EXPLODED VIEW (3/3) Numbers show screws and washers. Screws Description XTB2+6GFX Binding Head Tapping Screw XYN2+J5FN Pan Head Machine Screw and Washer Ass'y XYN26+J5FN Pan Head Machine Screw and Washer Ass'y XYN26+F9FZK Pan Head Machine Black Screw and Washer Ass'y XSB3+5FN Binding Head Machine Screw Main Unit...
  • Page 24: Replacement Parts List

    REPLACEMENT PARTS LIST Important Notice Components identified by " Y " mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts. RTL : Retention Time Limited (No longer available after discontinuing product). REF.
  • Page 25 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION ERJ3GEYJ201V Metal 200 ohms 1/16W ECST1AY106R Tantalum 10 µF 10V ERJ3RHD201V Metal 200 ohms 1/16W MCUV1E104ZFV Ceramic 0.1 µF ERJ3GEYJ102V Metal 1K ohms 1/16W F1H1A105A004 Ceramic 1 µF ERJ3GEYJ222V Metal 2.2K ohms 1/16W F3H1A476A001 Tantalum...
  • Page 26 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION ERJ3GEYJ220V Metal 22 ohms 1/16W F1H1H222A013 Ceramic 2200 pF ERJ3GEYJ222V Metal 2.2K ohms 1/16W F1H1H103A190 Ceramic 0.01 µF ERJ3GEYJ154V Metal 150K ohms 1/16W F1H1A105A004 Ceramic 1 µF ERJ3RHD102V Metal 1K ohms 1/16W MCUV1E104ZFV Ceramic 0.1 µF...
  • Page 27 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION G0ZZ00002012 Coil 33 µH POWER BOARD YWSL675330 Coil 33 µH G4D1A0000050 Power Transformer PCB4 (RTL) VCF22PKY4A Printed Circuit Board Ass'y K5G312B00010 Current Fuse 3.15A 250V AN1431ME1 Shunt Ragulator YWB3BPHKS 3-pin Connector B1DFGM000001 Q2,3 YWPC817X7...

Table of Contents