Page 1
* Refer to parts list on page 20. In compliance with Federal Regulations, following are repro- KENWOOD Corp. certifies this equipment conforms to DHHS duction of labels on, or inside the product relating to laser Regulations No.21 CFR 1040. 10, Chapter 1, subchapter J.
(Accessory only for regions where use is necessary.) SYSTEM CONFIGURATION SYSTEM RECEIVER SPEAKERS HM-537MP-H RXD-M57MP-H LS-M57-H HM-537MP-S RXD-M57MP-S LS-M57-S CAUTIONS Resetting the Microcomputer The microcomputer may malfunction (unit can- CLASS 1 LASER PRODUCT...
RXD-M57MP EXTERNAL VIEW FM 75 ohm Ant. (E70-0200-08) Top cabinet (A01-3943-08) Rear cabinet (A80-4494-08) VOLTAGE SELECTOR 110-120V Voltage SW. * (S62-0124-08) 220-240V * Refer to parts list on page 20.
Page 4
RXD-M57MP ADJUSTMENT SERVICE ADJUSTMENT Lubrication The mechanical parts are factory coated with a thin coat of light grease and should not require further lubrication. If a light grease is applied, be careful not to get any grease on the play/record head or erase head, hubs, pulleys, tapes reels, drive belts, or switches.
RXD-M57MP ADJUSTMENT 2. Insert a 10 kHz test tape (Teac MTT-1141V or Equivalent) into the tape mechanism and play it back. 3. While playing back the test tape, slowly turn the azimuth adjusting screw until the amplitude of both channel output waveforms is maximum and in phase. Note: Reiteration adjusting Right, lift the screw, until the amplitude of both channel output waveform is maximum.
Page 6
RXD-M57MP ADJUSTMENT TUNER ALIGNMENT PROCEDURE Equipment needed: 1. AM Signal generator 2. FM Signal generator 3. DC Voltage meter 4. Oscilloscope 5. Output meter (VTVM) AM Alignment Step S/G Frequency Dial Setting Indicator Adjust Remarks 450 kHz (1 kHz 30% mod.) 612 kHz Connect T101...
Page 7
RXD-M57MP ADJUSTMENT FM Alignment: TEST UNIT GROUND Figure 5. FM Band Frequency Coverage Alignment Connect FM S/G to ANT inputs (mod 1 kHz 22.5kHz dev.) Step S/G Frequency Dial Setting Indicator Adjust Remarks 87.5 MHz Low end Connec t DC Voltage Confirm Vt: 1.7 ±...
Page 8
PC BOARD (Component side view) CN501 HEADPHONE CN403 L405 L406 L408 JK400 R521 R520 R500 R519 R517 R518 R524 R509 R510 JACK2 R511 R508 R507 R506 R505 R504 R503 R522 R501 R502 R523 R512 Refer to the schematic diagram for the value of resistors and capacitors.
Page 12
RXD-M57MP MAIN The DC voltage is an actual reading FP101 measured with a high impedance +12V +12V type voltmeter with no signal input. R108 IC103 R128 Q107 R133 The measurement value may vary C173 3.3K R107 R172 330 R129 RCLK depending on the measuring instru- C111 L104...
Page 13
RXD-M57MP COM/PIN # DISPLAY COM-0 COM0 COM-1 COM1 LCD601 COM-2 COM2 CAUTION: For continued COM-3 COM3 safety, replace safety critical components only with manu- COM/PIN # facturer's recommended parts COM-0 (refer to parts list). indicates F H I safety critical components. COM-1 For continued protection COM-2...
Page 15
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 16
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 17
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 18
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 19
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 20
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
........ 87.5 MHz ~ 108 MHz AM tuner section Notes: Tuning frequency range KENWOOD follows a policy of continuous (For the Europe and Australia) advancements in development. For this reason ......... 531 kHz ~ 1,602 kHz specifications may be changed without notice.