Page 1 TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior and Air conditioning and audio systems, as well as other in- exterior features terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
Page 2: For Your Information
Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 3 ● Anti-lock brake system ● SRS airbag system ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. Vehicle data recordings Your Toyota is equipped with several sophisticated computers that will record certain data, such as: •...
Page 4: Event Data Recorder
Event data recorder This vehicle is equipped with an event data recorder (EDR). The main pur- pose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
Page 5 ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehicle) is obtained • In response to an official request by the police, a court of law or a govern- ment agency •...
Page 6 CAUTION General precautions while driving ■ Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 7 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 8 Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 432)
Page 9 1-1. Key information NOTICE To prevent key damage (vehicles with engine immobilizer system) ■ Do not subject the keys to strong shocks, expose them to high tempera- ● tures by placing them in direct sunlight, or get them wet. Do not expose the keys to electromagnetic materials or attach any mate- ●...
Page 10 1-2. Opening, closing and locking the doors ∗ Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
Page 11 Pressing a button may cause the wireless remote control to emit radio waves that could inter- fere with the operation of the aircraft. Customization that can be configured at Toyota dealer ■ Settings (e.g. wireless remote control system) can be changed.
Page 12 1-2. Opening, closing and locking the doors Certification for wireless remote control ■ MODEL/FCC IDs: Transmitter: GQ43VT20T Receiver: GQ4-34R IC (Canada) IDs: Transmitter: 1470A-1T Receiver: 1470A-6R MADE IN U.S.A. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Page 13 1-2. Opening, closing and locking the doors Side doors The vehicle can be locked/unlocked using the wireless remote con- trol, key or door lock switch. Wireless remote control (if equipped) ■ →P. 34 ■ Regular Cab models Locks the door Unlocks the door Access Cab and Double Cab models Locks all doors...
Page 14 1-2. Opening, closing and locking the doors Door lock switch (if equipped) ■ Driver’s door lock switch Locks all doors Unlocks all doors Passenger’s door lock switch Locks all doors Unlocks all doors Inside door lock button ■ Locks the door Unlocks the door Pulling the inside handle can open the front door even if the...
Page 15 1-2. Opening, closing and locking the doors Locking the front doors from the outside without a key Move the inside door lock button to the lock position. Close the door. Vehicles with power door lock system The door cannot be locked if a front door is open and the key is in the engine switch.
Page 16 1-2. Opening, closing and locking the doors CAUTION To prevent an accident ■ Observe the following precautions while driving the vehicle. Failing to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. Always use a seat belt.
Page 17 1-2. Opening, closing and locking the doors Access doors (Access Cab models only) The access door (rear door) can be opened using the inside handle. Open the front door widely Pull (from the outside) or push (from the inside) the inside handle of the access door.
Page 18 1-2. Opening, closing and locking the doors Tailgate The tailgate can be opened. Pull the handle Open the tailgate slowly The support cables will hold the tailgate horizontal. After closing the tailgate, try pulling it toward you to make sure it is securely locked. Removing the tailgate Before removing the tailgate (vehicles with rear view monitor ■...
Page 19 1-2. Opening, closing and locking the doors To disconnect the wire harness connectors ( ), press and hold the lock of the tailgate wire harness connector (White) and pull apart. Tailgate wire harness connec- tor (White) Frame wire harness connector (Gray) Attach connector...
Page 20 1-2. Opening, closing and locking the doors Pull out the wire harness from the vehicle bed. Attach connector cover (Gray) to the tailgate wire har- ness connector (White). Tailgate wire harness connec- tor (White) Connector cover (Gray) Removing the tailgate ■...
Page 21 1-2. Opening, closing and locking the doors Slide the tailgate a little to the right to unhook the left side. To attach the tailgate, follow the removal procedure in reverse order. Rear step bumper For rear end protection and eas- ier step-up loading.
Page 22 1-2. Opening, closing and locking the doors NOTICE To prevent damage to the tailgate wire harness (vehicles with rear view ■ monitor system) Do not pull out all of the tailgate wire harness before open the tailgate. To prevent damage to the camera lens (vehicles with rear view monitor ■...
Page 23 1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Bench type seat Seat position adjustment lever Separated type seats Seat position adjustment lever Driver’s seat lumbar sup- port adjustment knob (if equipped) Seatback angle adjustment lever...
Page 24 1-3. Adjustable components (seats, mirrors, steering wheel) Moving passenger’s seat for rear seat entry (if equipped) Lift the seatback angle adjusting lever or press the pedal behind the seatback. The seat will slide forward. Move the seat to the front-most position.
Page 25 1-3. Adjustable components (seats, mirrors, steering wheel) Folding passenger’s seat (vehicles with seatback table) Pull the seatback angle adjusting lever and raise the seatback to its upright position. Pull the seatback folding lever and fold the seatback down.
Page 26 1-3. Adjustable components (seats, mirrors, steering wheel) Active head restraints (Access Cab and Double Cab models only) When occupant’s back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward to help reduce the risk of whiplash on the seat occupant.
Page 27 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Seat adjustment ■ Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion ● to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 28 1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats (Access Cab and Double Cab models) Access Cab models The bottom cushion of the rear seats can be raised and lowered. Before raising the bottom cushion ■ Stow the seat belt buckles. This prevents the seat belt buckles from falling out when you fold the seatback.
Page 29 1-3. Adjustable components (seats, mirrors, steering wheel) Double Cab models The seatback of the rear seat can be folded. Before folding rear seats ■ Stow the rear seat belt buck- les. This prevents the seat belt buckles from falling out when you fold the seatback.
Page 30 1-3. Adjustable components (seats, mirrors, steering wheel) Attach the head restraints to the holders located on the back sides of the bottom cush- ions. Fold down the seatback by pulling the lock release strap. Waterproof and water-repellent seats (if equipped) ■...
Page 31 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION When the seatback is folded/the bottom cushion is raised ■ Do not sit on or place anything on the seatback or auxiliary box while driving. When returning the seats to their original position ■...
Page 32 1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Adjusting the head restraints ■ Bench type front seat Pull the head restraints up. Down Push the head restraint down while pushing the lock release button.
Page 33 1-3. Adjustable components (seats, mirrors, steering wheel) When using the rear head restraints ■ Access Cab models To use Lift up the head restraint until it locks. To fold Pull the head restraint lock release lever to fold the head restraint.
Page 34 1-3. Adjustable components (seats, mirrors, steering wheel) Separated type seat Pull the head restraint up while pushing the lock release button. Removing the rear head restraints (Double Cab models only) ■ Pull the head restraint up while pushing the lock release button. Installing the front head restraints ■...
Page 35 1-3. Adjustable components (seats, mirrors, steering wheel) Installing the rear head restraints (Double Cab models only) ■ Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.
Page 36 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Head restraint precautions ■ Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. Use the head restraints designed for each respective seat. ●...
Page 37 1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. Correct use of the seat belts ■ ● Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
Page 38 1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of the belt (front seats) ■ Move the height adjuster up as needed until you hear a click. Down Push the lock release button and slide the height adjuster down. Center seat belt of the bench seat ■...
Page 39 1-3. Adjustable components (seats, mirrors, steering wheel) Emergency locking retractor (ELR) ■ The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Page 40 Each seat belt should be used by one person only. Do not use a seat belt ● for more than one person at once, including children. Toyota recommends that children be seated in the rear seat and always ● use a seat belt and/or an appropriate child restraint system.
Page 41 Ensure that the belt and tab are locked and the belt is not twisted. ● If the seat belt does not function correctly, immediately contact your Toyota dealer. Replace the seat assembly, including the belts, if your vehicle has been ●...
Page 42 Do not attempt to install, remove, modify, disassemble or dispose of the ● seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.
Page 43 1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and press the lever down. Adjust to the ideal position by moving the steering wheel horizontally and vertically. After adjustment, pull the lever up to secure the steering wheel.
Page 44 1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position...
Page 45 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror (type A) In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode on/off The indicator comes on when automatic mode is turned on.
Page 46 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror (type B) In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode on/off The indicator comes on when automatic mode is turned on.
Page 47 1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror display (vehicles with auto anti-glare inside rear view mirror) The inside rear view mirror displays the following information. Also, the display and display settings can be changed. Compass ■ →P.
Page 48 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Caution while driving ■ Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.
Page 49 1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted. Power-adjustable type Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down, in or out using the switch.
Page 50 1-3. Adjustable components (seats, mirrors, steering wheel) Manually adjustable type Adjust the mirror up, down, in or out by pushing the mirror surface. Folding back the mirrors Push backward to fold the mir- rors. Mirror operating conditions (vehicles with power-adjustable type only) ■...
Page 51 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION When driving the vehicle ■ Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. Do not adjust the mirrors while driving.
Page 52 1-4. Opening and closing the windows ∗ Power windows The power windows can be opened/closed using the following switches. Driver’s power window switches Closing Opening One-touch opening (driver’s window only) *: Pressing the switch in the opposite direction will stop win- dow travel partway.
Page 53 1-4. Opening and closing the windows The power windows can be operated when ■ The engine switch is in the ON position. Operating the power windows after turning the engine off ■ The power windows can be operated for approximately 43 seconds even after the engine switch is turned to the ACC or LOCK position.
Page 54 1-4. Opening and closing the windows Back window (vehicles with sliding type) The back window can be opened and closed using the lock release lever. Open/close Push the lock release lever and slide the back window. Closing the back window ■...
Page 55 1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. Before refueling the vehicle ■ Turn the engine switch off and ensure that all the doors and win- dows are closed. Opening the fuel tank cap ■...
Page 56 1-5. Refueling Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction. Fuel types ■ Use unleaded gasoline. (Octane Rating 87 [Research Octane Number 91] or higher) Fuel tank capacity ■...
Page 57 When replacing the fuel tank cap ■ Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 58 1-6. Theft deterrent system ∗ Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. The indicator light flashes after the key has been removed from the engine switch to indi-...
Page 59 1-6. Theft deterrent system Certifications for the engine immobilizer system ■ For vehicles sold in U.S.A. FCC ID: MOZRI-21BTY This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 60 1-6. Theft deterrent system For vehicles sold in New Caledonia “Hereby, Tokai Rika Co., Ltd., declares that this RI-21BTY is in compliance with the essential requirements and other rele- vant provisions of Directive 1999/5/EC.” NOTICE To ensure the system operates correctly ■...
Page 61 1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (→P. 47) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
Page 62 1-7. Safety information CAUTION While driving ■ Do not adjust the position of the driver’s seat while driving. ● Doing so could cause the driver to lose control of the vehicle. Do not place a cushion between the driver or passenger and the seatback. ●...
Page 63 1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and right front...
Page 64 1-7. Safety information Airbag system components Vehicles with bench type front seat Vehicles with separated type front seat...
Page 65 1-7. Safety information Front passenger airbag Side and curtain shield air- bag sensors Curtain shield airbags Driver’s seat position sen- Side airbags AIR BAG ON and AIR BAG Driver’s seat belt buckle OFF indicator lights switch warning light Front passenger’s seat belt RSCA OFF indicator light buckle switch (4WD models only)
Page 66 1-7. Safety information SRS warning light ■ This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensor assemblies, curtain shield air- bag sensor assemblies (Access Cab and Double cab models), driver’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system (ECU and sensors), AIR BAG ON and AIR BAG OFF indicator lights, front passenger’s seat position sensor (Bench type seat),...
Page 67 1-7. Safety information Depending on the type of collision, it is possible that only the seat belt ● pretensioners will activate. The SRS front passenger airbag will not activate if there is no passenger ● sitting in the front passenger seat. However, the front passenger airbag may deploy if luggage is put in the seat, even if the seat is unoccupied.
Page 68 1-7. Safety information The SRS curtain shield airbags may also deploy under the situation shown in the illustration. The angle of vehicle tip-up is marginal. ● The vehicle skids and hits a curb stone. ● Types of collisions that may not deploy the SRS airbag (front airbags) ■...
Page 69 1-7. Safety information Types of collisions that may not deploy the SRS airbag ■ (side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
Page 70 1-7. Safety information When to contact your Toyota dealer ■ In the following cases, contact your Toyota dealer as soon as possible. Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged or ●...
Page 71 1-7. Safety information CAUTION SRS airbag precautions ■ Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. The driver and all passengers in the vehicle must wear their seat belts ● properly. The SRS airbags are supplemental devices to be used with the seat belts.
Page 72 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are...
Page 73 1-7. Safety information CAUTION SRS airbag precautions ■ Do not sit on the edge of the seat or ● lean against the dashboard. Do not allow a child to stand in front of ● the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 74 Wash off any residue as soon as possible to prevent skin irritation. If the areas where the SRS airbags are stored, such as the steering wheel ● pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.
Page 75 Modification and disposal of SRS airbag system components ■ Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
Page 76 1-7. Safety information Deactivating the curtain shield airbags in a vehicle rollover (4WD models only) On/off (hold for a few seconds) The RSCA OFF indicator turns on (only when the engine switch is in the ON position.) The roll sensing function for the curtain shield airbags and seat belt pretensioners will turn back on automatically each time the...
Page 77 1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the right front passenger seat and activates or deactivates the devices for the front passenger.
Page 78 1-7. Safety information Conditions and operation of the front passenger occupant classification system Adult* ■ AIR BAG ON and AIR BAG OFF indica- AIR BAG ON tor lights Indicator/ SRS warning light warning light Front passenger’s seat belt reminder Flashing* light Front passenger airbag Side airbag on the front passenger seat...
Page 79 1-7. Safety information Unoccupied ■ AIR BAG ON and AIR BAG OFF indica- Not illumi- tor lights nated Indicator/ SRS warning light warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seat Devices Activated Curtain shield airbag in the front passen-...
Page 80 1-7. Safety information : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 106) : In case the indicator is not illuminated, consult this manual for installing the child restraint system properly.
Page 81 Do not kick the front passenger seat or subject it to severe impact. Other- ● wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. Child restraint systems installed on the rear seat should not contact the ●...
Page 82 1-7. Safety information Child restraint systems A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
Page 83 1-7. Safety information Forward facing — Convertible seat Booster seat Selecting an appropriate child restraint system ■ Use a child restraint system appropriate for the child until the child ● becomes large enough to properly wear the vehicle’s seat belt. If a child is too large for a child restraint system, sit the child on a rear ●...
Page 84 Regular Cab models: Toyota strongly urges use of a proper child restraint ● system which conforms to the size of the child. Access Cab and Double Cab models: Toyota strongly urges the use of a ● proper child restraint system that conforms to the size of the child, installed on the rear seat.
Page 85 1-7. Safety information CAUTION Child restraint precautions ■ Do not use the seat belt extender when installing a child restraint system ● on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or an accident.
Page 86 1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
Page 87 1-7. Safety information Using the seat belts ■ Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (→P. 61) Using the top tether strap ■ Regular Cab models with bench type seat Anchor bracket (for top tether strap) Anchor bracket is provided for each passenger seat.
Page 88 1-7. Safety information Regular Cab models with separated type seat Anchor bracket (for top tether strap) Anchor bracket is provided for passenger seat. Access Cab models Anchor bracket (for top tether strap) Anchor bracket is provided for each rear seat.
Page 89 1-7. Safety information Double Cab models Anchor bracket (for top tether strap) Anchor bracket is provided for each rear seat.
Page 90 1-7. Safety information Installation with LATCH system (Access Cab models) Type A Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor.
Page 91 1-7. Safety information Type B Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor. For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a lower connector system.
Page 92 1-7. Safety information Installation with LATCH system (Double Cab models) Type A Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched...
Page 93 1-7. Safety information Type B Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor. For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a...
Page 94 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
Page 95 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
Page 96 1-7. Safety information Booster seat ■ Place the booster seat on the seat facing the front of the vehi- cle. Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle.
Page 97 1-7. Safety information Child restraint systems with a top tether strap (Regular Cab models) Bench type seat ■ Remove the head restraint. Installing position: Right side passenger seat Center passenger seat Swing the seatback forward slightly (→P. 48) and remove the anchor bracket covers.
Page 98 1-7. Safety information Center passenger seat Route the top tether strap through the routing device as shown in the illustration. Make sure the top tether strap is not twisted. Latch the hook onto the anchor bracket. Return the seatback to its orig- inal position.
Page 99 1-7. Safety information Separated type seat ■ Remove the head restraint. Swing the seatback forward slightly (→P. 47) and remove the anchor bracket cover. Store the removed cover in a safe place such as the glove box. Route the top tether strap through the routing device as shown in the illustration.
Page 100 1-7. Safety information Replace the head restraint. Child restraint systems with a top tether strap (Access Cab models) Remove the anchor bracket cov- ers. Store the removed covers in a safe place such as the glove box. Secure the child restraint using a seat belt or lower anchors. Route the top tether strap through the routing device as shown in the illustration.
Page 101 1-7. Safety information Child restraint systems with a top tether strap (Double Cab models) Remove the head restraint. Installing position: Outside passenger seat Center passenger seat Outside passenger seat Swing the seatback forward slightly. (→P. 53) Latch the hook onto the anchor bracket.
Page 102 1-7. Safety information Secure the child restraint using a seat belt or lower anchors, and tighten the top tether strap. Make sure the top tether strap is securely latched. Replace the head restraint. Installing position: Outside passenger seat Center passenger seat Laws and regulations pertaining to anchorages ■...
Page 103 1-7. Safety information CAUTION When installing a booster seat ■ Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode. (→P. 63) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.
Page 104 1-7. Safety information CAUTION When installing a child restraint system ■ When a booster seat is installed, always ensure that the shoulder belt is ● positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
Page 105 2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. Starting the engine ■ →P. 141 Driving ■ Automatic transmission With the brake pedal depressed, shift the shift lever to D. (→P. 144) Release the parking brake.
Page 106 2-1. Driving procedures Parking the vehicle ■ Automatic transmission With the shift lever in D, depress the brake pedal. Set the parking brake. (→P. 152) Shift the shift lever to P. (→P. 144) When parking on a hill, if necessary, block the wheels. Turn the engine switch to the LOCK position to stop the engine.
Page 107 Breaking in your new Toyota ■ To extend the life of the vehicle, the following precautions are recommended...
Page 108 Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. On vehicles with an automatic transmission, do not shift the shift lever to P ●...
Page 109 2-1. Driving procedures CAUTION When driving the vehicle ■ Do not shift the shift lever to R while the vehicle is moving forward. ● Doing so can damage the transmission and may result in a loss of vehicle control. Do not shift the shift lever to D (vehicles with an automatic transmission) or ●...
Page 110 2-1. Driving procedures CAUTION When driving the vehicle ■ Do not drive in excess of the speed limit. Even if the legal speed limit per- ● mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires.
Page 111 2-1. Driving procedures CAUTION When the vehicle is stopped ■ If the vehicle is stopped on an incline, in order to prevent accidents caused ● by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed. Avoid revving or racing the engine.
Page 112 Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. Toyota does not recommend occupying the rear cargo area when it is fitted ● with a slide-in camper, camper shell or other type cover while the engine is running.
Page 113 2-1. Driving procedures CAUTION When braking the vehicle ■ Do not pump the brake pedal if the engine stalls. ● Each push on the brake pedal uses up the reserve for the power-assisted brakes. The brake system consists of 2 individual hydraulic systems: If one of the ●...
Page 114 If you hear a squealing or scraping noise while driving (brake pad wear ■ limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed.
Page 115 Engine damage caused by water immersion ● In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. Brake function ● Changes in quantity and quality of oil and fluid used for the engine, trans- ●...
Page 116 2-1. Driving procedures Engine (ignition) switch Engine switch ■ LOCK The steering wheel is locked and the key can be removed. (Vehicles with an automatic transmission: The key can be removed only when the shift lever is in P.) Some electrical components such as the audio system can be used.
Page 117 2-1. Driving procedures Turning the key from ACC to LOCK ■ Shift the shift lever to P (auto- matic transmission) or N (man- ual transmission). (→P. 144, 148) Push in the key and turn to the LOCK position. Steering lock release ■...
Page 118 2-1. Driving procedures CAUTION Caution while driving ■ Do not turn the engine switch to the LOCK position. If in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the ACC position. NOTICE To prevent battery discharge ■...
Page 119 2-1. Driving procedures ∗ Automatic transmission Select a shift position appropriate for the driving conditions. Shifting the shift lever ■ 5-speed models While the engine switch is on, depress the brake pedal and move the shift lever. ∗ : If equipped...
Page 120 2-1. Driving procedures 4-speed models While the engine switch is on, depress the brake pedal and move the shift lever. Shift position uses ■ Function Shift position 5-speed models 4-speed models Parking the vehicle or starting the engine Reversing Neutral Normal driving Position for engine brak- —...
Page 121 2-1. Driving procedures Downshifting restrictions ■ The shift lever cannot be downshifted if the following speeds are exceeded. 2WD models mph (km/h) Maximum speed Downshifting 5-speed models 4-speed models 4 → 3 81 (130) — 3 → 2 56 (90) 71 (115) 2 →...
Page 122 2-1. Driving procedures When driving with the cruise control system (if equipped) ■ The engine brake will not operate when downshifting from D to 4 (5-speed models) or 3 (4-speed models). (→P. 172) If the shift lever cannot be shifted from P ■...
Page 123 2-1. Driving procedures ∗ Manual transmission Shifting the shift lever ■ 6-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly. 5-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly.
Page 124 2-1. Driving procedures Maximum allowable speed ■ Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. 2WD models except PreRunner mph (km/h) Maximum speed Shift position 6-speed models 5-speed models 32 (52) 33 (53) 61 (99) 63 (101) 91 (146)
Page 125 2-1. Driving procedures 4WD models mph (km/h) Maximum speed Shift position Transfer position 6-speed models 5-speed models H2 and H4 30 (49) 30 (48) 11 (19) 11 (18) H2 and H4 58 (93) 57 (92) 22 (36) 22 (36) H2 and H4 85 (137) 82 (133) 33 (53)
Page 126 2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 127 2-1. Driving procedures Parking brake Lever type ● Sets the parking brake Fully set the parking brake U.S.A. Canada while depressing the brake pedal. At this time, the indicator will come on. ● Release the parking brake Press the button Turn the lever clockwise Press it in completely Pedal type...
Page 128 2-1. Driving procedures Parking brake engaged warning buzzer ■ The buzzer sounds to indicate that parking brake is still engaged (with the vehicle having reach a speed of 3 mph [5 km/h]). Usage in winter time ■ See “Winter driving tips” for parking brake usage in winter time. (→P. 217) NOTICE Before driving ■...
Page 129 2-1. Driving procedures Horn To sound the horn, press on or close to the mark. After adjusting the steering wheel ■ Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P.
Page 130 2-2. Gauges and meters Gauges and meters The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Engine coolant temperature gauge Displays the engine coolant temperature.
Page 131 2-2. Gauges and meters Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently.
Page 132 2-2. Gauges and meters NOTICE To prevent damage to the engine and its components ■ Do not let the indicator needle of the tachometer enter the red zone, which ● indicates the maximum engine speed. The engine may be overheating if the engine coolant temperature gauge is ●...
Page 133 2-2. Gauges and meters Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster Center panel...
Page 134 2-2. Gauges and meters Indicators ■ The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Slip indicator (→P. 151) (→P. 188, 190, 199) Headlight high beam VSC OFF indicator indicator (→P. 163) (→P.
Page 135 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
Page 136 Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 137 2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually. Turning the end of the lever turns on the lights as follows: Type A The daytime running lights turn on. side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn The headlights and...
Page 138 2-3. Operating the lights and wipers Type B The daytime running lights turn on. side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn The headlights and Canada all lights listed above (except daytime run- ning lights) turn on.
Page 139 2-3. Operating the lights and wipers Daytime running light system ■ To make your vehicle more visible to other drivers, the front turn signal ● lights turn on automatically whenever the engine is started and the park- ing brake is released. Daytime running lights are not designed for use at night.
Page 140 2-3. Operating the lights and wipers ∗ Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. On/off The fog lights can be turned on only when ■ The headlights are on low beam. ∗...
Page 141 2-3. Operating the lights and wipers Windshield wipers and washer Without intermittent type ■ Type A speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation Washer operation...
Page 142 2-3. Operating the lights and wipers Type B speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation Washer operation...
Page 143 2-3. Operating the lights and wipers Intermittent wiper with interval adjuster ■ Wiper intervals can be adjusted for intermittent operation (when is selected). Type A Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation...
Page 144 2-3. Operating the lights and wipers Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. Type B Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation...
Page 145 2-3. Operating the lights and wipers Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency STY23AF020 Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. The windshield wiper and washer can be operated when ■...
Page 146 2-3. Operating the lights and wipers NOTICE When the windshield is dry ■ Do not use the wipers, as they may damage the windshield. When there is no washer fluid spray from the nozzle ■ Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.
Page 147 2-4. Using other driving systems ∗ Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicator Cruise control switch Setting the vehicle speed ■ Press the ON-OFF button to activate the cruise control. Cruise control indicator will come on.
Page 148 2-4. Using other driving systems Adjusting the set speed ■ To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction.
Page 149 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.
Page 150 2-4. Using other driving systems CAUTION To avoid operating the cruise control by mistake ■ Switch the cruise control off using the ON-OFF button when not in use. Situations unsuitable for cruise control ■ Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
Page 151 2-4. Using other driving systems Rear view monitor system (vehicles with auto anti-glare inside rear view mirror) The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen.
Page 152 2-4. Using other driving systems The rear view monitor system can be operated when ■ The shift lever is in R and engine switch is ON. Switching the screen on/off mode ■ The rear view monitor display on the inside rear view mirror can be turned on/off.
Page 153 2-4. Using other driving systems Displayed area ■ The area covered by the camera is lim- ited. Objects that are close to either corner of the bumper or under the bumper cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.
Page 154 2-4. Using other driving systems Driving precautions ■ When the grade behind the vehicle slopes up sharply, objects appear to be farther away than they actually are. When the grade behind the vehicle slopes down sharply, objects appear to be closer than they actually are.
Page 155 2-4. Using other driving systems The distance that appears on the screen Approx. 1.5 ft. (0.5 m) between three-dimensional objects (such as vehicles) and flat surfaces (such as the road) and the actual distance differ as follows. In reality, C = A < B (C and A are equally far away;...
Page 156 2-4. Using other driving systems Rear view monitor system camera ■ The rear view monitor system camera is located on the tailgate as shown in the illustration. In the following cases, it may become dif- ficult to see the images on the screen, even when the system is functioning cor- rectly.
Page 157 ■ If the back of the vehicle has been hit, the camera’s position and mounting ● angle may have changed. Have the vehicle inspected by your Toyota dealer. Rapid temperature changes, such as when hot water is poured on the ●...
Page 158 2-4. Using other driving systems NOTICE Handling of the camera ■ As the camera has a water proof construction, do not detach, disassemble ● or modify it. This may cause incorrect operation. If the camera lens becomes dirty, it cannot transmit a clear image. If water ●...
Page 159 2-4. Using other driving systems ∗ Four-wheel drive system Use the front-wheel drive control switch to select the following transfer modes. H2 (high speed position, two-wheel drive) Use this for normal driving on dry hard-surfaced roads. This position gives greater economy, quietest ride and least wear.
Page 160 2-4. Using other driving systems Shifting between H4 and L4 Shifting from H4 to L4 ■ Automatic transmission Stop the vehicle completely with brake pedal help down. Shift the shift lever to N. Push and turn the front-wheel drive control switch fully clock- wise.
Page 161 If the indicator light continues to blink even if doing so, contact your Toyota dealer as soon as possible. There may be a trouble in the four-wheel drive...
Page 162 2-4. Using other driving systems Shifting to L4 ■ VSC is automatically turned off. Four-wheel drive usage frequency ■ You should drive in four-wheel drive for at least 10 miles (16 km) each month. This will assure that the front-drive components are lubricated. CAUTION Caution while driving ■...
Page 163 2-4. Using other driving systems ∗ Active traction control system The active traction control system automatically helps prevent the spinning of 4 wheels when the vehicle is started or accelerated on slippery road surfaces. System operation ■ Vehicles with an automatic transmission: Stop the vehicle, shift the shift lever to N and put the front- wheel drive control switch in the L4 position.
Page 164 2-4. Using other driving systems When the rear differential is locked (vehicles with the rear differential ■ lock system) The active traction control system is activated only when the vehicle speed is less than 3 mph (6 km/h). Sounds and vibrations caused by the active traction control system ■...
Page 165 2-4. Using other driving systems AUTO LSD system The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when one of the rear wheels spin- ning occurs in a ditch or rough surface.
Page 166 2-4. Using other driving systems If the engine is turned off and restarted ■ The AUTO LSD system and the indicators are automatically turned off. Reactivation of the VSC system linked to vehicle speed ■ When the AUTO LSD system is turned on, the VSC system will turn on auto- matically if vehicle speed increases.
Page 167 2-4. Using other driving systems ∗ Rear differential lock system The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a slippery or rugged surface. The rear differential lock system is effective in case one of the rear wheels is spinning.
Page 168 2-4. Using other driving systems Manual transmission 4WD models: Before using the rear differential lock system. Stop the vehicle or reduce your speed to less than 2 mph (3 km/h). Depress the clutch pedal and put the front-wheel drive control switch in the L4 position to see if this is sufficient. If this has no effect, additionally use the rear differential lock system.
Page 169 2-4. Using other driving systems After unlocking the rear differential ■ To check that the indicator goes off, turn the engine switch to the ON posi- tion, but do not start the engine. CAUTION To avoid an accident ■ Do not use the rear differential lock system except when wheel spinning ●...
Page 170 2-4. Using other driving systems ∗ Downhill Assist Control system The downhill assist control system helps to prevent excessive speed on steep downhill descents. System operation ■ The system will operate when the vehicle is traveling under 15 mph (25 km/h) and the front-wheel drive control switch is in the L4 position.
Page 171 The downhill assist control system indicator does not come on when the ● DAC switch is pressed. In the above cases have your vehicle checked by your Toyota dealer. CAUTION Do not rely excessively on the downhill assist control system ■...
Page 172 2-4. Using other driving systems ∗ Clutch start cancel switch The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged. Never use the switch for normal engine starting. Be sure to follow the starting procedure.
Page 173 2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ABS (Anti-lock Brake System) ■...
Page 174 2-4. Using other driving systems When the VSC/Trailer Sway Control/TRAC/hill-start assist control systems are operating If the vehicle is in danger of slip- ping or rolling backward when starting on an incline, or if any of the drive wheels spins, the slip indicator light flashes to indicate that the VSC/Trailer Sway Con- trol/TRAC/hill-start assist control...
Page 175 2-4. Using other driving systems To disable VSC, Trailer Sway Control and TRAC (2WD models and 2WD mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer Sway Control and TRAC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it.
Page 176 2-4. Using other driving systems To disable VSC, Trailer Sway Control and/or TRAC (4WD mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer Sway Control and TRAC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it.
Page 177 When the TRAC OFF indicator light comes on even if the VSC OFF ■ switch has not been pressed TRAC, hill-start assist control, downhill assist control system cannot be oper- ated. Contact your Toyota dealer. Reactivation of the TRAC, VSC and Trailer Sway Control systems after ■ turning off the engine Turning off the engine after turning off the TRAC, VSC and Trailer Sway Control systems will automatically reactivate them.
Page 178 2-4. Using other driving systems Hill-start assist control will not operate when (if equipped) ■ The shift lever is in the P, R or N positions. ● The rear differential is locked. ● If the brake system overheats ■ TRAC and hill-start control will cease operation and a buzzer will sound to alert the driver.
Page 179 The ABS, VSC, TRAC and Trailer Sway Control will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. Handling of tires and suspension ■...
Page 180 2-5. Driving information Off-road precautions (4WD models and PreRunner) This vehicle has higher ground clearance and narrower tread in rela- tion to the height of its center of gravity to make it capable of per- forming in a wide variety of off-road applications. Off-road vehicle feature ●...
Page 181 2-5. Driving information CAUTION Off-road vehicle precautions ■ Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: In a rollover crash, an unbelted person is significantly more likely to die ●...
Page 182 2-5. Driving information Off-road driving When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit- ted to travel.
Page 183 2-5. Driving information CAUTION Off-road driving precautions ■ Always observe the following precautions to minimize the risk of serious injury or damage to your vehicle: Drive carefully when off the road. Do not take unnecessary risks by driving ● in dangerous places. Do not grip the steering wheel spokes when driving off-road.
Page 184 2-5. Driving information NOTICE To prevent the water damage ■ Take all necessary safety measures to ensure that water damage to the ● engine or other components does not occur. Water entering the engine air intake will cause severe engine damage. ●...
Page 185 ● For better fuel economy, do not carry unnecessary weight. Deck rails ■ Headboard rail Side rails To use the deck rails, you must install genuine Toyota accessories or their equiva- lent for the deck rails. Follow manufacturer’s instructions and precautions...
Page 186 2-5. Driving information CAUTION When you secure cargo with the deck rails ■ Spread out tie-down/support locations evenly along the length of the ● rails. Do not exceed a total tensile load of 440 lb. (200 kg) per deck rail. ●...
Page 187 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Calculation formula for your vehicle Cargo capacity Total load capacity (vehicle...
Page 188 2-5. Driving information As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.
Page 189 2-5. Driving information CAUTION Storage precautions ■ Never allow anyone to ride in the rear deck. It is not designed for pas- ● sengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or seri- ous bodily injury, in the event of sudden braking, sudden swerving or an accident.
Page 190 2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity. Total load capacity (vehicle capacity weight): (→P. 447) ■ Total load capacity means the combined weight of occupants, cargo and luggage.
Page 191 2-5. Driving information CAUTION Overloading the vehicle ■ Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
Page 192 2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. Pre-winter preparations ■ ● Use fluids that are appropriate to the prevailing outside tem- peratures.
Page 193 2-5. Driving information When driving the vehicle ■ Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. When parking the vehicle ■ Park the vehicle and move the shift lever to P (automatic trans- mission) or 1 or R (manual transmission) without setting the parking brake.
Page 194 2-5. Driving information Snow chain installation ■ Observe the following precautions when installing and removing chains. Install and remove tire chains in a safe location. ● Install tire chains on the rear tires only. Do not install tire chains on the ●...
Page 195 NOTICE Repairing or replacing snow tires ■ Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 196 To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional...
Page 197 2-5. Driving information Towing related terms GCWR (Gross Combination Weight Rating) ■ The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).
Page 198 2-5. Driving information GAWR (Gross Axle Weight Rating) ■ The maximum allowable gross Front GAWR axle weight. The gross axle weight is the load placed on each axle (front and rear). Rear GAWR TWR (Trailer Weight Rating) ■ The maximum allowable gross (With brakes) trailer weight.
Page 199 2-5. Driving information Unbraked TWR (Unbraked Trailer Weight Rating) ■ The trailer weight rating for tow- (Without brakes) ing a trailer without a trailer ser- vice brake system. Tongue Weight ■ The load placed on the trailer hitch ball. (→P. 230)
Page 200 2-5. Driving information Weight limits ● The gross trailer weight must never exceed the TWR described in the table. (→P. 226, 449) ● The gross combination weight must never exceed the GCWR described in the table. (→P. 226) Regular Cab models and Double Cab models ●...
Page 201 2-5. Driving information GCWR, TWR, Unbraked TWR, Fifth wheel and Gooseneck towing TWR Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. GCWR and TWR ■ Regular Cab models Driving Model code...
Page 202 2-5. Driving information Access Cab models Driving Model code Engine GCWR system TRN225L- 7440 lb. CRMDKA (3370 kg) TRN225L- 7470 lb. (3385 kg) CRPDKA 2.7 L TRN245L- 4-cylinder 7850 lb. 3500 lb. CRMDKA (2TR-FE) (3560 kg) (1585 kg) engine TRN245L- 7870 lb.
Page 203 2-5. Driving information Double Cab models Driving Model code Engine GCWR system TRN225L- 7450 lb. 3400 lb. 2.7 L PRPDKA (3375 kg) (1540 kg) 4-cylinder (2TR-FE) TRN265L- 7710 lb. 3500 lb. engine PRPDKA (3495 kg) (1585 kg) 8040 lb. 3500 lb. (3645 kg) (1585 kg) GRN245L-...
Page 204 : With towing package Unbraked TWR ■ 1000 lb. (450 kg) Fifth wheel and gooseneck towing TWR ■ Toyota does not recommend fifth wheel and gooseneck towing. : These models meet the tow-vehicle trailering requirement of SAE International per SAE J2807.
Page 205 2-5. Driving information Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the types of trailers or towing as described below. ● To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. •...
Page 206 Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require- ment of your vehicle.
Page 207 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers stamped with the required trailer ball size.
Page 208 2-5. Driving information Positions for towing hitch receiver and hitch ball Weight carrying ball position: 56.1 in. (1425 mm) Hitch receiver pin hole posi- tion: 44.2 in. (1123 mm) Connecting trailer lights Vehicles with 7 pin connector Use the wire harness stored in the rear end under the vehicle body.
Page 209 ● Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. ● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest.
Page 210 2-5. Driving information ● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right.
Page 211 2-5. Driving information ● Instability happens more frequently when descending steep or long downhill grades. Before descending, slow down and downshift. Do not make sudden downshifts while descending steep or long down- hill grades. ● Avoid holding the brake pedal down too long or applying the brakes too frequently.
Page 212 2-5. Driving information Release the parking brake (and also the brake pedal on vehi- cles with an automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks. Matching trailer ball height to trailer coupler height ■...
Page 213 ■ If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km).
Page 214 2-5. Driving information After the trailer swaying has stopped: ● • Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer. Make sure the load has not shifted.
Page 215 2-5. Driving information CAUTION To avoid accident or injury ■ Do not exceed 65 mph (104 km/h), the posted towing speed limit or the ● speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Slow down sufficiently before making a turn, in cross winds, on wet or slippery surface, etc.
Page 216 NOTICE When installing a trailer hitch ■ Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. Do not directly splice trailer lights ■...
Page 217 2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE To avoid serious damage to your vehicle ■ Do not tow your vehicle with four wheels on the ground.
Page 218 3-1. Using the air conditioning system and defogger Air conditioning system Temperature control dial Fan speed control dial Air outlet selection dial Outside air or recirculated Air conditioning air mode switch ON/OFF switch Adjusting the settings Adjusting the temperature setting ■...
Page 219 3-1. Using the air conditioning system and defogger Selecting the air outlets ■ Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also be selected for more detailed adjustment. When the dial is set to , air flows to the upper body.
Page 220 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the feet and the wind- shield defogger operates. The air intake selector is automat- ically set to outside air mode. To return the recirculated air mode, press Double Cab models only When the dial is set to...
Page 221 3-1. Using the air conditioning system and defogger If the ambient temperature drops while using the recirculated ■ air mode The air intake mode automatically changes from recirculated air mode to outside air mode after a few minutes. To cancel this function: Press and hold for longer than 2 seconds.
Page 222 3-1. Using the air conditioning system and defogger Right and left side outlets Direct air flow to the left or right, up or down. Opening and closing the air outlets Center outlets Open the vent. Close the vent.
Page 223 3-1. Using the air conditioning system and defogger Right and left side outlets Open the vent. Close the vent. For quick clearing of the windshield and side windows ■ Press to turn the air conditioning on. Using the system in recirculated air mode ■...
Page 224 3-1. Using the air conditioning system and defogger CAUTION To prevent the windshield from fogging up ■ Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.
Page 225 3-2. Using the audio system Audio system types Refer to the “Display Audio System Owner’s Manual”. Type A Type B...
Page 226 3-2. Using the audio system Steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. For details, refer to the “Display Audio System Owner’s Manual”. Operation may differ and usage may not be possible with audio sys- tem that are not compatible with the steering switches in this vehicle.
Page 227 3-2. Using the audio system CAUTION For vehicles sold in U.S.A. and Canada ■ Properly shielded a grounded cables and connectors must be used for con- nection to host computer and/or peripherals in order to meet FCC emission limits. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Page 228 3-2. Using the audio system Operating the sub woofer (on some Access Cab models) LIGHT ON The sub woofer illumination turns on. In this position, the sub woofer operates.
Page 229 3-2. Using the audio system Using the AUX port/USB port This adapter can be used to connect a portable audio device and lis- ten to it through the vehicle’s speakers. Open the cover and connect the portable audio device. Operating portable audio devices connected to the audio system ■...
Page 230 3-2. Using the audio system Detachable pole antenna The antenna can be removed. Removing the antenna ■ Place the included wrench around the antenna. When not in use, the wrench is stored in glove box. Loosen the antenna with the wrench and remove it.
Page 231 3-2. Using the audio system Installing the antenna ■ Tighten the antenna by one hand until it will not turn any more. Using the wrench, tighten the antenna an additional 1/8th turn (20 to 45 degrees) to secure it in place. After tightening the antenna, remove the wrench.
Page 232 3-2. Using the audio system NOTICE To avoid damaging the antenna ■ Remove the antenna in the following situations. When using an automatic carwash. ● When the antenna will touch the ceiling of a garage, etc. ● When covering the vehicle with a car cover. ●...
Page 233 3-3. Using the interior lights Interior lights list Interior light (→P. 260) Personal lights (Access Cab and Double Cab models) (→P. 260) Illuminated entry system ■ When the interior light switch is in the DOOR position, the interior light auto- matically turns on/off according to whether the doors are locked/unlocked and whether the doors are open/closed.
Page 234: Interior Light
3-3. Using the interior lights Interior light and personal lights Interior light DOOR position Personal lights (Access Cab and Double Cab models) On/off...
Page 235 3-4. Using the storage features List of storage features Glove box Overhead console (Access Cab and Double Cab models) Bottle holders Auxiliary boxes Front console box (separated type front seat only) Cup holders CAUTION Items that should not be left in the storage spaces ■...
Page 236: Glove Box
3-4. Using the storage features Glove box and front console box Glove box Pull up the lever. CAUTION Caution while driving ■ Keep the glove box closed. In the event of sudden braking or sudden swerv- ing, an accident may occur due to an occupant being struck by the open glove box or the items stored inside.
Page 237 3-4. Using the storage features Cup holders Cup holders Type A (Bench type front seat) Type B (Separated type front seats with an automatic transmis- sion) Type C (Separated type front seats with a manual transmission)
Page 238 3-4. Using the storage features Cup holders Removing the cup holder ■ Type A (Bench type front seat) Pull the cup holder up. Type B (Separated type front seats with an automatic transmission) Pull the cup holder up. CAUTION Items unsuitable for the cup holder ■...
Page 239: Bottle Holders
3-4. Using the storage features Bottle holders Bottle holders Front Front console box (Separated type front seat) Rear (Double Cab models) Bottle holders ■ Depending on their size or shape, some bottles may not fit in the holders.
Page 240: Auxiliary Boxes
3-4. Using the storage features Bottle holders and auxiliary boxes NOTICE Items that should not be stowed in the bottle holders ■ Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.
Page 241 3-4. Using the storage features Auxiliary boxes Turn the knob counterclockwise. Open the lid. Press the lid against the bot- tom of the lower cushion until it is supported by the hook- and-loop fastener. Make sure that the lid is sup- ported to prevent it from closing unexpectedly.
Page 242 3-4. Using the storage features Auxiliary boxes and overhead console CAUTION Caution while driving ■ Keep the auxiliary boxes closed and locked. Injuries may result in the event of an accident or sudden braking. Overhead console (Access Cab and Double Cab models) The overhead console is useful for temporarily storing sunglasses and similar small items.
Page 243 3-5. Other interior features Sun visors Type A Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. Type B Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. Side extender: Place in side position, then slide backwards.
Page 244 3-5. Other interior features Vanity mirrors Vehicles without vanity light Vehicles with vanity light Slide the cover. The light turns on when the cover is opened.
Page 245 3-5. Other interior features Clock Adjusts the hours Adjusts the minutes The clock is displayed when ■ The engine switch is in the ACC or ON position. When disconnecting and reconnecting battery terminals ■ The time display will automatically be set to 1:00.
Page 246 3-5. Other interior features Outside temperature display (vehicles with auto anti-glare inside rear view mirror) The temperature display shows temperatures within the ranges of -40°F (-40°C) and 122°F (50°C). Outside temperature display ■ Type A Type B Ice advisory indicator ■...
Page 247 3-5. Other interior features Changing the display The outside temperature display on the inside rear view mirror can be turned on/off and the display units can be changed. Turning the outside temperature display on/off ■ Type A: Press and hold to display “Custom Settings Menu”.
Page 248 3-5. Other interior features Changing display units ■ Type A: Press and hold to display “Custom Settings Menu”. Type B: Press to display “Custom Settings Menu”. Type A: Press and select “Outside Temperature”, then press and hold Type B: Press and select “Outside Temperature”, then press...
Page 249 3-5. Other interior features Setting the ice advisory indicator The ice advisory indicator on the inside rear view mirror can be turned on/off. Type A: Press and hold to display “Custom Settings Menu”. Type B: Press to display “Custom Settings Menu”. Type A: Press and select “Ice Advisory”.
Page 250 When “– –” or “– – –” is displayed ■ The system may be malfunctioning. Take your vehicle to your Toyota dealer. Customization that can be configured for the inside rear view mirror ■ display Settings (e.g.
Page 251 3-5. Other interior features Power outlets (12V DC) The power outlets can be used for 12V accessories that run on less than 10A. The power outlets can be used when ■ The engine switch is in the ACC or ON position. NOTICE To avoid damaging the power outlets ■...
Page 252 3-5. Other interior features ∗ Power outlet (120V AC) The power outlet can be used for electrical appliances. Main switch To use the power outlet, turn on the main switch. The power supply starts a few seconds after the main switch is pressed.
Page 253 3-5. Other interior features • The shift lever is in N and the clutch pedal is not depressed. (manual transmission) A maximum capacity of 400W can only be restored by turning the power outlet main switch off and then on again under condi- tion described above.
Page 254 When the cabin temperature is high, open the windows to cool the tempera- ture down. Once it reaches the normal temperature, turn the power outlet main switch on again. If the power supply is not resumed even after performing the above proce- dure, have the vehicle inspected by a Toyota dealer.
Page 255 Do not modify, disassemble or repair the power outlet or its inverter, in any ● way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs. To prevent injuries and accidents, securely fix all electric appliances ■...
Page 256 3-5. Other interior features NOTICE To avoid damaging the power outlet and the plug ■ Close the power outlet lid when not in use. ● Foreign objects or liquids that enter the power outlet may cause a short ● circuit. Do not use plug adaptors to connect too many plugs to the power outlet.
Page 257 If the power outlet is loose when an electrical appliance plug is con- ■ nected Replace the outlet. Contact a Toyota dealer for any necessary replacements. If the power outlet gets dirty ■ Turn the main switch off and use a soft, clean cloth to wipe it gently.
Page 258 3-5. Other interior features ∗ Seat heaters The indicator comes on. Adjusts the seat tempera- ture. The further you turn the dial upward, the warmer the seat becomes. The seat heaters can be used when ■ The engine switch is in the ON position. When not in use ■...
Page 259 3-5. Other interior features CAUTION Burns ■ Use caution when seating the following persons in a seat with the seat ● heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically chal- lenged •...
Page 260 3-5. Other interior features ∗ Seatback table Front passenger’s seatback can be used as a temporary table only when the vehicle is stopped. Fold down the front passen- ger’s seat to use the seatback table. (→P. 49) CAUTION Caution while driving ■...
Page 261 3-5. Other interior features Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eye- lets.
Page 262 ■ Do not use floor mats designed for other models or different model year ● vehicles, even if they are Toyota Genuine floor mats. Only use floor mats designed for the driver’s seat. ● Always install the floor mat securely using the retaining hooks (clips) pro- ●...
Page 263 3-5. Other interior features Luggage compartment features Behind the rear seat (Double Cab models only) Cargo net hooks (vehicles with sub woofer) Grocery bag hooks Flashlight holder Storage boxes Deck Auxiliary boxes Tie-down cleats Deck hooks...
Page 264 3-5. Other interior features Auxiliary boxes Left side Turn the knob counterclock- wise. Open the lid. Right side (vehicles without 120V power outlet) Turn the knob counterclock- wise. Open the lid. Right side (vehicles with 120V power outlet) Turn the knob counterclock- wise.
Page 265 3-5. Other interior features CAUTION Caution while driving ■ Keep the auxiliary boxes closed and locked. Injuries may result in the event of an accident or sudden braking. Deck hooks Deck hooks are provided for securing loose items. CAUTION When not in use ■...
Page 266 3-5. Other interior features Tie-down cleats The deck rail system enables you to insert and move tie-down cleats to their best location along deck rails to secure a load. Locking plate Thumb wheel Tie-down cleat Installing the tie-down cleat ■ Loosen the thumb wheel in a counterclockwise motion, and depress the wheel so that the...
Page 267 3-5. Other interior features Insert the locking plate into the deck rail, rotate the tie-down cleat 90°, and release the thumb wheel. Slide the cleat to the closest detent in the rail system. You will feel that the locking plate snaps into a detent.
Page 268 3-5. Other interior features CAUTION Tie-down cleat precautions ■ Properly install and tighten the tie-down cleats into the deck rail system. ● Failure to properly install and tighten the tie-down cleats can cause cargo to become unsecured. Unsecured cargo can cause injury when the vehi- cle is in motion.
Page 269 3-5. Other interior features Left side Removing the separator ■ Remove the separator. It can be installed in various positions as required. Flashlight holder (Double Cab models only) Flashlight holder is designed to hold the flashlight securely.
Page 270 3-5. Other interior features Removing the flashlight holder ■ Remove the flashlight holder. It can be installed in various positions as required. Grocery bag hooks (Double Cab models only) Grocery bag hook is designed to hang things like grocery bag. NOTICE Grocery bag hook weight capacity ■...
Page 271 3-5. Other interior features Cargo net hooks (Double Cab models with sub woofer) Cargo net hooks are designed to hang the factory-supplied cargo net. NOTICE To prevent damage to the cargo net hook ■ Do not hang items other than the cargo net.
Page 272 3-5. Other interior features ∗ Garage door opener The garage door opener can be trained to operate garage doors, gates, entry doors, door locks, home lighting systems, security sys- tems, and other devices. The training procedure is displayed on the inside rear view mirror display screen.
Page 273 3-5. Other interior features ® Training the HomeLink ■ Point the remote control trans- mitter for the device 1 to 3 in. (25 ® to 75 mm) from the HomeLink control buttons. Keep indicator ® HomeLink in view while training. Press and hold down one of the ®...
Page 274 3-5. Other interior features Test operation ® HomeLink pressing newly trained button. If training a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the Rolling Code type.
Page 275 3-5. Other interior features Training a Rolling Code system (for U.S. owners) ■ If your device is Rolling Code equipped, follow the steps under the ® heading “Training the HomeLink ” before proceeding with the steps listed below. Locate the learn button on the ceiling mounted garage door opener motor.
Page 276 HomeLink buttons. Training other devices ■ To train other devices such as home security systems, home door locks and lighting, contact your Toyota dealer for assistance. Retraining a button ■ ® The individual HomeLink buttons cannot be erased but can be ®...
Page 277 3-5. Other interior features ® Operating HomeLink ® ® Press the appropriate HomeLink button. The HomeLink indicator light should come on. ® The HomeLink compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed. ®...
Page 278 3-5. Other interior features Before training ■ Install a new battery in the remote control transmitter. ● The battery side of the remote control transmitter must be pointed away ● ® from the HomeLink button. Certification for the garage door opener ■...
Page 279 3-5. Other interior features If the following message is displayed ■ This message appears when training procedures have not been performed correctly. Follow the instructions on the screen to complete or cancel train- ing. Pattern A Pattern B When support is necessary ■...
Page 280 3-5. Other interior features CAUTION When training a garage door or other remote control devices ■ The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm. Conforming to federal safety standards ■...
Page 281 3-5. Other interior features Compass (vehicles with auto anti-glare inside rear view mirror) The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. Location ■ Type A Type B...
Page 282 3-5. Other interior features Displays and directions ■ Display Direction North Northeast East Southeast South Southwest West Northwest...
Page 283 3-5. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies depending on the geographic position of the vehicle. If you cross over one of the map boundaries shown in the illustration, the compass will deviate.
Page 284 3-5. Other interior features Type A: Press and select “Compass”, then press and hold Type B: Press and select “Compass”, then press Type A: Press and select “Compass Display”. Type B: Press and select “Compass Display”. Type A: Press and hold and select display on/off.
Page 285 3-5. Other interior features Type A: Press and select “Zone”, then press and hold Type B: Press and select “Zone”, then press Type A: The selected country changes each time is pressed. Select the country, then press and hold confirm. Type B: The selected country changes each...
Page 286 3-5. Other interior features Circling calibration If “C” appears on the display, circling calibration needs to be per- formed. Stop the vehicle in a place where it is safe to drive in a circle. Type A: Press and hold to display “Custom Settings Menu”.
Page 287 3-5. Other interior features Drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed. If there is not enough space to drive in a circle, drive around the block until a direction is dis- played.
Page 288 3-5. Other interior features CAUTION While driving the vehicle ■ Do not adjust the display. Adjust the display only when the vehicle is stopped. When doing the circling calibration ■ Secure a wide space, and watch out for people and vehicles in the vicinity. Do not violate any local traffic rules while performing circling calibration.
Page 289 4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 290 4-1. Maintenance and care Aluminum or chrome cladded wheels (if equipped) ■ Remove any dirt immediately by using a neutral detergent. Do not use ● hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint. Do not use detergent on the wheels when they are hot, for example after ●...
Page 291 4-1. Maintenance and care NOTICE Clean the drainage hole of the deck ● regularly. If the drainage hole is stopped up, the water will not be able to flow, and it will cause rust. Cleaning the exterior lights ■ Wash carefully. Do not use organic substances or scrub with a hard brush. ●...
Page 292 ● Allow the solution to soak in for a few minutes. Remove the dirt and wipe off the solution with a clean, damp cloth. Caring for leather areas ■ Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.
Page 293 4-1. Maintenance and care Shampooing the carpets ■ There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. The excellent results are obtained when keeping the carpet as dry as possible.
Page 294 4-1. Maintenance and care NOTICE Cleaning detergents ■ Do not use organic substances such as benzene or gasoline, acidic or ● alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. Do not use polish wax or polish cleaner.
Page 295: Scheduled Maintenance
Repair and replacement ■ It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than Toyota dealer performs repairs, confirm the war-...
Page 296 ON position. Continue to press and hold the button until the odometer displays 000000. If the system fails to reset, the light will continue flashing. Allow inspection and repairs to be performed by a Toyota dealer ■ Toyota technicians are well-trained specialists and are kept up to date ●...
Page 297: Engine Compartment
“Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items...
Page 298: Vehicle Interior
4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be held securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 299: Vehicle Exterior
4-2. Maintenance Items Check points • Moves smoothly? Steering wheel • Has correct free play? • No strange noises? Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? •...
Page 300 The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. Your vehicle may not pass the I/M test: ■...
Page 301 • FMVSS No.116 DOT 3 or SAE Brake fluid level (→P. 342) J1703 brake fluid • Rag or paper towel • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 302 4-3. Do-it-yourself maintenance Items Parts and tools • Bulb with same number and watt- age rating as original Light bulbs (→P. 382) • Phillips-head screwdriver • Conventional wrench • Automatic transmission fluid Power steering fluid level ® DEXRON II or III (→P.
Page 303 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. When working on the engine compartment ■ Keep hands, clothing, and tools away from the moving fan and engine ●...
Page 304 4-3. Do-it-yourself maintenance NOTICE If you remove the air cleaner ■ Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. If the fluid level is low or high ■ It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high.
Page 305 4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. The hood will pop up slightly. Pull up the hood catch lever and lift the hood.
Page 306 4-3. Do-it-yourself maintenance Hold the hood open by insert- ing the supporting rod into the slot. CAUTION Pre-driving check ■ Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
Page 307 4-3. Do-it-yourself maintenance Engine compartment 2.7 L 4-cylinder (2TR-FE) engine Washer fluid tank (→P. 348) Engine oil level dipstick (→P. 336) Radiator cap Brake fluid reservoir Engine coolant reservoir (→P. 342) (→P. 340) Fuse box (→P. 372) Engine oil filler cap (→P.
Page 308 4-3. Do-it-yourself maintenance 4.0 L V6 (1GR-FE) engine Washer fluid tank (→P. 348) Engine oil filler cap (→P. 337) Power steering fluid reservoir (→P. 344) Brake fluid reservoir (→P. 342) Radiator cap Fuse box (→P. 372) Engine oil level dipstick (→P.
Page 309 4-3. Do-it-yourself maintenance Engine oil Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. Checking the engine oil ■ Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
Page 310 4-3. Do-it-yourself maintenance 2.7 L 4-cylinder (2TR-FE) engine Full 4.0 L V6 (1GR-FE) engine Full Adding engine oil ■ 2.7 L 4-cylinder (2TR-FE) engine If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
Page 311 4-3. Do-it-yourself maintenance 4.0 L V6 (1GR-FE) engine Make sure to check the oil type and prepare the items needed before adding oil. →P. 454 Engine oil selection Items Clean funnel Remove the oil filler cap, turning it counterclockwise. Add engine oil slowly. Checking the dipstick.
Page 312 ● not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal. Do not leave used engine oil within the reach of children.
Page 313: Engine Coolant
4-3. Do-it-yourself maintenance NOTICE To prevent serious engine damage ■ Check the oil level on regular basis. When replacing the engine oil ■ Be careful not to spill engine oil on the vehicle components. ● Avoid overfilling, as the engine could be damaged. ●...
Page 314 ■ Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system. Coolant selection ■...
Page 315 Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION When the engine is hot ■...
Page 316 4-3. Do-it-yourself maintenance Adding fluid ■ Make sure to check the fluid type and prepare the necessary items. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Rag or paper towel Type B only Turn the engine off. Depress the brake pedal 20 times or more.
Page 317 4-3. Do-it-yourself maintenance Power steering fluid Fluid level ■ The fluid level should be within the appropriate range. 2.7 L 4-cylinder (2TR-FE) engine Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot) Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures.
Page 318 4-3. Do-it-yourself maintenance Checking the fluid level ■ Make sure to check the fluid type and prepare the necessary items. ® Fluid type Automatic transmission fluid DEXRON II or III Items Rag or paper towel Clean all dirt off the reservoir. Remove the cap by turning it counterclockwise.
Page 319 4-3. Do-it-yourself maintenance Battery Battery exterior ■ Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps. Terminals Hold-down clamp Before recharging ■ When recharging, the battery produces hydrogen gas which is flammable and explosive.
Page 320 4-3. Do-it-yourself maintenance CAUTION Chemicals in the battery ■ A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near bat- tery: Do not cause sparks by touching the battery terminals with tools.
Page 321 4-3. Do-it-yourself maintenance NOTICE When recharging the battery ■ Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. Washer fluid If the washer does not work, the washer tank may be empty. Open the lid.
Page 322 4-3. Do-it-yourself maintenance NOTICE Do not use any fluid other than washer fluid ■ Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces. Diluting washer fluid ■ Dilute washer fluid with water as necessary.
Page 323 The tire pressure warning system ■ Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 406)
Page 324 Have tire pressure warning valve and trans- mitter ID codes registered by your Toyota dealer. (→P. 352) Initializing the tire pressure warning system The tire pressure warning system must be initialized in the fol- ■...
Page 325 The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.
Page 326 A tire goes flat repeatedly or cannot be properly repaired due to the ● size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. Replacing tires and wheels ■ If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
Page 327 4-3. Do-it-yourself maintenance Access Cab models Tire types ■ 1 Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 328 If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. When operating the tire pressure warning reset switch, the tire pres- ●...
Page 329 4-3. Do-it-yourself maintenance Tire pressure warning system certification ■ FCC ID: PAXPMV107J PAXPMV108J FCC ID: HYQ13BCX For vehicles sold in U.S.A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 330 Do not mix tires of different makes, models or tread patterns. ● Also, do not mix tires of remarkably different treadwear. Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply ●...
Page 331 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 332 4-3. Do-it-yourself maintenance Tire inflation pressure Tire inflation pressure ■ The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 462) Regular Cab and Double Cab models...
Page 333 4-3. Do-it-yourself maintenance Access Cab models...
Page 334 4-3. Do-it-yourself maintenance Inspection and adjustment procedure ■ Tire valve Tire pressure gauge Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire.
Page 335 Reduced safety ● Damage to the drive train ● If a tire needs frequent refilling, have it checked by your Toyota dealer. Instructions for checking tire inflation pressure ■ When checking tire inflation pressure, observe the following: Check only when the tires are cold.
Page 336 4-3. Do-it-yourself maintenance CAUTION Proper inflation is critical to save tire performance ■ Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. Excessive wear ● Uneven wear ● Poor handling ●...
Page 337 ● Bent wheels that have been straightened Wheel precautions ■ ● Use only Toyota wheel nuts and wrench designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 100 miles (160 km).
Page 338 When replacing wheels ■ The wheels of your Toyota are equipped with tire pressure warning valves and transmitters (except for spare tire) that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure.
Page 339 Because tire repair or replacement may affect the tire pressure warn- ● ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 340 4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method ■ Turn the engine switch to the LOCK position. Open the glove box. Slide off the damper. Push in each side of the glove box to disconnect the claws.
Page 341 4-3. Do-it-yourself maintenance Open the filter door. Remove the filter. Replacement method ■ Remove the air conditioning filter and replace it with a new one. When installing the filter, follow the instructions indicated on the label.
Page 342 4-3. Do-it-yourself maintenance Checking interval ■ Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) If air flow from the vents decreases dramatically ■...
Page 343 4-3. Do-it-yourself maintenance ∗ Wireless remote control battery Replace the battery with a new one if it is discharged. You will need the following items: ■ Lithium battery CR2032 Replacing the battery ■ Remove the cover using a coin protected with tape etc. Remove the discharged trans- mitter battery.
Page 344 ● The operational range is reduced. ● Use a CR2032 lithium battery ■ Batteries can be purchased at your Toyota dealer, jewelers, or camera ● stores. Replace only with the same or equivalent type recommended by your ● Toyota dealer.
Page 345 4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch to the LOCK position. The fuses are located in the following places. To check the fuses, follow the instructions below.
Page 346 4-3. Do-it-yourself maintenance After a system failure, see “Fuse layout and amperage ratings” (→P. 375) for details about which fuse to check. Remove the fuse with the pull- out tool. Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
Page 347 4-3. Do-it-yourself maintenance Type B Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. Type C Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
Page 348 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings Engine compartment ■ Type A Type B...
Page 349 4-3. Do-it-yourself maintenance Fuse Ampere Circuit 10 A Air conditioning system TOWING TAIL 30 A Trailer lights (tail lights) FOG FR 15 A Front fog lights Stop lights, high mounted stop- light, vehicle stability control sys- tem, anti-lock brake system, shift STOP 10 A lock system, multiport fuel injection...
Page 350 4-3. Do-it-yourself maintenance Fuse Ampere Circuit ALT-S 7.5 A Charging system Multiport fuel injection system/ EFI-MAIN 20 A sequential multiport fuel injection system HORN 10 A Horn Multiport fuel injection system/ A/F HTR 15 A sequential multiport fuel injection system Wireless remote control system, air conditioning system, multiplex communication system, meter and...
Page 351 4-3. Do-it-yourself maintenance Fuse Ampere Circuit IGN and GAUGE fuses, multiport 30 A fuel injection system/sequential multiport fuel injection system Multiport fuel injection system/ AIR PMP 50 A sequential multiport fuel injection system Anti-lock brake system, vehicle sta- ABS NO.2 30 A bility control system 100 A...
Page 352 4-3. Do-it-yourself maintenance Under the instrument panel ■ Fuse Ampere Circuit Multiport fuel injection system/ sequential multiport fuel injection system, anti-lock brake system, 15 A traction control system, vehicle sta- bility control system, SRS airbag system, front passenger occupant classification system Meter and gauge, emergency GAUGE 7.5 A...
Page 353 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Anti-lock brake system, vehicle sta- bility control system, stop lights, charging system, multiport fuel injection system/sequential multi- port fuel injection system, air condi- IG1 NO.2 10 A tioning system, instrument panel light control, anti-glare inside rear view mirror, back monitor, clutch start cancel switch, rear differential lock system, power outlets, tire...
Page 354 Never use a fuse of a higher amperage rating than indicated, or use any ● other object in place of a fuse. Always use a genuine Toyota fuse or equivalent. ● Never replace a fuse with a wire, even as a temporary fix.
Page 355 You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 356: Replacing Light Bulbs
4-3. Do-it-yourself maintenance Rear bulb locations ■ High mounted stoplight Rear turn signal lights Stop/tail and rear side Back-up lights marker lights (bulb type only) License plate lights Replacing light bulbs Headlights ■ Unplug the connector.
Page 357 4-3. Do-it-yourself maintenance Remove the rubber cover. Release bulb retaining spring. Remove the bulb. To install a new bulb, align the tabs of the bulb with the cutouts of the mounting hole.
Page 358 4-3. Do-it-yourself maintenance Front fog lights (if equipped) ■ Unplug the connector while pull- ing the lock release. Turn the bulb counterclockwise.
Page 359 4-3. Do-it-yourself maintenance Front side marker lights ■ Turn the bulb base counterclock- wise. Remove the light bulb.
Page 360 4-3. Do-it-yourself maintenance Front turn signal lights/parking lights/daytime running lights ■ Turn the bulb base counterclock- wise. Remove the light bulb.
Page 361 4-3. Do-it-yourself maintenance Stop/tail lights, rear side marker lights (bulb type only), back- ■ up lights and rear turn signal lights Remove the bolts and rear com- bination assembly. Unplug connector while depressing the lock release. Turn the bulb bases counter- clockwise.
Page 362 4-3. Do-it-yourself maintenance High mounted stoplight ■ Remove the screws and cover. Remove the light bulbs.
Page 363 4-3. Do-it-yourself maintenance License plate lights ■ Remove the screw and light unit. Turn the bulb base counterclock- wise. Remove the light bulb.
Page 364 • Rear side marker lights (LED type) Condensation build-up on the inside of the lens ■ Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction.
Page 365 4-3. Do-it-yourself maintenance...
Page 366 5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. NOTICE To prevent battery discharge ■...
Page 367 If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Page 368 5-1. Essential information Type B Towing hook Emergency towing procedure ■ The engine switch must be in the ACC (engine off) or the ON (engine running) position. 4WD models: Put the front-wheel drive control switch in H2. Put the shift lever in N. Release the parking brake.
Page 369 5-1. Essential information NOTICE Emergency towing eyelet/hook precautions ■ Before emergency towing, check that the eyelet/hook is not broken or ● damaged. Fasten the towing cable or chain securely to the eyelet/hook. ● Do not jerk the eyelet/hook. Apply steady and even force. ●...
Page 370 5-1. Essential information Towing with a wheel lift-type truck from the front Vehicles with an automatic trans- mission: Use a towing dolly under the rear wheels. 2WD models with a manual transmission: We recommend to use a towing dolly under the rear wheels.
Page 371 5-1. Essential information Towing with a wheel lift-type truck from the rear 2WD models Turn the engine switch to the ACC position. 4WD models We recommend to use a towing dolly under the front wheels. When not using a towing dolly, turn the engine switch to the ACC position, shift the shift lever to N and put the front-wheel drive con-...
Page 372 5-1. Essential information Using a flat bed truck If your Toyota is transported by a Front flat bed truck, it should be tied down at the locations shown in the illustration. If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°.
Page 373 5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. Visible symptoms ■ ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
Page 374 5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 375 Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Brake system warning light (warning buzzer)* •...
Page 376 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: •...
Page 377 5-2. Steps to take in an emergency Warning light Warning light/Details SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; • The seat belt pretensioner system. ABS warning light (U.S.A.) Indicates a malfunction in: •...
Page 378 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning light Warning light/Details Correction procedure Open door warning light Check that all doors Indicates that a door is are closed.
Page 379 Toyota dealer. • When the light stays on Have the system after blinking for 1 checked by your minute: Malfunction in Toyota dealer.
Page 380 5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Maintenance required reminder light Indicates that mainte- nance is required accord- ing to the driven distance on the maintenance schedule. Illuminates for about 3 seconds and then flashes for about 15 sec- If necessary, perform onds approximately 4500...
Page 381 If it is, tighten it securely. The light will go off after taking several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible. Front passenger detection sensor and passenger seat belt reminder ■...
Page 382 If there is a lot of snow or ice on the vehicle, in particular around the ● wheels or wheel housings. If non-genuine Toyota wheels are used. (Even if you use Toyota ● wheels, the tire pressure warning system may not work properly with some types of tires.)
Page 383 Check the tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota dealer. Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate, ●...
Page 384 5-2. Steps to take in an emergency CAUTION Maintenance of the tire ■ Please note that the TPMS (tire pressure warning system) is not a sub- stitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale (tire pressure warning light).
Page 385 5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. Before jacking up the vehicle ■ ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ●...
Page 386 5-2. Steps to take in an emergency Access Cab models Tool bag Jack Double Cab models Tool bag Jack Taking out the jack and tool bag Regular Cab models with bench type seat Pull the lever and fold down the seatback.
Page 387 5-2. Steps to take in an emergency Regular Cab models with separated type seat Pull the lever and fold down the seatback. Unhook the strap and remove the tool bag. Loosen and remove the jack. Loosen Tighten...
Page 388 5-2. Steps to take in an emergency Access Cab models Pull up the lever. Raise the bottom cushion up. Turn the knob counterclockwise. Open the lid. Press the lid against the bot- tom of the lower cushion until it is supported by the hook- and-loop fastener.
Page 389 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Double Cab models Swing the bottom cushion up by pulling the lock release strap. Turn the knob counterclock- wise. Open the lid. Unhook the strap and remove the tool bag.
Page 390 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Assemble the jack handle (in the tool bag) Assemble the jack handle exten- sion as shown.
Page 391 5-2. Steps to take in an emergency Taking out the spare tire Insert the end of the jack handle extension into lowering screw and turn it counterclock- wise. After the tire is lowered com- pletely to the ground, remove the holding bracket.
Page 392 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Wheel Flat tire chock positions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of Left- the front...
Page 393 5-2. Steps to take in an emergency Slightly loosen the wheel nuts (one turn). Assemble the jack handle exten- sion as shown. Position the jack at the correct jack point as shown. Front Rear Make sure the jack is positioned on a level and solid place.
Page 394 5-2. Steps to take in an emergency Remove all the wheel nuts and the tire. When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface. Installing the tire Remove any dirt or foreign mat- ter from the wheel contact sur- face.
Page 395 5-2. Steps to take in an emergency Replacing an aluminum wheel with a steel wheel Tighten the nuts until the tapered Tapered portion portion comes into loose contact with the disc wheel sheet. Disc wheel sheet Replacing an aluminum wheel with an aluminum wheel Tighten the nuts until the washer Washer of the nut comes into loose con-...
Page 396 5-2. Steps to take in an emergency Firmly tighten each nut two or three times in the order shown in the illustration. Tightening torque: 83 ft·lbf (113 N·m, 11.5 kgf·m) 2WD models except PreRunner 4WD models and PreRunner Stowing the flat tire, jack and all tools Lay down the tire with the outer side facing up, and install the holding bracket.
Page 397 5-2. Steps to take in an emergency 4WD models only: Fasten the claws of the holding bracket into the wheel holes as shown in the illustration. Holding bracket Claw Then secure the tire, taking care that the tire goes straight up without catching on any other part, to prevent it from flying for- ward during a collision or sudden braking.
Page 398 5-2. Steps to take in an emergency CAUTION Using the jack ■ Improper use of the jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. Do not use the jack for any purpose other than replacing tires or install- ●...
Page 399 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • Do not attach a heavily damaged wheel ornament, as it may fly off the wheel while the vehicle is moving.
Page 400 5-2. Steps to take in an emergency CAUTION Speed limit when using the temporary spare tire ■ Do not drive at speeds in excess of 50 mph (80 km/h) when a temporary spare tire is installed on the vehicle. The temporary spare tire is not designed for driving at high speeds. Fail- ing to observe this precaution may lead to an accident causing death or serious injury.
Page 401 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
Page 402 One of the following may be the cause of the problem. ● One or both of the battery terminals may be disconnected. ● The battery may be discharged. (→P. 434) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.
Page 403 (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 404 5-2. Steps to take in an emergency If you lose your keys New genuine Toyota keys can be made by your Toyota dealer using the other key and the key number stamped on your key number plate.
Page 405 You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. Connect the jumper cables.
Page 406 Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.
Page 407 5-2. Steps to take in an emergency Starting the engine when the battery is discharged (vehicles with an ■ automatic transmission) The engine cannot be started by push-starting. Avoiding a discharged battery ■ Turn off the headlights and the audio system while the engine is turned ●...
Page 408 5-2. Steps to take in an emergency CAUTION Battery precautions ■ The battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following pre- cautions when handling the battery. When working with the battery, always wear safety glasses and take care ●...
Page 409 (radiator), hoses, etc. for any leaks. If there is a large quantity of engine coolant leaking, imme- diately contact your Toyota dealer. Inspect the amount of engine coolant by checking if the res- ervoir level is between “FULL”...
Page 410 If the fan does not operate: Stop the engine immediately and contact your Toyota dealer. If the fan operates: Have the vehicle inspected at the nearest Toyota dealer. CAUTION To prevent an accident or injury when inspecting under the hood of ■...
Page 411 5-2. Steps to take in an emergency NOTICE When adding engine coolant ■ Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.
Page 412 5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. Stop the engine. Set the parking brake and put the shift lever in P (vehicles with an automatic transmission) or N (vehicles with a manual transmission).
Page 413 5-2. Steps to take in an emergency NOTICE To avoid damaging the transmission and other components ■ Avoid spinning the wheels and do not rev the engine. ● If the vehicle remains stuck after trying these procedures, the vehicle may ●...
Page 414 5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmly depress it.
Page 415 5-2. Steps to take in an emergency CAUTION If the engine has to be turned off while driving ■ Power assist for the brakes and steering wheel will be lost, making the ● brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 416 5-2. Steps to take in an emergency...
Page 417 6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions 2WD models except PreRunner Access Cab Cab type Regular Cab Double Cab Except X-Runner X-Runner 190.4 in. 208.1 in. 208.5 in. 208.1 in. Overall length (4835 mm) (5285 mm) (5295 mm) (5285 mm) 74.0 in.
Page 418: Vehicle Capacity Weight
2.7 L 4-cylinder Double Cab 950 lb. (430 kg) (2TR-FE) engine : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your Toyota dealer about the weight of accessory parts.
Page 419 (1GR-FE) engine Long deck : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your Toyota dealer about the weight of accessory parts. 4WD models Vehicle capacity Cab type Engine...
Page 420 6-1. Specifications TWR (Trailer Weight Rating) Regular Cab models Driving Model code Engine system TRN220L-TRMDKA TRN220L-TRPDKA 2.7 L 4-cylinder 3500 lb. (1585 kg) (2TR-FE) engine TRN240L-TRMDKA TRN240L-TRPDKA Access Cab models Driving Model code Engine system TRN225L-CRMDKA TRN225L-CRPDKA 2.7 L 4-cylinder TRN245L-CRMDKA 3500 lb.
Page 421 6-1. Specifications Double Cab models Driving Model code Engine system TRN225L-PRPDKA 3400 lb. (1540 kg) 2.7 L 4-cylinder (2TR-FE) engine TRN265L-PRPDKA 3500 lb. (1585 kg) 3500 lb. (1585 kg) GRN245L-PRADKA 6500 lb. (2945 kg) 3500 lb. (1585 kg) GRN245L-PRFDKA 6500 lb. (2945 kg) 3500 lb.
Page 422 Vehicle identification number ■ The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 423 6-1. Specifications Engine number ■ The engine number is stamped on the engine block as shown. 2.7 L 4-cylinder (2TR-FE) engine 4.0 L V6 (1GR-FE) engine...
Page 424 6-1. Specifications Engine 2.7 L 4-cylinder (2TR-FE) engine Model 2TR-FE Type 4-cylinder in line, 4-cycle, gasoline 3.74 × 3.74 in. (95.0 × 95.0 mm) Bore and stroke Displacement 164.3 cu.in. (2694 cm Drive belt tension Automatic adjustment Valve clearance (engine cold) Automatic adjustment 　Intake 　Exhaust...
Page 425: Lubrication System
6-1. Specifications Lubrication system Oil capacity (Drain and refill - reference Without filter 2.7 L 4-cylinder (2TR-FE) engine 5.4 qt. (5.1 L, 4.5 Imp.qt.) 4.0 L V6 (1GR-FE) engine 2WD models except PreRunner: 4.4 qt. (4.2 L, 3.7 Imp.qt.) 4WD models and PreRunner: 5.2 qt.
Page 426 6-1. Specifications Engine oil selection ■ “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC GF-5 multigrade engine oil Recommended viscosity: 2.7 L 4-cylinder (2TR-FE) engine...
Page 427 6-1. Specifications 4.0 L V6 (1GR-FE) engine SAE 5W-30 SAE 5W-30 is the best choice for good fuel economy and good starting in cold weather. If SAE 5W-30 is not available, SAE 10W-30 oil may be used. However, it should be replaced Outside temperature with SAE 5W-30 at the next oil change.
Page 428: Cooling System
10.1 qt. (9.6 L, 8.4 Imp.qt.) Vehicles with a manual transmission 10.3 qt. (9.7 L, 8.5 Imp.qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 429: Electrical System
Oil type and viscosity 75W-85 GL-5 or equivalent Your Toyota vehicle is filled with “Toyota Genuine Differential Gear Oil” at the factory. Use Toyota approved “Toyota Genuine Differential Gear Oil” or an equivalent oil of matching quality to satisfy the above specification.
Page 430: Automatic Transmission
: The fluid capacity is the quantity of reference. If replacement is necessary, contact your Toyota dealer. NOTICE Automatic transmission fluid type (4-speed models) ■ Using automatic transmission fluid other than “Toyota Genuine ATF Type T-IV” may cause deterioration in shift quality, locking up of your transmission accompanied vibration, ultimately...
Page 431: Manual Transmission
6-1. Specifications Manual transmission Gear oil capacity (Reference) 2.7 L 4-cylinder (2TR-FE) engine 2WD models 2.7 qt. (2.6 L, 2.3 Imp.qt.) 4WD models 2.3 qt. (2.2 L, 1.9 Imp.qt.) 4.0 L V6 (1GR-FE) engine 1.9 qt. (1.8 L, 1.6 Imp.qt.) Gear oil type Gear oil API GL-4 or GL-5 Recommended gear oil viscosity...
Page 432 6-1. Specifications Brakes Pedal clearance 2WD models except 4.3 in. (110 mm) PreRunner PreRunner 4.2 in. (106 mm) 4WD models Without off-road package 4.2 in. (106 mm) With off-road package 3.4 in. (88 mm) 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) Pedal free play Brake pad wear limit 0.04 in.
Page 433 6-1. Specifications Steering Free play Less than 1.2 in. (30 mm) ® Automatic transmission fluid DEXRON II or Power steering fluid type Tires and wheels Type A Tire size P215/70R15 97S Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Rear tires: 33 psi (230 kPa, 2.3 kgf/cm or bar)
Page 434 6-1. Specifications Type B Tire size P245/75R16 109S Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Rear tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Spare tire: Tire inflation pressure 30 psi (210 kPa, 2.1 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 435 6-1. Specifications Type D Tire size P265/65R17 110S Front tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Rear tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Spare tire: Tire inflation pressure 29 psi (200 kPa, 2.0 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 436 6-1. Specifications Type F Tire size P265/60R18 109H Front tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Rear tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Spare tire: Tire inflation pressure 29 psi (200 kPa, 2.0 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 437: Light Bulbs
6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights — 60/55 Front fog lights — Front side marker — lights Front turn signal 4157 lights/parking lights/ 27/8 daytime running lights Exterior Rear turn signal lights 3157A 27/8 Stop/tail and rear side 3157KX 27/8 marker lights...
Page 438 ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada. Fuel tank opening for unleaded gasoline ■ To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps. If your engine knocks ■...
Page 439 10% ethanol). (85% ethanol) If you use gasohol in your Toyota, be sure that it has an octane rating no ● lower than 87. Toyota does not recommend the use of gasoline containing methanol.
Page 440 (Methylcyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.
Page 441 6-1. Specifications Tire information Typical tire symbols Tire size (→P. 472) DOT and Tire Identification Number (TIN) (→P. 471) Location of treadwear indicators (→P. 350) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
Page 442 6-1. Specifications Radial tires or bias-ply tires A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire. Summer tire or all season tire (→P. 354) An all season tire has M+S on the sidewall. A tire not marked M+S is a summer tire.
Page 443 6-1. Specifications Tire size Typical tire size information ■ The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol...
Page 444 U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades ■...
Page 445 6-1. Specifications Treadwear ■ The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100.
Page 446 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Glossary of tire terminology Tire related term Meaning...
Page 447 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as Occupant distribution specified in the third column of Table 1 below The combined weight of installed regular production options weighing over 5 lb.
Page 448 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
Page 449 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on Intended outboard the other sidewall of the tire, or sidewall...
Page 450 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between Ply separation adjacent plies A mechanical device made of rubber, chemicals, fabric and steel or other materials, Pneumatic tire that, when mounted on an automotive wheel, provides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that...
Page 451 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear designed to give a visual indication of the...
Page 452 Toyota dealership. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Customizing inside rear view mirror features (vehicles with auto anti-glare inside rear view mirror)
Page 453 6-2. Customization Type A: Press and select “Layout”. Type B: Press and select “Layout”. Type A: Press and hold and choose whether outside temperature or compass display will appear on top. Type B: Press and choose whether outside tempera- ture or compass display will appear on top. To leave the “Custom Settings Menu”, select “Back to main menu”...
Page 454 6-2. Customization Type A: Each time is pressed and held, the display col- ors change in the following order: “Green” → “White” → “Orange” → “Blue” Type B: Each time is pressed, the display colors change in the following order: “Green”...
Page 455: Customizable Features
6-2. Customization To leave the “Custom Settings Menu”, select “Back to main menu” to return to the starting screen, then either select “Exit” or wait several seconds without pressing any buttons. Customizable features Customized Item Function Default setting setting Wireless remote con- Operation signal trol...
Page 456 6-2. Customization Items to initialize The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle. Item When to initialize Reference After the maintenance is per- Maintenance data P.
Page 457 6-2. Customization...
Page 458 If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 459 Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.
Page 461 SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English.
Page 472 National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchas- ers and/or prospective purchasers of Toyota vehicles with infor- mation on truck-camper loading. Your Toyota dealer will help answer any questions you may have as you read this informa- tion.
Page 473 CAUTION Loading precaution ■ If a load is too far back, it can cause dangerous handling. If it is too far forward, the front axle may be overloaded. Cargo weight rating and proper matching When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the manufacturer’s camper weight figure, the weight of installed additional camper equipment not included in the manufacturer’s camper weight figure, the weight of camper cargo,...
Page 474 Access Cab models 2 people, 2TR-FE engine, 2WD except PreRunner: 750 lb. (340 kg) 4 people, 2TR-FE engine, 2WD except PreRunner: 450 lb. (204 kg) 2 people, 2TR-FE engine, PreRunner: 1000 lb. (453 kg) 4 people, 2TR-FE engine, PreRunner: 700 lb. (317 kg) 2 people, 1GR-FE engine, PreRunner: 950 lb.
Page 475 Gross axle and vehicle weight ratings Secure loose items to prevent weight shifts that could affect the bal- ance of your vehicle. When the truck camper is loaded, drive to a scale and weigh on the front and on the rear wheels separately to determine axle loads.
Page 476 GAWR ■ GAWR Front Rear 2WD models except PreRun- 2380 lb. (1075 kg) 2650 lb. (1200 kg) Regular Cab models 3000 lb. (1360 kg) 4WD models and 2755 lb. (1245 kg) Access Cab and PreRunner Double Cab models 3110 lb. (1410 kg) GVWR ■...
Page 477 PreRunner Cab type GVWR Vehicles with 2.7 L 4-cylinder (2TR-FE) engine Access Cab and 5250 lb. (2380 kg) Double Cab Vehicles with 4.0 L V6 (1GR-FE) engine 5400 lb. (2445 kg) 4WD models Cab type GVWR Regular Cab 5100 lb. (2310 kg) Vehicles with 2.7 L 4-cylinder (2TR-FE) engine 5350 lb.
Page 479 What to do if... What to do if... If you have a flat tire P. 413 A tire punctures P. 430 If the engine will not start The engine does not start P. 82 Engine immobilizer system If the vehicle battery is discharged P.
Page 480 What to do if... Instrument cluster ■ Center panel ■...
Page 481 What to do if... ■Warning lights Brake system warning Slip indicator* light P. 405 Cruise control indicator light* P. 403 P. 405 Automatic transmission Charging system warning fluid temperature light P. 404 warning light P. 405 Open door warning light Low engine oil pressure warning light P.
Page 482: Gas Station Information
GAS STATION INFORMATION Fuel filler door Auxiliary catch lever P. 79 P. 332 Tire inflation pressure Hood lock release lever P. 462 P. 332 Fuel tank capacity 21.1 gal. (80.0 L, 17.6 Imp.gal.) (Reference) Unleaded gasoline, Octane Rating 87 Fuel type (Research Octane Number 91) or higher Cold tire inflation P.
Page 483 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING Two Wheel Drive Four Wheel Drive Anti-Lock Brake System Accessory Automatic Locking Retractor A-TRAC Active Traction Control AUTO LSD Automatic Limited Slip Differential Child Restraint System Downhill assist control Electronic Control Unit Event Data Recorder Emergency Locking Retractor GAWR Gross Axle Weight Rating...
Page 484 Abbreviation list ABBREVIATIONS MEANING TPMS Tire Pressure Warning System TRAC Traction Control Treadwear indicators Trailer Weight Rating Vehicle Identification Number Vehicle Stability Control...

Toyota Tacoma 2013 Owner's Manual

Quick Links

TABLE OF CONTENTS

Related Manuals for Toyota Tacoma 2013

Summary of Contents for Toyota Tacoma 2013

Table of Contents