Grundig CUC 7303 FR Service Manual page 11

CUC 7303 FR
Special and Service Functions
1. Special Functions
1.1 Storing the Analog Values
The entered analog values are either stored automatically after approx.
8 seconds or when switching to standby mode.
1.2 Setting the Optimum Values
Pressing "PC/AUX" –> "OK" the television receiver is set to the
optimum values stored for brightness, contrast, colour contrast and
volume.
Optimum
Brightness 32
Colour contrast 32
BW contrast 50
Volume 30
Having stored the minimum volume level, the volume setting bar is
indicated on the screen for approx. 8 seconds as an optical information
when switching the power "on" or switching on from standby.
1.3 ATS Start
Press and hold the "P/C/AUX" button for approx. 4s until "ATS" (Auto
Tuning System) is indicated and confirm with "OK".
The ATS system stores the found station signal automatically (display:
channel and finetuning).
1.4 Maximum Programme Number (reversing point):
Press the " " –> "OK" buttons and enter "----" under the frequency
band selection option (B) at any programme position on the pro-
gramme setting menu . Confirm with "OK" and leave the menu. As a
result of this, programme selection in programme mode with the "P+/
P-" buttons is limited to the numbers lower than this position. If the
reversing point is ≤ 10 only one-place programme selection is possible.
1.5 Calling up the Service Menu at "Hotel mode on"
Press and hold button " " on the remote control and switch on with the
mains button. With the "P+/P-" button select the "Hotel" mode in the
menu and set the indication to "OFF" using the "
During the time the "Hotel mode" is active it is not possible to call up
the programme setting menu with the "PC/AUX" button.
2. Settings via the Service Menu
2.1 Calling up the Service Menu
Press and hold button " " on the remote control and switch on with the
mains button.
2.2 AGC Alignment
Select "AGC ALIGN" in the Service Menu. Alignment is possible in
range 0...62 with the " - / +
2.3 OSD Position
Press and hold button " " on the remote control and switch on with the
mains button. Select "OSD" (V or H) in the Service Menu and with the
" - / + " buttons position the menu table in the centre of the
screen.
2.4 Activating the Hotel Mode
Select "Hotel ON" in the Service Menu. When the Hotel mode is
activated:
it is no longer possible to call up the
the " " –> "OK" buttons.
the currently set volume level is stored as the maximum level
possible in this mode.
2.5 Decoder
Via the Service Menu switch the decoder "ON" or "OFF".
Decoder "ON":
Automatic identification of the switching voltage at Pin 8 of the EURO-
AV socket (e.g. descrambler operation with TVs in French version, or
external RGB mode for Italy).
2.6 Continuous Station Ident Indication
So that the programme name is displayed continuously on the screen
press the " " button. After about 8 seconds the programme is displayed
in reduced size.
GRUNDIG Service
Maximum
63
63
63
63
- or + " button.
" buttons.
programme setting menu with
3. Settings via the AUX Menu
3.1 AUX Overview
The AUX menu is called up by pressing the "PC/AUX" remote control
button quickly.
3.2 Calling up the Contrast Setting Option
Call up the AUX menu and adjust the contrast with "
3.3 Calling up the Sleeptimer
Call up the AUX menu and activate the timer with the "TXT" button.
Enter the desired stop time with the numbered buttons on the remote
control and leave the menu with button " ".
3.4 Optimum Values for Analog Functions
Call up the AUX menu and press "OK". The optimum values are now
called up.
3.5 ATS
Call up the AUX menu and press "PC/AUX" for approximately 4s.
Press the "OK" button to start the system.
3.6 Tint with NTSC
Call up the AUX menu and adjust with the button "
Partie générale / General Section
- / +" button.
- / + ".
1 - 11