Rear Panel - Panasonic GP-US522HB Operating Instructions Manual

17. Camera Cable Connector (CAMERA)
This 20-pin connector is used for connection with the
camera head via the optional camera cable GP-
CA522/4.
Fasten the camera cable to this connector firmly.
If not, noise may be appeared.
Caution
Connecting or disconnecting the camera cable
to/from the camera control unit or camera head
must be done after turning off the Power of the
camera control unit.
For Camera
24 23
22 21 20 19 18
17 16 15 14 13
12 11 10 9 8
7 6 5 4 3
2 1

[Rear Panel]

18. S-Video Output Connector (S-VIDEO)
The luminance (Y) and chrominance (C) signals for
VCR (VTR) or monitor are provided at this connector.
S-VIDEO (Mini-DIN,4-pin)
Pin No.
1 Y Ground (GND)
2 C Ground (GND)
3 Y Signal Output (For NTSC 0.714 V[P-P],
for PAL 0.7 V[P-P] (Y level)/75 Ω)
4 C Signal Output (For NTSC 0.286 V[P-P],
for PAL 0.3 V[P-P] (Burst Level)/75 Ω)
10
For CCU
1
2 5
6
10
11 15
19
16
20
!8 !9
VIDEO
S-VIDEO
RGB/YPbPr
@3
4 3
2 1
Description
Camera Head Side
1 +15 V Input
2 Ground (GND)
3 Chip Select 1 Input
4 +25 V Input/HCLR Output
5 VL Input
6 B Signal Output
SCANNING MODE
7
Select Input
8 Serial Data Input
9 Serial Clock Input
10 CCD Select Output
11 G Signal Output
12 R Signal Output
13 VD Input
14 CPOB Output
15 HD Input
16 +9 V Input/Not used
17 +5 V Input
18 Serial Data Output
19 Chip Select 2 Input
20 Not used
21 Not used
22 Not used
23 TGCLK Input
24 Not used
@0 @1 @2
G/L
VBS/HD VD ON
75Ω
OFF
RS-232C
@4
19. Video Output Connector (VIDEO)
A 1.0 V[P-P]/75 Ω composite video signal is provided at
this connector.
20. Gen-lock Signal Input Connector (VBS/HD)
The color video signal of the camera is automatically
synchronized with the gen-lock signal (Composite
Signal, Black Burst Signal or Video Sync) when either
signal is supplied to this connector.
The gen-lock signal is used for system reference.
Caution:
If the gen-lock signal is jittery (as in the case of a
VCR (VTR) playback picture), the camera cannot be
synchronized properly.
(External HD and VD Mode)
The horizontal and vertical pulse of the color video
signal is synchronized with the external HD fed to
this connector and external VD fed to the VD input
connector when using in the External HD and VD
Mode.
Camera Control Unit Side
1 Ground (GND)
2 Chip Select 2 Output
3 Serial Data Input
4 +9 V Output/Not used
5 VL Output
6 TGCLK Output
7 CPOB Input
SCANNING MODE
8
Select Output
9 +5 V Output
10 B Signal Input
11 Serial Clock Output
12 VD Output
13 Chip Select 1 Output
14 +25 V Output/HCLR Input
15 R Signal Input
16 Serial Data Output
17 HD Output
18 G Signal Input
19 +15 V Output
20 CCD Select Input
@5
OFF ON
ON
1 RGB YPbPr
2 INTER. PROGRE.
3 NOT USE NOT USE
1 2 3 4
4 RS-232C FRONT SW
DC 12V IN
@6