1. Manuals
  2. Brands
  3. Sony Manuals
  4. CD Player
  5. CDX-C8050X - Fm/am Compact Disc Player
  6. Service manual

Sony cdx-c8050x Service Manual

10 – 20,000 hz
Hide thumbs Also See for cdx-c8050x:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
• The tuner and CD sections have no adjustments.

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
19 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 10 Hz to 20 kHz with no more
than 1% total harmonic distortion.
Other Specifications
CD player section
System
Compact disc digital audio
system
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Laser Diode Properties
Material
GaAlAs
Wavelength
780 nm
Emission Duration
Continuous
Laser output power
Less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on the
Optical Pick-up Block.
Tuner section
FM
Tuning range
87.5 – 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
CDX-C8050X
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
Power amplifier section
Outputs
Speaker impedance
Maximum power output 50 W × 4 (at 4 ohms)
General
Outputs
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Design and specifications are subject to change without
notice.
FM/AM COMPACT DISC PLAYER
US Model
NEW
MG-383V-121//Q
KSS-720A
Speaker outputs
(sure seal connectors)
4 – 8 ohms
Audio outputs
Power antenna relay
control lead
Power amplifier control
lead
Telephone ATT control
lead
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 183 mm
× 2 × 7
(7
in.)
1/8
1/4
(w/h/d)
Approx. 182 × 53 × 162 mm
× 2
× 6
(7
in.)
1/4
1/8
1/2
(w/h/d)
Approx. 1.3 kg (2 lb. 14 oz.)
Card remote commander RM-X91
Parts for installation and
connections (1 set)
Front panel case (1)
1

Advertisement

Table of Contents
loading

Related Manuals for Sony cdx-c8050x

Summary of Contents for Sony cdx-c8050x

  • Page 1: Specifications

    CDX-C8050X SERVICE MANUAL US Model • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CD Drive Mechanism Type MG-383V-121//Q SPECIFICATIONS Optical Pick-up Name KSS-720A AUDIO POWER SPECIFICATIONS Power amplifier section Outputs Speaker outputs POWER OUTPUT AND TOTAL HARMONIC DISTORTION...

  • Page 2: Table Of Contents

    THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. 3-17. Schematic Diagram –Sub (CD) Section– ......43 REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE 3-18. Printed Wiring Board –Key Section– ........ 44 PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

  • Page 3: General

    ENTER 2 MENU button SHUF MENU DISC LIST MODE 3 SOURCE button SEEK SEEK CDX-C8050X/MDX-C8500X 4 SEEK/AMS (cursor </,) buttons SOURCE 5 SOUND button SOUND DISC ENTER 6 DSPL button Refer to the pages listed for details. 7 ATT button...

  • Page 4: Cd/Md

    Close the front panel. The track number indication returns to “1, ” and playback restarts from the first track of the To play back an 8 cm (3 in.) CD, use the optional Sony compact disc single adapter (CSA-8). Press (OFF) Stop playback...

  • Page 5: Radio

    Tips Erasing the disc memo Labeling a CD • To erase or correct a name, enter “ ” (under- Locating a disc by name — Disc Memo bar) for each character. Press (SOURCE) repeatedly to select (For a CD unit with the custom file function) •...

  • Page 6: Dsp

    Tips If FM stereo reception is poor Receiving the memorized Storing the station names • To erase or correct a name, enter “ ” (under- — Monaural Mode bar) for each character. stations — Station Memo • When storing station names, there is an During radio reception, press (MENU), alternative method;...

  • Page 7: Other Functions

    Select the desired frequency and level. Selecting the DSO Selecting a soundstage Adjusting the front and 1 Press either side of (SEEK/AMS) to Press (SOURCE) to select a source (tuner, select the cut-off frequency. menu rear fader CD, or MD). —...

  • Page 8: Tv/Video

    If you need to mount the rotary commander By rotating the control Other operations Using the rotary on the right hand side of the steering column, (the SEEK/AMS control) Rotate the VOL control to you can reverse the operative direction. adjust the volume.

  • Page 9: Additional Information

    The front cover is removed. be an internal malfunction. In such a case, Main unit consult your nearest Sony dealer. Back of the front panel Fuse (10 A) Notes • For safety, turn off the engine before cleaning...

  • Page 10: Connections

    Connections Connexions Conexiones Caution Précautions Precauciones •This unit is designed for negative ground 12 V DC operation only. •Cet appareil est exclusivement conçu pour fonctionner sur une •Esta unidad ha sido diseñada para alimentarse con 12 V CC, tension de 12 V CC avec masse négative. negativo a masa, solamente.
  • Page 11 Connection example RCA pin cord (not supplied) Cordon à broche RCA (non fourni) Exemple de connection Cable con pines RCA (no suministrado) Ejemplo de conexiones Source selector (not supplied) Supplied to the CD/MD changer Sélecteur de source (non fourni) Fourni avec le changeur de CD/MD Suministrado con el cambiador de CD/MD Selector de fuente (no suministrado)

  • Page 12: Disassembly

    SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. SUB PANEL ASSY 4 two claws 6 sub panel assy 2 PTT 2.6x8 3 claw 5 CN701 1 PTT 2.6x8 2-2. CD MECHANISM BLOCK 7 bracket (CD) 6 PTT 2.6x5 5 CD mechanism block 2 PTT 2.6x5...

  • Page 13: Main Board

    2-3. MAIN BOARD 6 ground point screw 8 MAIN board (PTT 2.6x6) 7 ground point screws (PTT 2.6x6) 5 PTT 2.6x10 1 CN301 4 PTT 2.6x10 3 cord (connector) 2 PTT 2.6x10 2-4. HEAT SINK 7 heat sink 6 PTT 2.6x8 5 PTT 2.6x8 4 PTT 2.6x8 3 PTT 2.6x12...

  • Page 14: Chassis (T) Assy

    2-5. CHASSIS (T) ASSY 2 P 2x3 3 P 2x3 1 Unsolder the 4 chassis (T) assy lead wires. black white 2-6. LEVER ASSY 5 guide (disc) 6 lever (R) assy 3 tension spring (LR) 7 lever (L) assy 1 PS 2x4 2 DISC IN SW board 4 claws...

  • Page 15: Servo Board

    2-7. SERVO BOARD 7 PS 2x4 8 PS 2x4 2 CN2 3 Removal the solders. 1 CN3 5 P 2x3 9 SERVO board 4 Removal the solders. 6 loading motor assy (M903) 2-8. ARM ROLLER ASSY • When installing, take note of the positions arm (roller) and washers.

  • Page 16: Chassis (Op) Assy

    2-9. CHASSIS (OP) ASSY 7 chassis (OP) assy 8 compression spring (FL) 1 tension spring (KF1) 9 compression spring (FL) 2 tension spring (KR1) 5 Fit lever (D) in the direction of the arrow. 6 Turn loading ring in the direction of the arrow.

  • Page 17: Diagrams

    SECTION 3 DIAGRAMS 3-1. IC PIN DESCRIPTIONS • IC501 CXD2598Q (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name Pin Description DVDD — Digital power supply pin DVSS — Digital ground SOUT Servo brock serial data output (Not used.) SOCK Servo brock serial data read clock output (Not used.) XOLT...
  • Page 18 Pin No. Pin Name Pin Description Tracking error signal input Center servo analog input RFDC RF signal input ADIO Test pin (Not used.) AVSSO — Analog ground IGEN Constant current input from OP amplifier. AVDDO — Analog ground ASYO EFM full-swing output (“L”: VSS, “H”: VDD) ASYI Asymmetry comparate voltage input RFAC...
  • Page 19 • IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name Pin Description ITRPT — Not used in this set. 2, 3 — — Not used in this set. 4, 5 — Not used in this set. OPEN Front panel open detection input CLOSE Front panel close control output LINKOFF...
  • Page 20 Pin No. Pin Name Pin Description SENS SENS signal input — — Not used in this set. — — Not used in this set. BU.IN Back-up power detection input BUSON Bus on control input IN SW Disc in switch input (SW1) SELF SW Self switch input (SW2) SCOR...
  • Page 21 Display serial data output to the liquid crystal display driver (IC901) Bus on/off control signal output to the CD mechanism controller (IC5), liquid crystal BUS-ON display drive controller (IC701) and SONY bus interface (IC601) “L”: bus on BEEP Beep sound drive signal output terminal...
  • Page 22 Data transmit completed detection signal input from the RDS decoder (IC201) DAVN “L” active Not used (open) DISCON_IN CD/MD on/off control signal input from the CD mechanism controller (IC5) Battery detection signal input from the SONY bus interface (IC601) and battery detect BUIN circuit “L” is input at low voltage...
  • Page 23 Pin No. Pin Name Pin Description Transfer enable signal input from the CXD2726Q (IC805) DSPRADY “L”: transfer prohibition, “H”: transfer permission Input of acknowledge signal for the key entry Acknowledge signal is input to KEYACK accept function and eject keys in the power off status On at input of “H” A/D converter power control signal output terminal ADON When the KEYACK (pin ul) that controls reference voltage power for key A/D...
  • Page 24 Pin No. Pin Name Pin Description Dial pulse input of the rotary encoder (RE901) (B phase input) REIN0 (for VOLUME/BASS/TREBLE/BALANCE/FADER control) Front panel block remove/attach detection signal input from the nose detection swich NOSESW (S102) “L”: front panel is attached LED drive signal output of the CD disc slot illumination and Z indicator (LED771 –...
  • Page 25 • IC805 CXD2726Q-4 (DIGITAL SIGNAL PROCESSOR, DIGITAL FILTER, D/A CONVERTER) (DSO BOARD) Pin No. Pin Name Pin Description Pin No. Pin Name Pin Description RVDT Serial data input from the master controller (IC502) DGND — Ground terminal (digital system) Serial data 24/32 bit slot selection signal input terminal 24/23BIT 2 –...

  • Page 26: Block Diagram -Cd Section

    CDX-C8050X 3-2. BLOCK DIAGRAM — CD SECTION — BATT BATT CHECK Q352 RF AMP, LD APC, DIGITAL SERVO, TO TUNER CD SYSTEM CONTROL SYSTEM CONTROL OPTICAL PICKUP ERROR AMP DIGITAL SIGNAL PROCESSOR TO DISPLAY SECTION IC502 (1/3) KSS-720A IC501 (Page •...

  • Page 27: Block Diagram -Tuner Section

    CDX-C8050X 3-3. BLOCK DIAGRAM — TUNER SECTION — CN302 –1 BUS AUDIO IN –2 L-CH LINE DRIVER R-CH ELECTRONIC VOLUME IC303 IC301 –5 OUT FL AUDIO OUT Q356 –6 FRONT 34 ACINLF R-CH 33 AC INLR TO DISPLAY TUNER UNIT 35 SWINR –3...

  • Page 28: Block Diagram -Display Section

    CDX-C8050X 3-4. BLOCK DIAGRAM — DISPLAY SECTION — SUB SYSTEM CONTROL IC701 BUS SI UNI SI SP SI SP SCK UNI SO UNI SO SYSTEM CONTROL UNI SCK BUS CLK IC502 (3/3) RE901 IC805 BUS ON BUS ON ROTALY IC807...

  • Page 29: Circuit Boards Location

    • Waveforms (MODE:PLAY) 3-5. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF Approx.

  • Page 30: Printed Wiring Boards -Cd Mechanism Section

    CDX-C8050X 3-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION —...
  • Page 31 CDX-C8050X • Semiconductor Location Ref. No. Location IC501 Q101 (Page 35)

  • Page 32: Schematic Diagram -Cd Mechanism Section (1/2)

    CDX-C8050X • Refer to page 29 for Waveforms. 3-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 46 for IC Block Diagrams. Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions.

  • Page 33: Schematic Diagram -Cd Mechanism Section (2/2)

    CDX-C8050X • Refer to page 29 for Waveforms. 3-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 46 for IC Block Diagrams. (Page 32) Note: • Voltage is dc with respect to ground under no-signal conditions.

  • Page 34: Printed Wiring Board -Main Section

    CDX-C8050X 3-9. PRINTED WIRING BOARD — MAIN SECTION — • Semiconductor Location (Side A) Ref. No. Location Ref. No. Location D101 IC504 D102 IC601 D104 IC701 J-10 D105 IC702 H-11 D106 D107 Q101 D108 Q102 D109 Q103 D201 D-12 Q106...
  • Page 35 CDX-C8050X (Page 31) • Semiconductor Location (Side B) Ref. No. Location D103 D355 D356 D357 D358 D359 D360 D361 D362 D363 (Page 40) D604 D605 D606 D611 D-11 D612 D613 IC351 Q104 Q105 Q107 Q110 Q402 Q406 Q704 I-13 SUB (CD) BOARD...

  • Page 36: Schematic Diagram -Main Section (1/4)

    CDX-C8050X 3-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 46 for IC Block Diagrams. (Page 41) (Page 38) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ) : AM...

  • Page 37: Schematic Diagram -Main Section (2/4)

    CDX-C8050X 3-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — (Page 38) (Page 39) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 38: Schematic Diagram -Main Section (3/4)

    CDX-C8050X 3-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 46 for IC Block Diagrams. (Page 36) (Page 37) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ) : AM <...

  • Page 39: Schematic Diagram -Main Section (4/4)

    CDX-C8050X 3-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — (Page 37) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 40: Printed Wiring Board -Dso Section

    CDX-C8050X 3-14. PRINTED WIRING BOARD — DSO SECTION — • Semiconductor Location Ref. No. Location D801 (D802) D804 IC801 (IC802) IC803 IC804 (IC805) (IC807) (IC808) IC809 Q801 Q802 ): SIDE B (Page 35)

  • Page 41: Schematic Diagram -Dso Section

    CDX-C8050X 3-15. SCHEMATIC DIAGRAM — DSO SECTION — Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 42: Printed Wiring Board -Sub (Cd) Section

    CDX-C8050X 3-16. PRINTED WIRING BOARD — SUB (CD) SECTION — SUB (CD) BOARD (Page 35) SUB (CD) BOARD (Page 44)

  • Page 43: Schematic Diagram -Sub (Cd) Section

    CDX-C8050X 3-17. SCHEMATIC DIAGRAM — SUB (CD) SECTION — SUB (CD) BOARD (Page 45) (Page 39) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 44: Printed Wiring Board -Key Section

    CDX-C8050X 3-18. PRINTED WIRING BOARD — KEY SECTION — • Semiconductor Location SUB (CD) BOARD Ref. No. Location Ref. No. Location (D901) B-13 LED902 (Page 42) (D902) C-11 LED903 LED904 (D903) C-11 (D904) C-11 LED910 B-12 (D951) LED911 B-12 LED912...

  • Page 45: Schematic Diagram -Key Section

    CDX-C8050X 3-19. SCHEMATIC DIAGRAM — KEY SECTION — Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...
  • Page 46 • IC Block Diagrams IC1 CXA2596M IC7 LA6556L-TE-L IC303, 304, 305 NJM2160AM-TE2 APC PD AMP HOLD S-GND – VCCL BUFFER INPUT CH2-CH4 OUTPUT – SVRL CL– 35 MUTE2 MUTE2 ON/OFF LIFT AGCVTH 23 LC/PD BUFFER CH1 OUTPUT – APC LD AMP VCC2 34 MUTE1 MUTE1...
  • Page 47 IC301 TDA7402TR 32 31 30 29 28 27 26 25 24 23 MONO SUPPLY FADER MIXER SUBWOOFER MONO MONO +PHASE FADER FADER CONTROL ACINLF OUTPUT CONTROL SWINR SWINL MUTE AC OUTR VOICE AC OUTL BANDPASS C-BUS QUAL. QUAL BASS HIGH OUT DIGITAL TRABLE CONTROL...

  • Page 48: Exploded Views

    SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by number in the exploded views are not supplied. Example : mark 0 or dotted line with mark • Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ...

  • Page 49: Front Panel Section

    4-2. FRONT PANEL SECTION not supplied (KEY board) LCD900 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-040-980-01 BUTTON (SOURCE) 3-041-010-01 BUTTON (1-6/M) 3-042-458-01 KNOB (VOL-DSO) 3-041-003-01 BUTTON (LIST/ENTER) * 53 3-040-992-02 HOLDER (LCD) 3-040-987-02 BUTTON (OFF) X-3378-398-1 PANEL ASSY, FRONT BACK 3-040-986-01 BUTTON (MENU/SOUND) X-3379-018-1 PANEL SUB ASSY...

  • Page 50: Cd Mechanism Section (1)

    4-3. CD MECHANISM SECTION (1) (MG-383V-121//Q) not supplied not supplied M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 1-659-836-11 DISC IN SW BOARD * 107 A-3326-232-A SERVO BOARD, COMPLETE * 102 A-3315-034-B CHASSIS (T) ASSY * 108 3-039-629-01 BRACKET (MOTOR) 3-931-909-01 SPRING (LR), TENSION...

  • Page 51: Cd Mechanism Section (2)

    4-4. CD MECHANISM SECTION (2) (MG-383V-121//Q) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3378-956-1 ARM ASSY, CHUCKING 3-931-883-01 SPRING (TR), TENSION 3-931-897-61 DAMPER (T) 3-931-881-01 LEVER (LOCK) 3-039-627-01 LEVER (D) 3-931-882-02 GEAR (MDL) 3-040-165-01 RETAINER (DISC) 3-007-537-11 WHEEL (U), WORM 3-018-272-01 WASHER 3-032-484-01 SPRING (KR1), TENSION...

  • Page 52: Cd Mechanism Section (3)

    4-5. CD MECHANISM SECTION (3) (MG-383V-121//Q) M901 M902 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3378-598-1 CHASSIS (OP) ASSY (INCLUDING M901)

  • Page 53: Electrical Parts List

    SECTION 5 DISC IN SW ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 54 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < FERRITE BEAD > R822 1-216-809-11 METAL CHIP 1/16W R823 1-216-821-11 METAL CHIP 1/16W FB801 1-414-235-22 FERRITE BEAD INDUCTOR R825 1-216-809-11 METAL CHIP 1/16W FB803 1-500-329-21 FERRITE BEAD INDUCTOR R826 1-216-864-11 METAL CHIP 1/16W...
  • Page 55 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R894 1-216-821-11 METAL CHIP 1/16W LED912 8-719-078-19 LED LWA673-R1S2 (LCD BACK LIGHT) R895 1-216-833-11 RES-CHIP 1/16W LED913 8-719-078-19 LED LWA673-R1S2 (LCD BACK LIGHT) R899 1-216-864-11 METAL CHIP 1/16W LED914 8-719-078-19 LED LWA673-R1S2 (LCD BACK LIGHT) LED915 8-719-078-19 LED LWA673-R1S2 (LCD BACK LIGHT) <...
  • Page 56 LIMIT SW LOAD SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R938 1-216-809-11 METAL CHIP 1/16W A-3294-903-A MAIN BOARD, COMPLETE R939 1-216-813-11 METAL CHIP 1/16W (INCLUDING DSO BOARD, COMPLETE) R940 1-216-821-11 METAL CHIP 1/16W ********************* R951 1-216-819-11 METAL CHIP...
  • Page 57 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C234 1-164-489-11 CERAMIC CHIP 0.22uF C353 1-127-573-11 CERAMIC CHIP C237 1-126-157-11 ELECT 10uF C354 1-104-942-11 ELECT C246 1-163-038-00 CERAMIC CHIP 0.1uF C355 1-162-919-11 CERAMIC CHIP 22PF C301 1-164-346-11 CERAMIC CHIP C356 1-162-919-11 CERAMIC CHIP...
  • Page 58 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C513 1-163-038-00 CERAMIC CHIP 0.1uF D105 8-719-422-86 DIODE MA8082-L-TX C514 1-163-237-11 CERAMIC CHIP 27PF D106 8-719-060-81 DIODE MA735-TX C515 1-163-237-11 CERAMIC CHIP 27PF D107 8-719-422-62 DIODE MA8062-L-TX C516 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 59 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > Q352 8-729-120-28 TRANSISTOR 2SC2412K-T-146-R Q353 8-729-424-59 TRANSISTOR UN2212-TX IC301 8-759-653-27 IC TDA7402TR Q354 8-729-424-18 TRANSISTOR UN2113-TX IC302 8-759-521-35 IC TL5001CDR Q355 8-729-424-59 TRANSISTOR UN2212-TX IC303 8-759-593-97 IC NJM2160AM-TE2 Q356...
  • Page 60 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R124 1-216-845-11 METAL CHIP 100K 1/16W R323 1-216-081-00 METAL CHIP 1/10W R125 1-216-308-00 METAL CHIP 1/10W R324 1-216-049-11 RES-CHIP 1/10W R126 1-216-845-11 METAL CHIP 100K 1/16W R325 1-216-085-00 METAL CHIP 1/10W R127...
  • Page 61 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R384 1-216-041-11 METAL CHIP 1/10W R540 1-216-069-00 RES-CHIP 6.8K 1/10W R385 1-216-041-11 METAL CHIP 1/10W R542 1-216-833-11 RES-CHIP 1/16W R386 1-216-041-11 METAL CHIP 1/10W R543 1-216-097-11 RES-CHIP 100K 1/10W R387...
  • Page 62 MAIN SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R727 1-216-809-11 METAL CHIP 1/16W C302 1-164-360-11 CERAMIC CHIP 0.1uF R728 1-216-809-11 METAL CHIP 1/16W C303 1-164-227-11 CERAMIC CHIP 0.022uF R729 1-216-821-11 METAL CHIP 1/16W C304 1-164-227-11 CERAMIC CHIP 0.022uF R731...
  • Page 63 SERVO SUB (CD) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JR504 1-216-864-11 METAL CHIP 1/16W R508 1-216-809-11 METAL CHIP 1/16W JR507 1-216-295-00 SHORT R509 1-216-809-11 METAL CHIP 1/16W R510 1-216-809-11 METAL CHIP 1/16W < TRANSISTOR > R511 1-216-845-11 METAL CHIP 100K...
  • Page 64 CDX-C8050X SUB (CD) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > ************** HARDWARE LIST LED771 8-719-037-97 LED CL-190R-CD-T (DISC IN) ************** LED772 8-719-037-97 LED CL-190R-CD-T (DISC IN) LED773 8-719-037-97 LED CL-190R-CD-T (DISC IN) 7-685-793-09 SCREW +PTT 2.6X8 (S)

Table of Contents