Troubleshooting - Black & Decker STC1820E User Manual

ENGLISH (Original instructions)

Troubleshooting

Problem Solution
Appliance runs slowly. Remove battery from trimmer.
Check that the spool housing can rotate
freely. Carefully clean it if necessary.
Check that the cutting line does not
protrude more than approximately
122 mm from the spool. If it does, cut
it off so that it just reaches the line
trimming blade
Automatic line feed does not More line is fed when the line shortens
feed line. to approximately 76 mm. To determine if
the line is not feeding, let line wear past
this point.
Keep the tabs depressed and remove the
spoolcap with the spool from the spool
housing in the trimmer head.
Ensure that the line is not crisscrossed
on the spool as detailed in (Fig. U). If
it is unwind the cutting line and rewind
it neatly.
Inspect tracks at the bottom of spool for
damage. If damaged, replace spool.
Pull the cutting line until it protrudes
approximately 122 mm from the spool. If
insufficient cutting line is left on the spool,
install a new spool of cutting line.
Align the tabs on the spool cap with the
cut outs in the housing.
Push the spool cap onto the housing until
it snaps securely into place.
If the cutting line protrudes beyond the
trimming blade, cut it off so that it just
reaches the blade. If the automatic line
feed still does not work or the spool is
jammed, try the following suggestions:
Carefully clean the spool and housing.
Make sure you are using correct line
size and diameter (2.00 mm) - smaller
and larger line sizes will affect the
functionality of the auto feed system.
Remove the spool and check if the lever
in the spool housing can move freely.
Remove the spool and unwind the cutting
line, then wind it on neatly again. Replace
the spool into the housing.
Overfeeding Ensure you are cutting with the tip of
the line 177 mm from the spool. Use the
edge guide if needed to ensure proper
space is maintained.
Ensure you are not exceeding a 10º
angle as shown in (Fig. J1). Avoid contact
of the line with hard surfaces such as
brick, concrete, wood etc. This will
prevent excessive wear and/or overfeed
of line. Cut with the tip of the line
Line unravels when cap or Make sure to park the lines in holding
spool is removed slots (Figure P) before removing.
14
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
STC1820E
Input Voltage 18
V
DC
No-Load Speed -1 5500 - 7400
min
Weight kg 2.1
STC1840E
Input Voltage
V 18
DC
-1
No-Load Speed 5500 - 7200
min
Weight kg 2.1
Battery BL2018 - STC1820E
Voltage 18V
V
DC
Capacity Ah 2.0
Type Li-Ion
Battery BL4018 - STC1840E
Voltage 18V
V
DC
Capacity Ah 4.0
Type Li-Ion
905902××
905998** 906068**
Charger
(Type 1)
Input
100-240V 230V 230V
V
Voltage
AC
Output
18V 18V 18V
V
Voltage
DC
Current mA 400 1000 2000
Hand/arm weighted vibration value according to
EN50636-2-91:
= < 2,5 m/s , uncertainty (K) = 1,5 m/s .
2 2
L (sound pressure) 79 dB(A)
PA
uncertainty (K) = 3 dB(A)
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
STC1820E, STC1840E
Cordless String Trimmer
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN60335-1:2012 + A11:2014
EN50636-2-91:2014
2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VI
DEKRA Certification B.V., Utrechtseweg 310,
6802 ED Arnhem, The Netherlands
Notified Body ID No.: 0344
Level of sound power according to 2000/14/EC
(Article 12, Annex III, L ≤ 50 cm):
L (measured sound power) 93 dB(A)
WA
uncertainty (K) = 3 dB(A)
L (guaranteed sound power) 96 dB(A)
WA
These products also comply with Directive 2014/108/EC (until
19.04.2016), 2014/30/EU (from 20.04.2016) and 2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
R. Laverick
Director of Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
13/11/2015
(Original instructions) ENGLISH
Guarantee
Black & Decker is confident of the quality of its products
and offers consumers a 24 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Black&Decker Terms and Conditions and you will need to
submit proof of purchase to the seller or an authorised repair
agent. Terms and conditions of the Black&Decker 2 year
guarantee and the location of your nearest authorised repair
agent can be obtained on the Internet at www.2helpU.com, or
by contacting your local Black & Decker office at the address
indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and receive updates on new
products and special offers.
15