Cabinet Disassembly Instructions; Screw Torque Specification; Disassembly Flowchart - Philips 55PFL4909 Service Manual

CABINET DISASSEMBLY INSTRUCTIONS

Screw Torque Specification

Ref. Part
Part Name
No. Number
SCREW F-PAN BLACK_NI
L10 GCHP3120
+P-TITE M3X12.0
SCREW BIND 3CHROM
L23 GBJS3060
+S-TITE M3X6.0
SCREW F-PAN BLACK_NI
L28 GCHS3080
+S-TITE M3X8.0
SEMS-SW PAN BLACK_NI
L42 FPH34120
+ M4X12.0
STAND SCREW KIT
SSK1 1ESA34506 (SEMS-SW PAN BLACK_NI
+ M4X12.0)
* For reference

1. Disassembly Flowchart

This flowchart indicates the disassembly steps for the
cabinet parts and the CBA in order to gain access
to items to be serviced. When reassembling, follow
the steps in reverse order. Bend, route and dress
the cables as they were.
[1] Stand Base
Assembly
[2] Rear
Cabinet R
[4] Power Supply
[3] Rear
CBA Cabinet L
[8] Speaker [6] Stand Bracket
[9] Speaker
[7] T-CON Holder
Holder
[11] IR Sensor
CBA Unit
[12] LCD Panel
Assembly
2. Disassembly Method
Step/
Fig.
Loc. Part
No.
No.
Stand Base 8(S-1), Stand Hinge
[1] D1
Assembly Assembly
Rear 13(S-2), 6(S-3),
[2] D1
Cabinet R 2(S-4), 8(L-1)
Rear 9(S-5), 4(S-6),
[3] D1
Cabinet L 2(S-7), 8(L-2)
Tightening
Torque
5.2±0.9lb·in
(approx.
*
8.7±0.9lb·in)
[10] Function
CBA Unit
[5] Digital Main
CBA Unit
Removal Note
---
---
---
4-1
Step/
Fig.
Loc. Part
No.
No.
Power 5(S-8), CN501,
D2
[4] Supply CN601, CN1101,
D5
CBA CN1201, CN1401
4(S-9), CN3013
Digital Main D2 CN3101
[5]
CBA Unit D5 CN3801, CN3906
Jack Holder
Stand
[6] D3 ---------------
Bracket
T-CON
[7] D3 (S-10)
Holder
[8] Speaker D3 ----------------
Speaker
[9] D3 2(S-11)
Holder
CN4051, Function
Function D3
[10] Knob, Knob Frame,
CBA Unit D5
Hook
IR Sensor D3
[11] Sensor Shield, Hook
CBA Unit D5
Decoration Plate,LED
LCD Panel
[12] D4 Lens, Leading Edge
Assembly
Cover, Hook
  
(1) (2) (3)
*1: TYPE A
*2: TYPE B
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
e.g. 2(S-2) = two Screws of (S-2),
2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following "Reference Notes in the
Table."
Removal Note
---
*2 ,
*2 , CN3105 *1 ,
---
*1
,
---
---
---
---
2
2
1
 
(4) (5)
PL14.26-A_DC